Moxa Technologies V2201 User manual

P/N: 1802022010014
*1802022010014*
V2201 Series
Quick Installation Guide
Version 3.2, April 2022
Technical Support Contact Information
www.moxa.com/support
2022 Moxa Inc. All rights reserved.

- 2 -
Overview
The Moxa V2201 Series ultra-compact x86 embedded computer is
based on the Intel® Atom™ E3800 Series processor, features the most
reliable I/O design to maximize connectivity, and supports dual wireless
modules, making it suitable for a diverse range of communication
applications. The computer’s thermal design ensures reliable system
operation in temperatures ranging from -40 to 85°C, and wireless
operation in temperatures ranging from -40 to 70°C with a special
purpose Moxa wireless module installed. The V2201 Series supports
Proactive Monitoring funct io n for device I/O status monitoring and
alerts, system temperature monitoring and alerts, and system power
management. Closely monitoring the system status makes it easier to
recover from errors and provides the most reliable platform for your
applications.
Package Checklist
Before installing the V2201, verify that the package contains the
following items:
•V2201 embedded computer
•Terminal block to power jack converter
•Wall mounting kit
•Quick installation guide (printed)
•Warranty card
NOTE: Please notify your sales representative if any of the
above items are missing or damaged.
V2201 Panel Layout
The following figures show the panel layouts of the V2201-W models;
for “non-W” models, the five antenna connectors will not be installed
during production.
Front Panel

- 3 -
Right Panel
Left Panel
LED Indicators
The following table describes the LED indicators located on the front
panel of the V2201.
LED Name
Status
Function
Power
Green
Power is on and computer is functioning normally.
Off
Power is off
User
Defined
Red
Event has occurred
Off
No alert
mSATA Yellow Blinking: Data is being transmitted
Off
Not connected / No data transmission
SD Card
Yellow
Blinking: Data is being transmitted
Off
Not connected / No data transmission
Wireless 1
Green
Steady On: Link is On
Blinking: Data is being transmitted
Off
Not connected
Wireless 2
Green
Steady On: Link is On
Blinking: Data is being transmitted
Off Not connected

- 4 -
LED Name
Status
Function
LAN 1
Yellow
Steady On: 1000 Mbps Ethernet link
Blinking: Data is being transmitted
Green Steady On: 100 Mbps Ethernet link
Blinking: Data is being transmitted
Off
10 Mbps Ethernet link or LAN is not connected
LAN 2
Yellow
Steady On: 1000 Mbps Ethernet link
Blinking: Data is being transmitted
Green
Steady On: 100 Mbps Ethernet link
Blinking: Data is being transmitted
Off
10 Mbps Ethernet link or LAN is not connected
Tx 1
Green
Blinking: Data is being transmitted
Off
Not connected
Tx 2
Green
Blinking: Data is being transmitted
Off
Not connected
Rx 1
Yellow
Blinking: Data is being transmitted
Off
Not connected
Rx 2
Yellow
Blinking: Data is being transmitted
Off
Not connected
NOTE
The Mini PCIe card’s LED behavior depends on the module
Installing the Wireless Modules
ATTENTION
The
“-W” models (e.g., V2201-E2-W-T) come with a heat sink
for the cellular card and five wireless SMA connectors installed.
The V2201 has two Mini PCIe sockets on the rear panel. One socket
only supports USB signals using the MC9090, MC7354, or MC7354
Mini PCIe cards. The other socket supports standard USB and PCIe
signals.
STEP1: Loosen the four screws
located at the middle of the rear
panel and open the cover.
STEP 2: Insert the wireless module
card at an angle.
STEP 3: Push the wireless module
card down and fasten it with the
two screws included with the
product.
The V2201 has the following two Mini PCIe sockets.

- 5 -
Socket 1: USB signal, for 3G/LTE
Mini PCIe card (Sierra Wireless
MC9090, MC7304, or MC7354).
NOTE: The cellular card heat
sink is installed in socket 1.
Socket 2: Standard USB + PCIe
signals, for Wi-Fi Mini PCIe card
(SparkLAN WPEA-252NI).
STEP 4: Connect the corresponding
wireless module cards to
connectors of the Mini PCIe
sockets.
The following five connectors are
available:
No. 1 & No. 3:
For the Wi-Fi Mini PCIe card
No. 2 & No. 4:
For the 3G/LTE Mini PCIe card
No. 5:
For the GPS module
STEP 5: Replace the rear cover.
You can also purchase and install external 3G, 4G, and Wi-Fi antennas
from Moxa. Contact a Moxa sales representative for information.
After installing the wireless modules and wireless external antennas,
the computer should appear as follows:
Installing the V2201
DIN-rail Mounting
The DK-DC50131 die-cast metal kit (shipped only with V2201-E4-W-T-
LX; purchase separately for all other models), enables easy and robust
installation of the V2201. Use the six M4*6L FMS screws included to
attach the DIN-rail mounting kit to the side panel of the V2201.

- 6 -
Installation:
STEP 1:
Insert the upper lip of the DIN rail into
the DIN-rail mounting kit.
STEP 2:
Press the V2201 towards the DIN rail
until it snaps into place.
Removal:
STEP 1:
Pull down the latch on the
mounting kit with a screwdriver.
STEP 2 & 3:
Use the screwdriver to pry the
V2201 slightly forward
away from
the DIN rail, and then lift the
V2201 upwards to remove it from
the DIN rail.
STEP 4:
Press the recessed button on the spring-
loaded bracket to lock it into position until
the next time you need to install the
V2201 on to a DIN rail.
Wall or Cabinet Mounting
The V2201 computers (with the exclusion of the V2201-E4-W-T-LX
model) come with two metal brackets for attaching to a wall or the
inside of a cabinet. Four screws (Phillips truss-headed M3*6L nickel
plated with Nylok®) are included in the kit.
Step 1:
Use two screws for each
bracket and attach the bracket
to the rear of the V2201.

- 7 -
Step 2:
Use two screws on each side to
attach the V2201 to a wall or
cabinet.
The product package does not
include the four screws required
for attaching the wall-
mounting
kit to the wall or cabinet; they
need to be purchased
separately. We r ecommend
using standard M3*5L screws.
ATTENTION
This equipment is intended to be used in Restricted Access
Locations, such as a computer room, with
access limited to
SERVICE PERSONAL or USERS who have
been instructed on
how to handle the metal
chassis of equipment that is so hot
that special protection may be needed before touching it. The
location should only be accessible with a key or through a
security identity system.
Connector Description
Power Connector
Connect the 9 to 36 VDC LPS or Class 2 power line to the V2201’s
terminal block. If the power is supplied properly, the Power LED will
light up. The OS is ready when the Ready LED glows a solid green.
ATTENTION
The power cord of
the adapter should be connected to a socket
outlet with earthing connection.
ATTENTION
This product is intended to be supplied by a Listed Power
Adapter or DC power source, output rated 9 to 36 VDC, 3.5 to 1
A minimum, Tma = 85 degree C minimum.
Grounding the V2201
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from
the grounding screw (M4) to the grounding surface prior to connecting
the power.

- 8 -
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface, such as a metal panel.
SG: The Shielded Ground (sometimes called
Protected Ground)
contact is the right most
one
on the
3-pin power terminal block connector
when viewed from the angle shown here.
Connect the SG wire to an appropriate
grounded metal surface.
HDMI Outputs
The V2201 comes with a type A HDMI female connector on the front
panel to connect an HDMI monitor.
The screw hole above the HDMI connector is used to attach a custom
lock to the HDMI connector; a custom lock is needed since the shape of
different HDMI connectors are not the same. Please contact a Moxa
sales representative for details.
Before Attaching the Lock
After Attaching the Lock

- 9 -
Ethernet Ports
The 10/100/1000 Mbps Ethernet ports use RJ45 connectors.
Pin
10/100 Mbps
1000 Mbps
1
ETx+
TRD(0)+
2
ETx-
TRD(0)-
3
ERx+
TRD(1)+
4
–
TRD(2)+
5
–
TRD(2)-
6
ERx-
TRD(1)-
7
–
TRD(3)+
8
–
TRD(3)-
Serial Ports
The serial ports use DB9 connectors. Each port can be configured by
software for RS-232, RS-422, or RS-485. The pin assignments for the
ports are shown in the following table:
Pin RS-232 RS-422
RS-485
(4-wire)
RS-485
(2-wire)
1
DCD
TxDA(-)
TxDA(-)
–
2
RxD
TxDB(+)
TxDB(+)
–
3
TxD
RxDB(+)
RxDB(+)
DataB(+)
4
DTR
RxDA(-)
RxDA(-)
DataA(-)
5
GND
GND
GND
GND
6
DSR
–
–
–
7
RTS
–
–
–
8
CTS
–
–
–
SD Slot
The V2201 has an SD slot for storage expansion. The SD slot allows
users to plug in an SD 3.0 standard SD card. To install an SD card,
gently remove the outer cover from the left, and then insert the SD
card into the slot.
USIM Slot
The V2201 has a USIM slot for 3G/LTE wireless Internet connections.
To install a USIM card, gently remove the outer cover from the left, and
then insert the USIM card into the slot.
USB Hosts
The V2201 has 1 USB 3.0 and 2 USB 2.0 Type-A connectors. 2 USB 2.0
ports are located on the front panel, and 1 USB 3.0 port is on the right
panel. The port supports keyboard and mouse and can also be used to
connect a Flash drive for storing additional data.
Audio Interface
The audio output of the V2201 is combined with the HDMI connector.

- 10 -
DI/DO
The V2201 comes with four digital inputs and
four digital outputs on a 2 x 5 terminal block.
Reset Button
Press the “Reset Button” on the left side panel of the V2201 to reboot
the system automatically.
Real-time Clock
The V2201’s real-time clock is powered by a lithium battery. We
strongly recommend that you do not replace the lithium battery without
help from a qualified Moxa support engineer. If you need to change the
battery, contact the Moxa RMA service team.
ATTENTION
There is a risk of explosion if the battery is replaced by an
incorrect type of battery.
Powering on the V2201
To power on the V2201, connect the “terminal block to power jack
converter” to the V2201’s DC terminal block (located on the side
panel), and then connect the 9 to 36 VDC power adapter. The computer
is automatically switched on once the power adapter is plugged in. If it
does not, press the Power Button to turn on the computer. Note that
the Shielded Ground wire should be connected to the top pin of the
terminal block. It takes about 30 seconds for the system to boot up.
Once the system is ready, the Power LED will light up.
Connecting the V2201 to a PC
Power on the V2201 computer after connecting a monitor, keyboard,
and mouse, and verifying that the power source is ready. Once the
operating system boots up, the first step is to configure the Ethernet
interface. The factory default settings for the V2201’s LANs are show
below (W7E uses DHCP).
Default IP Address
Netmask
LAN 1
192.168.3.127
255.255.255.0
LAN 2
192.168.4.127
255.255.255.0