MSW Miniac Double Wireless CC-317 User manual

26375 2/18 | 85-000870_INST_B
MINIAC DOUBLE WIRELESS CC-317 CYCLING COMPUTER INSTRUCTIONS
6400 WEST 105TH STREET // BLOOMINGTON, MN 55438 // 1-855-883-6563 // WWW.MSWBIKE.COM
Thank you for purchasing an MSW®Miniac Double Wireless CC-317
Cycling Computer! At MSW®we believe that having essential accessories
makes a good ride great.
WARNING: Cycling can be dangerous. Bicycle products should
be installed and serviced by a professional mechanic. Never modify your
bicycle or accessories. Read and follow all product instructions and warnings
including information on the manufacturer’s website. Inspect your bicycle
before every ride. Always wear a helmet.
WARNING: Please read over the following information before using the
MSW Miniac Double Wireless CC-317 Cycling Computer.
• Never use the cycling computer in combination with other medical/
implanted electronic equipment and devices (especially heart pacemakers,
EKG equipment, TENS equipment, cardio-pulmonary machines, or
pacemakers). If you are severely ill or pregnant, please consult your doctor
before using cycling computer. Keep this device away from children.
It contains batteries, which might be swallowed by children.
• As is the case most wireless electronic devices, there can sometimes be
interference that causes inaccurate display readouts. Avoid using your
cycling computer near common sources of interference like high voltage
power lines, air conditioning motor units, fluorescent lights, wristwatches,
mobiles, and some other computers.
For additional product and safety information go to: www.mswbike.com/safety.
COMPATIBILITY
The Miniac Double Wireless CC-317 Cycling Computer. is compatible with MSW
Speed and Cadence Sensor CC-314.
INCLUDED PARTS
Please check that all the following items have been included with the cycle
computer before starting.
A CC-317 cycling computer
B Sensor
C Cadence magnet
D White stabilizing pad
for cadence magnet
E Black stabilizing pad for sensor
F 6 nylon zip ties
G Mounting bracket
H. Rubber shim
I. Wheel magnet
INSTALLATION
MOUNTING THE HANDLEBAR BRACKET
Fit the rubber pad to the back of the handlebar bracket and use the nylon ties
to attach it to the bar. Do not fully tighten the nylon ties until you’re certain the
angle of the computer is correct. (figs 1, 2).
Place the cycle computer on the bracket and secure it by turning clockwise
(fig 3).
MOUNTING THE SENSOR
The sensor is mounted on the non-driveside chainstay, just behind the bottom
bracket. The distance between the computer head unit at the handlebar and
the sensor should not exceed 150cm.
The larger part of the sensor reads the crank arm magnet to register cadence,
etc. The adjustable arm of the sensor unit registers speed, distance, etc.
The larger part of the sensor faces the front of the bike, and the adjustable arm
faces the back and sits along the inside of the chainstay. Loosen the knurled
dial in front of the adjustable arm to rotate it in the optimal position (fig. 4).
Do not tighten it until the optimal position has been determined.
Rubber Pad
Bracket
Cycle Computer
Bracket
Nylon Ties
Figure 1 Figure 2
Figure 3
Figure 4
A B C D E
F G H I

26375 2/18 | 85-000870_INST_B
MINIAC DOUBLE WIRELESS CC-317 CYCLING COMPUTER INSTRUCTIONS
6400 WEST 105TH STREET // BLOOMINGTON, MN 55438 // 1-855-883-6563 // WWW.MSWBIKE.COM
Place the included rubber pad between the sensor and the chainstay.
The sensor is attached using two included zip ties, but do not fully tighten
them until the wheel and crank arm magnets are in place, and the adjustments
that yield the best readings are made between the sensor, sensor arm, and the
magnets (fig. 5).
The distance between the crank arm magnet and the sensor, and between
the rear wheel magnet and the sensor arm should not exceed 3mm.
MOUNTING THE CRANK AND WHEEL MAGNETS
1. Place the crank arm magnet on the inside of the crank arm 2 to 3cm up the
arm from the pedal spindle and zip tie it in place.
2. Position the larger part of the sensor close enough to the crank arm that the
required distance between it and the crank arm magnet is achieved (fig. 6).
3. Using this sensor placement as a guide, position the wheel magnet in the
approximate area that it will pass the sensor arm on the inside of the
chainstay. The wheel magnet is tightened to the spoke by threading
it into the magnet bracket that sits behind the spoke (fig. 7).
4. Holding the larger part of the sensor in place with one hand, rotate the arm
of the sensor so that the required distance between it and the wheel
magnet is achieved.
5. Use two zip ties to tighten the sensor to the chainstay, and snip off the
excess length.
6. Make any final adjustments to the sensor arm to achieve the required
distance between it and the wheel magnet, and tighten the knurled dial.
7. Test to make sure that the magnets are activating the sensor, and the
computer head unit is registering the magnets as they pass the sensor.
WHEEL SIZE CHART
CALCULATING WHEEL CIRCUMFERENCE
To get the most accurate speed and distance data, the wheel size must
be correct. Mark the tire or position the valve stem at the 6 o’clock position
and push the bike until the mark or valve
stem is back to 6 o’clock. Then measure
the length between two points to get the
circumference.
Refer to the wheel size chart for diameter
and tire width. If your wheel and tire size
is not listed, use the following wheel
circumference equation:
Circumference (mm) = 2 x 3.14 x R (inch) x 2.54
(1 inch = 2.54cm), R = radius in centimeters.
Figure 5
1–3mm
1–3mm
Spoke
Chainstay
(non-driveside)
Rear
Wheel
Front
Wheel
Cadence Sensor Speed Sensor
Zip Tie Cadence Magnet
Crank Pedal
Cadence Sensor
1–3mm
Figure 6
Figure 7
Tire Scale L (mm)
14 x 1.50" 1020
14 x 1.75 1055
16 x 1.50 1185
16 x 1.75 1195
18 x 1.50 1340
18 x 1.75 1350
20 x 1.75 1515
20 x 1-3/8 1615
22 x 1-3/8 1770
22 x 1-1/2 1785
24 x 1 1753
24 x 3/4 Tubular 1785
24 x 1-1/8 1795
24 x 1-1/4 1905
24 x 1.75 1890
24 x 2.00 1925
24 x 2.125 1965
26 x 7/8 1920
26 x 1 (59) 1913
Tire Scale L (mm)
26 x 1 (65) 1952
26 x 1-1/8 1970
26 x 1-3/8 2068
26 x 1-1/2 2100
26 x 1.40 2005
26 x 1.50 2010
26 x 1.75 2023
26 x 1.95 205
26 x 175 2023
26 x 1.95 2050
26 x 2.00 2055
26 x 2.10 2068
26 x 2.125 2070
26 x 2.35 2083
26 x 3.00 2170
27 x 1 2145
27 x 1-1/8 2155
27 x 1-1/4 2161
27 x 1-3/8 2169
Tire Scale L (mm)
27.5 x 2.10 2170
27.5 x 2.30 2202
29 x 2.10 2288
29 x 2.30 2326
650 x 35A 2090
650 x 38A 2125
650 x 38B 2105
700 x 18C 2070
700 x 19C 2080
700 x 20C 2086
700 x 23C 2096
700 x 25C 2105
700 x 28C 2136
700 x 30C 2146
700 x 32C 2155
700c Tubular 2130
700 x 35C 2168
700 x 38C 2180
700 x 40C 2200

26375 2/18 | 85-000870_INST_B
MINIAC DOUBLE WIRELESS CC-317 CYCLING COMPUTER INSTRUCTIONS
6400 WEST 105TH STREET // BLOOMINGTON, MN 55438 // 1-855-883-6563 // WWW.MSWBIKE.COM
MAIN DISPLAY AND BUTTON FUNCTIONS
SET MODE
From any screen, press the SET button for three seconds to go into setting
mode (fig. 8).
Press the MODE button for three seconds to save any changes and exit.
RESET
Press and hold the C (Clear) button for three seconds to reset the data (fig. 9).
In the Average Speed screen, if the trip time is more than 29:59:59 or the
distance is more than 999.99 miles/kilometers, you will receive an error
message and the data will need to be reset.
MODE CHANGE
Press the Mode button or C button to change modes (fig. 10).
Unit Tire size
Time
Time
Gender / Weight ODO Temperature
Gender / Weight
M (MODE): Next option
C: Next setting
[SET]: Change the value
Temperature °C/°F
H1 (Male)
H2 (Female)
WS: 0100–2999mm
KM/H+Kg+KM
M/H+Lb+KM
12H/24H
[SET]
Weight: 20–150Kg
44–330 lb
M M
C
M/CM/C
M/C
M/CM/C
[SET][SET]
C
M/C Save and Exit
Hour (1–24)
Minute (0–59)
Second (0–59)
>M
[SET]
Figure 8
Temperature
Motion Signal
Mode Indicator
Sub-Display
Current Speed
AM/PM Indicator
SET BUTTON
Speed Scale
MODE BUTTON / BACKLIGHT
(Press 2 seconds to
turn on backlight
CLEAR(C) / RESET / OFF
3 seconds
Figure 9
Time Average Speed Maximum Speed Distance
Odometer Calorie Consumption
Average Cadence Maximum Cadence Trip Cadence
C BUTTON
MODE BUTTON
M
M
M
MMM
C C
C
Figure 10

26375 2/18 | 85-000870_INST_B
MINIAC DOUBLE WIRELESS CC-317 CYCLING COMPUTER INSTRUCTIONS
6400 WEST 105TH STREET // BLOOMINGTON, MN 55438 // 1-855-883-6563 // WWW.MSWBIKE.COM
PAIRING THE COMPUTER WITH THE SENSOR
In any mode, press the M and C buttons, and hold for six seconds.
Press the C button. The computer will search for 30 seconds. The sensor
should be paired after 5 seconds. If it is not paired check that the sensor and
magnets are aligned; also check the battery (fig. 11). Press and hold the
Mode button for three seconds to exit.
AUTO WAKE UP AND SLEEP
Auto Wake Up: The computer will “wake up” with any vibration or speed reading.
Auto Sleep: After six minutes with no vibration or speed, the computer will
enter “sleep” mode.
Deep Sleep: If the sequence of Auto Wake and Auto Sleep repeats five times,
the computer will enter “Deep Sleep” mode. Either button on the front of the
computer will need to be pressed to wake the unit up.
BACKLIGHT
In any mode, press the Set button or press and hold Mode button for two
seconds to turn on the backlight.
TROUBLESHOOTING
Q1. Display is black or very light:
The battery power may be low. Make sure the battery is installed correctly
or replace if necessary.
Q2. Display becomes dark or black:
The unit is too hot. Place the unit in a shaded area and it will return to normal.
Q3. The unit operates slowly or struggles:
The unit is too cold. Warm the unit and it will return to normal.
Q4. Data in display varies enormously:
Check the surroundings for electromagnetic or high energy interference,
e.g. power lines, and move away from the source of interference.
Q5. Data in display shows slowly:
The unit may be too cold. When the temperature rises, the data reading will
return to normal.
Q6. Current speed does not appear
The sensor may be too far from the magnet. Make sure the gap is no wider
than 3mm. Make sure the magnet is free of corrosion. Make sure the sensor
battery is installed correctly or replace if necessary.
IMPORTANT HEALTH NOTICE!
Please read over the following information before using the Cycle Computer.
• Never use the cycle computer in combination with other medical/implanted
electronic equipment or devices (especially heart pacemakers, EKG
equipment, TENS equipment, cardio-pulmonary machines, or packemakers)
• If you are severely ill or pregnant, please consult your doctor before using
the cycle computer
• Keep this device away from children. It contains batteries, which may
be swallowed by children
• As with most electronic receiving devices, there can sometimes be
interference that causes inaccurate display readouts. Avoid using your cycle
computer near common sources of interference. These include high voltage
power lines, air conditioning motor units, fluorescent lights, wristwatches,
mobile phones, and computers
SPECIFICATIONS
MAINTENANCE
If the display contrast changes and figures become faint, it’s time to replace
the battery. Consider changing the computer sensor and transmitter batteries
at the same time.
NOTE: Do not expose the computer to extremely cold or hot temperatures
i.e. don’t leave the unit in direct sunlight for extended periods of the time.
SENSOR
Check the position of sensor and magnet periodically. Rust or corrosion on the
magnet may cause malfunction. The gap between magnet and sensor cannot
exceed 3mm.
BRACKET / MAGNET / SENSOR BAND
These items can be wiped with a damp rag or mild soap solution.
Operating Temp 32–104°F (0–40°C)
Storage Temp 14–122°F (-10–50°C)
Battery (computer and sensor) 3V Lithium CR2032
Battery life (computer) ~1 yr (1 hr/day use)
Computer Weight 23g
Sensor Weight 20g
Timer Range 29 (hour) : 59 (minute) : 59 (second)
Current Speed Range 0~99.9kph / 0~62.4 mph
Average Speed Range 0~99.9kph / 0~62.4 mph
MAX Speed Range 0~99.9kph / 0~62.4 mph
(Trip) Distance Range 0~999.99km / 0~624.99 mi
Odometer Range 0~99999km / 0~62499 mi
Searching for 30 seconds
Press and hold mode
key for 3 seconds
After 5 seconds of receiving
code from the sensor
PAIRED NOT PAIRED
C
PRESS
Not paired:
• Check sensor alignment
• Check battery
Figure 11

26375 2/18 | 85-000870_INST_B
MINIAC DOUBLE WIRELESS CC-317 CYCLING COMPUTER INSTRUCTIONS
6400 WEST 105TH STREET // BLOOMINGTON, MN 55438 // 1-855-883-6563 // WWW.MSWBIKE.COM
BATTERY REPLACEMENT
COMPUTER
The battery symbol in the top left corner of the screen will appear when the
battery is running low. Unscrew the back cover. The (+) side should be facing
up. Gently remove the battery and replace it with a new battery model CR2032.
SENSOR:
A red light on the sensor will appear when its battery is running low. Unscrew
the back cover. The (+) side should be facing up. Gently remove the battery and
replace it with a new battery model CR2032.
BATTERY WARNINGS
A coin-cell, lithium-ion battery is used in this device. If these guidelines are not
followed, batteries may experience a shortened lifespan or may present a risk
of damage to the device, fire, chemical burn, electrolyte leak, and/or injury.
• Do not leave the device exposed to a heat source or in a high-temperature
location, such as in the sun in an unattended vehicle. To prevent the
possibility of damage, remove the device from the vehicle or store it out
of direct sunlight, such as in the glove box
• Do not disassemble, modify, remanufacture, puncture or damage the device
or batteries
• Do not immerse or expose the device or batteries to water or other liquids,
fire, explosion, or other hazard
• Do not use a sharp object to remove the batteries
• KEEP BATTERIES AWAY FROM CHILDREN
• NEVER PUT BATTERIES IN MOUTH. Swallowing can lead to chemical burns,
perforation of soft tissue, and death. Severe burns can occur within two
hours of ingestion. Seek medical attention immediately
• Replaceable coin-cell batteries may contain perchlorate material. Special
handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
• Only replace batteries with correct replacement batteries. Using other
batteries presents a risk of fire or explosion
• Do not operate the device outside of the temperature ranges specified
in these instructions
• Contact your local waste disposal department to dispose of batteries
in accordance with applicable local laws and regulations
LIMITED 2-YEAR WARRANTY
MSW warrants this new MSW product against defects in materials and
workmanship for two (2) years from the original date of retail purchase
by the consumer. This limited warranty is expressly limited to the repair
or replacement of the original product, at the option of MSW, and is the
sole remedy of the warranty. This limited warranty applies only to the
original purchaser of the MSW product and is not transferable.
In no event shall MSW be liable for any loss, inconvenience or damage,
whether direct, incidental or consequential or otherwise resulting from breach
of any express or implied warranty or condition of merchantability, fitness for
a particular purpose, or otherwise with respect to this product except as set
forth herein. This warranty gives the consumer specific legal rights, and those
rights and other rights may vary from state to state.
This warranty does not cover the following:
• Damage due to improper assembly or follow-up maintenance or lack
of skill, competence or experience of the end user
• Products that have been modified, neglected, used in competition or for
commercial purposes, misused or abused, involved in accidents or anything
other than normal use
• Damage or deterioration to the surface finish, aesthetics or appearance
of the MSW product
• Normal wear and tear
• Labor required to remove and/or refit and re-adjust the product within
the bicycle assembly
• Installation of components, parts, or accessories not originally intended
use with or compatible with MSW products
TO THE EXTENT NOT PROHIBITED BY LAW, THESE WARRANTIES ARE
EXCLUSIVE AND THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES
OR CONDITIONS INCLUDING WARRANTIES OR CONDITIONS OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
WARRANTY PROCESS
If you and your shop think your MSW product is worthy of a warranty
inspection, please return the product to the original place of purchase,
accompanied by a sales receipt.
For complete warranty information, visit www.mswbike.com/safety/warranty.