Moxa Technologies VPort 66-2MP Series User manual

P/N: 1802000661010
*1802000661010*
VPort 66-2MP Series
Quick Installation Guide
Edition 1.0, September 2015
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2015 Moxa Inc. All rights reserved.

- 2 -
Overview
The VPort 66-2MP is a vandal-proof, IP66-rated, PTZ speed dome IP
camera for use in harsh, outdoor environments. With a 360° endless PAN,
-6 to 96° TILT, 22X/30X optical/20X digital zoom, H.264/MJPEG triple
video streams, day-and-night camera lens, and -40 to 65°C operating
temperature, the VPort 66-2MP is especially well-suited for outdoor video
surveillance applications.
Package Checklist
Moxa’s VPort 66-2MP is shipped with the following items. If any of these
items is missing or damaged, please contact your customer service
representative for assistance.
•1 × VPort 66-2MP
Model
Lens
Power
Ethernet
VPort 66-2MP-CAM22X f=4.3 mm (wide)
to 94.6 mm (tele),
24 VDC/VAC RJ45
VPort 66-2MP-CAM30X
f=4.3 mm (wide)
to 129.0 mm (tele)
24 VDC/VAC
RJ45
•Screw handle accessory package
Torx screw driver for
attaching/detaching the top
cover.
3.5 mm power jack to 2-pin
terminal block connector for
2-wire power line connection.
Silica gel dry bag (silica gel
desiccant)
for absorbing moisture
inside the camera.
Hook-and-loop fasteners for
attaching the dry bag inside the
camera.
•Quick Installation Guide
•Documentation and software CD (includes user’s manual, Quick
Installation Guide, and utility)
•Warranty card
NOTE
Check the model name on the VPort’s side label to determine if
the model name is correct for your order.

- 3 -
NOTE
This product must be installed in compliance with your local laws
and regulations.
Features
•Maximum 60 FPS @ full HD (1080P, 1920x1080) resolution (only in
single stream mode)
•22X/30X optical and 20X digital zoom (22X: 4.3 to 94.6 mm,
30X: 4.3 to 129 mm)
•Supports MJPEG and H.264 dual codecs
•Supports Full HD/SXGA/WXGA/720P/SVGA/ Full D1/ 4CIF/ VGA/
CIF/QVGA resolution
•TCP, UDP, and HTTP network transmission modes
•Supports QoS (ToS) for transmission priority
•Supports RTSP streaming
•Supports multicast (IGMP) video streaming
•Supports SNMP (V1/V2C/V3) for network system integration and
management
•Accessible IP filtering
•UPnP supported
•Built-in web server for easy configuration
•360° endless pan and -6° to +96° tilt
•Manual max pan speed of 120°/s; Preset max of 255°/s; Alarm
Trigger max of 360°/s*
•Supports PTZ movement calibration
•Minimum illumination up to 0.4 lux (color) and 0.03 lux (B/W)
•Built-in tamper alarm and Video Motion Detection (VMD)
•-40 to 65°C operating temperature
•1 10/100BaseT(X) port with RJ45 connector
•IP66 protection and NEMA Type 4X form factor
•SDXC slot for local event / disconnected recording
•CBR Pro for flexible flow control
•DynaStream™ for network efficiency with dynamic frame rate change
•EN50121-4 compliance
•Supports ONVIF Profile S for multiple video stream profiles
•24 VDC/VAC power input
•Supports NTCIP 1205
•EN 62262 IK10 level vandal resistance
•CE, FCC, UL 60950-1
•Pre, Trigger, and post snapshot images supported
•Sequential snapshot images supported
•Supports SMTP and FTP for alarm message transmission
•Supports HTTP event server
•3-year warranty for product, and 1-year warranty for moving parts**
*
When the temperature is under -10°C, the maximum PT speed will be
reduced to a max. of 130°/sec.
**
The following moving parts come with a 1-year warranty:
•
Fan
•
Shutter
•
Zoom lens
•
DC-Iris, P-Iris lens
•
PAN, TILT and lens motors/ mechanism
•Slip ring

- 4 -
VPort 66-2MP Product Description
Appearance
•Top cover screws: Four screws used to secure the top cover.
•Top cover: The top cover can be removed to take out the camera
body for installing or re-installing the SD card.
•Zoom Lens: The VPort 66-2MP-M12 supports 2 lenses with different
optical zoom specs:
22X: f = 4.3 mm (wide) to 94.6 mm (tele), F1.6 to F4.5
30X: f = 4.3 mm (wide) to 129.0 mm (tele), F1.6 to F4.7
•Dome cover: The VPort 66-2MP has a vandal-proof PC dome cover,
satisfying EN 62262 (IEC 62262) class IK10 level.
•Mounting kit: For installing the VPort 66-2MP on a wall or pole. The
mounting kit is not included as a standard accessory with the VPort
66-2MP; it must be ordered and purchased separately. Refer to the
ordering information on the VPort 66-2MP’s datasheet or webpage for
mounting accessory information.
NOTE
The color of the dome cover can be customized based on your
installation environment. Please contact your Moxa sales
representative for information about this customization service.
Note that the color of the dome cover could decrease the light
transmittance of the video image. The darker the dome cover,
the greater the decrease of light transmittance.
Inside the camera
•Camera module: The main body of the VPort 66-2MP.
•Camera module connector: A patented connector for connecting
the camera module with the external connectors with cables.

- 5 -
•SD card socket (SDXC): The VPort 66-2MP supports the SDXC
interface, which can use SD cards with more than 64 GB of memory
for local storage of video recordings (by event or continuous
recording).
NOTE
Since video recording requires a high frequency of read and write
actions
, we recommend using high performance,
high reliability
SD cards, such as Sca
ndisk or Transcend high-end SD cards.
Most important
ly, we highly recommend backing up videos
recorded
on an SD card to a
video recorder, hard disk, or other
more permanent storage media.
External cables and connectors
•Power connector: The VPort 66-2MP supports one 24 VDC or 24
VAC power input, with a 3.5 mm power jack male connector. You can
use a standard 24 VDC/VAC power adapter (3 A min.) to power the
VPort 66-2MP. In addition, a 3.5 mm power jack to 2-pin terminal
block connector is included as a standard VPort 66-2MP accessory for
direct power line connections.
VPort 66-2MP Power Consumption Information
Heater/Fan
Operation
PTZ
Operation
Temp. (inside
the camera)
Power
consumption
Heater/Fan off
Off
0 to 35°C
19 watts
Heater/Fan off
Operating
27 watts
Heater/Fan on
Off
-40 to 0°C
67 watts
Heater/Fan on
Operating
71 watts
Heater off / Fan on
Off
≥35°C
24 watts
Heater off / Fan on
Operating
31 watts

- 6 -
NOTE
•The heater and fan will be enabled when the internal
temperature is under -
10°C, and disabled when above 0°C.
The fan will be enabled when the internal temperature is
above 50°C, and disabled when under 35°C.
•
When using the 3.5 mm power jack to 2-pin terminal block
connector for a direct power line connection, be sure to pay
attention to the “+” and “-“ pin assignments on the
connector.
•
The power input rating of the VPort 66-
2MP is 24 VDC (21.6
to 26.4 VDC) or 24 VAC (21.6 to 26.4 VAC).
•Reset button: For rebooting and restoring factory defaults.
Reboot: Press the button once.
Factory default: Press and hold the button for at least 10
seconds.
•RJ45 Ethernet connector: The RJ45 Ethernet port is for 10/100
Mbps network transmission.
•5-pin terminal block connector for DI/Relay: The VPort 66-2MP
supports 1 DI (digital input) and 1 relay output.
Relay
Output
N.C.
(normal close)
Max. 1 A, 24 VDC
Initial status is
Normal Open
COM (common)
NO
(normal open)
DI DI: I+
High:
+13 V to +30 V
Low:
-30 V to +3 V
GND:
⊥
•4-pin terminal block for audio input/output: The VPort 66-2MP
supports 1 audio input and 1 audio output for an external microphone
and external speaker.
Audio input
IN +
Audio input +
IN -
Audio input -
Audio output
OUT -
Audio output -
OUT +
Audio output +
•Grounding: Attach the grounding cable with attachment ring to the
mounting kit’s grounding screw (inside the mounting kit box) to
ground the VPort 66-2MP.

- 7 -
•Safety Rope: For easier installation, use the safety rope to hook the
camera to the mounting kit buckle.
Hardware Installation
A mounting kit is required to install the VPort 66-2MP. Below we use the
VP-520LB to illustrate; the installation method of other accessories is
similar.
Step 1: Open and remove the top cover.
Use the security torx to loosen the 4 top cover screws.
Step 2: Installing an SD card requires removing the camera
module.
1. Loosen the 2 anti-drop Phillips screws, which hold the camera
module in place.

- 8 -
2. Pull the camera module a little and turn it clockwise to remove the
camera module from the camera module connector.
3. Insert the SD card, and then install the camera module by rotating
the camera module connector counterclockwise. Screw in the 2
anti-drop Phillips screws.
NOTE
If you have difficulty removing the camera module from the
camera module connector,
position the camera module in a
downwards direction. Doing so will make it easier to turn the
camera module clockwise.
Step 3: Install the sunshield (VP-SH1) if required
The VP-SH1 sunshield can be used with the VPort 66-2MP to prevent
direct sunlight from shining on the housing. Using the sunshield could be
warranted since sunlight can affect the heat dissipation mechanism.
1.
Loosen the 4 security screws
on the top of the camera.

- 9 -
2. Remove the black mount kit
and put the VP-SH1 on the
housing. Use the 3 small
Phillips screws in the
VP-SH1’s package to fix the
VP-SH1 to the housing.
3. Replace the black mount kit
tighten the 4 security screws
.
Step 4: Fasten the dry bag inside the housing
Use the hook-and-loop fastener to attach the dry bag to the camera
housing.
1.
Remove the dry bag from the package stick it
to the hook fastener.
2.
Attach the other side of the hook fastener to
the internal wall of the camera housing. Be
sure not to place
the dry bag on top of the 2
Phillips screws since the dry bag
will block the
way when removing the camera module.

- 10 -
Step 5: Close the top cover and screw in the 4 top cover screws
immediately (5.5 kgf-cm torque is recommended)
NOTE
The dry bag will absorb moisture inside the camera to prevent
m
oisture from condensing on the inside of the
transparent dome
when
the camera is used in low temperature environments.
Install the dry bag and replace the camera’s top cover
immediately after o
pening the dry bag and exposing it to the
atmosphere.
Step 6: Install the VPort 66-2MP on the VP-520LB mounting kit
1. Loosen the 3 socket set screws on the VP-520LB tube.
2. Loosen the 4 Phillips screws on the front cover, the stud bolts inside
the front cover, and the ground screw inside the box, and then pull
the bolt from the hinge to separate the front cover and the box.

- 11 -
3. Insert the VPort 66-2MP’s external cables and connectors through
the tube.
4. Connect the connectors.
5.
Arrange the cables and connectors
inside the box and then fix the ground
screw and hook the safety
rope with the
buckle. Close the front cover, put the
stud bolt back on the hinge to fix it in
place, and then tighten
the 4 front cover
Phillips screws.
6. Once the VPort 66-2MP is installed on the VP-520LB, you can install
the VPort 66-2MP+VP-520LB to a wall or on a pole (with the
VP-510CPM).
With sunshield
Without sunshield
NOTE
Refer to the mounting kit installation guide for detailed
information about the accessories included with the mounting kit.

- 12 -
Step 7: Power on the VPort 66-2MP
NOTE
When the VPort 66-2MP’s internal temperature is under -30°C, it
will need at least 30 to 40 minutes to power up.
Software Installation
Step 1: Configure the VPort’s IP address.
When the VPort 66-2MP is first powered on, the POST (Power On Self Test)
will run for a few moments (about 90 to 120 seconds). The network
environment determines how the IP address is assigned.
DHCP Server Network Environment
For this type of network environment, the unit’s IP address will be
assigned by the network’s DHCP server. Refer to the DHCP server’s IP
address table to determine the unit’s assigned IP address. You may also
use the Moxa VPort and EtherDevice Configurator Utility (edscfgui.exe),
as described below:
Using the Moxa VPort and EtherDevice Configurator Utility
(edscfgui.exe)
1. Run the edscfgui.exe program to search for the VPort. After the
utility’s window opens, you may also click on the Search button
to initiate a search.
2. When the search has completed, the Model Name, MAC address, IP
address, serial port, and HTTP port of the VPort will be listed in the
utility’s window.
3. Double click the selected VPort or use the IE web browser to access
the VPort’s web-based manager (web server).
Non DHCP Server Network Environment
If your VPort is connected to a network that does not have a DHCP server,
you will need to configure the IP address manually. The default IP address
of the VPort is 192.168.127.100 and the default subnet mask is
255.255.255.0. Note that you may need to change your computer’s IP
address and subnet mask so that the computer is on the same subnet as
the VPort.
To change the IP address of the VPort manually, access the VPort’s web
server, and then navigate to the System Configuration Network 
General page to configure the IP address and other network settings.
Check the Use fixed IP address to ensure that the IP address you
assign is not deleted each time the VPort is restarted.

- 13 -
Step 2: Accessing the VPort’s web-based manager.
Type the IP address in the web browser’s address input box and then
press enter.
Step 3: Install the ActiveX Control Plug-in.
A security warning message will appear the first time you access the
VPort’s web-based manager. The message is related to installing the
VPort AcitveX Control component on your PC or notebook. Click Yes to
install this plug-in to enable the IE web browser for viewing video images.
NOTE
For Windows XP SP2 or above operating systems, the ActiveX
Control component will be blocked for system security reasons.
In this case, the VPort’s security warning message window may
not appear
, and you will need to unlock the ActiveX control
blocked function or disable the security configuration to en
able
the installation of the VPort’s ActiveX Control component.
Step 4: Access the VPort P66-2MP’s web-based manager
homepage.
After installing the ActiveX Control component, the homepage of the
VPort 16’s web-based manager will appear. Check the following items to
make sure the system was installed properly:
1. Video Images
2. Video Information
3. Click the Show PTZ Control Panel button; the PTZ Camera Control
pop-up window should appear.

- 14 -
Step 5: Access the VPort’s system configuration.
Click on System Configuration to access the system configuration
overview to change the configuration. Model Name, Server Name, IP
Address, MAC Address, and Firmware Version appear in the green
bar near the top of the page. Use this information to check the system
information and installation.
For details of each configuration, check the User’s Manual on the software
CD.
Wiring Requirements
ATTENTION
Safety First!
•
Be sure to disconnect the power cord before installing and/or
wiring your Moxa VPort 66-2MP.
•
Calculate the maximum possible current in each power wire
and common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
•
If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment.
You should also pay attention to the following:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
•Keep input wiring and output wiring separated.
•It is strongly advised that you label wiring to all devices in the system
when necessary.

- 15 -
Grounding the VPort 66-2MP
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
Dimensions (mm/inch)
Side View
Bottom View