Myride E SCOOTER ES9001 User manual

Electric Scooter
E SCOOTER ES9001

1
1
Table of Contents
1. The electric scooter and main parts ............................. 2, 3
2. Folding and unfolding..................................................... 4, 5
3. Display and functions...................................................... 6
4. Trouble Shooting …………………………….……..…. 7
5. Charging .......................................................................... 8
6. Specifications ................................................................... 9
7. Safety instructions ............................................................. 10
8. Care and Storage ................................................................ 11
9. Maintenance………………………………………………12
10. Warranty………………………………………………….13
11. Declaration………………………………………………..14
12. Contact us…………………………………………………15
.

2
2
I The ESCOOTER ES9001 main parts
1
2
3
4
5
6
7
14
8
9
10
11
15
12
13

3
3
1.Foldiung handlebar
2.Adjustable pole
3.Quick release
4.Head Light
5.Safety buckle
6.Folding Lock
7.Front suspension fork
8.Deck
9.Anti-slip sticker
10.Battery Case
11.Rear Suspension
12.Motor
13.Rear Light
14.Front Mudguard
15.Rear Mudguard
Folding Handlebar
1. Brake lever
2. Grip
3. Bell
4. Light Switch button
5. handlebar Sleeve
6. Connector for handlebar and pole
7. Display
8. Switch button
9. Mode Button
1
3
6
7
8
1
2
9
5
5
4
2

4
4
2 Folding and unfolding
1. Unfolding
When you take the electric scooter out from the carton, it is almost completely assembled, just
unfold the stem and handlebar, to fully expand the electric scooter.
1.1 How to unfold the stem?
Firstly, release the safety buckle.
Secondly, press the folding lock.
Thirdly, keep pressing the folding lock and pull up the stem to the correct position until you
hear a “click “sound.
Finally, lock the safety buckle to fix the stem into position.
1.2 How to unfold the handlebar?
After unfolding the stem, please unfold the handlebar to expand the ESCOOTER ES9001
scooter completely.
Pull down the handlebar sleeve and then lift the left and right handlebar to the horizontal
position, then rotate the right-side handlebar sleeve clockwise to fix the right-side handlebar,
then rotate the left side handlebar anticlockwise to fix the left side handlebar.
To adjust the height of the stem, just loosen the quick release lever, pull up or push down the
upper part of the adjustable stem to the right height, then fix the quick release into position.
You have now expanded your ESCOOTER ES9001 completely and it is now ready for use.
2. Folding
If you need to fold your electric scooter for convenient transporting or storage, please refer to
the following to fold the handlebar then the stem.
2.1 How to fold the handlebar?
Loosen the right-side handlebar sleeve by rotating it anticlockwise till it is completely loose,
then pull out the right-side handlebar and fold it.
Loosen the right-side handlebar sleeve by rotating it clockwise till it is completely loose and
then pull out the left side handlebar and fold it.

5
5
2.2 How to fold the stem?
To fold the stem when the handlebar is folded.
Firstly, release the safety buckle.
Secondly, press the folding lock with your thumb on one hand while pushing the stem ahead
with another hand, to unlock the folding mechanism, then put down the stem slowly and
softly till hearing a “clicking” sound. Now the stem is folded and locked, you can now carry it
with one or two hands.
To fold the stem when handlebar is unfolded.
Firstly, release the safety buckle.
Secondly, hold the grips with two hands.
Thirdly, press down the folding locking mechanism with your foot while pushing the
handlebar forward then push down the stem slowly and softly till hearing “clicking” sound.
Now the stem is folded and locked completely by the folding mechanism.
3 Functions and application
1. Lights
When the display is switched on press the light switch button to turn on the front and rear
lights, press again to turn off.
2. Brake
The ESCOOTER ES9001 has front and rear drum brakes as well as an electric brake
system.
Pull left side brake lever to activate the electric brake and rear drum brake.
Pull right side brake lever to activate the electric brake, as well as the rear wheel and front
wheel mechanical brakes.

6
6
3. Display
1. Power switch button 2. Mode button
There are two buttons on the display, a power button and mode button.
3.1 Usage of display
Press and hold the power switch button to power on the electric scooter, once switched on, the
screen of display will show speed mode (1, 2 or 3), battery capacity, constant speed, trip or
DOD（depending on the function chosen). Press and hold the power switch again to switch off
the electric scooter.
If there is no input signal received within 3 minutes after switching it on, the display will be
switched off automatically.
After each short press of the power switch button, the following modes will be displayed
TRIP, DOD, VOL (battery volume) and time will be shown in turn.
Long press mode button to clear data of TRIP
Short press mode button to change speed mode between 1, 2 and 3.
Speed mode 1 is slow speed, mode 2 is middle speed and mode 3 is fast speed.
Pull finger throttle on the display to start riding.
Power Switch
Button
Mode Button
Finger Throttle

7
7
3.2 Trouble shooting
When your ESCOOTER ES9001 malfunctions, the display will show a certain code number
to let you know which area is faulty or causing a problem. The following fault codes are
indicated.
Code
Problem part
Signal
1
Brake
2
Motor
3
Throttle
4
Controller

8
8
4 Charging
Power off the electric scooter before charging.
Open the cover of the charging port.
Plug the output end of the charger into that charge port, which is under the deck, located on
the front / left side of the battery case. Then plug the input end of the charger into the power
point and switch on the power point for charging.
Red light is on when charging, when battery is fully charged, green light turns on.
After charging is complete, unplug the charger from the wall socket first then unplug from the
charging port on the scooter and finally cover the charging port with the rubber plug.
Charging Port
Charger

9
9
5 Specifications
Overall dimension
Unfolded: 112*58*119 cm
Folded: 112*20*46 cm
Frame
Al alloy
Tire
pneumatic, 9 inches
Suspension
Front and rear suspension
Brake
front and rear drum brake + electric brake
Motor
36V 200W rear drive motor
Battery
36V 12.8Ah, LG lithium battery
Charger
42V 2A
Charging time
6-8 H
Display
LCD
Speed mode
3 modes 10, 15, 25 km/h
Max Speed
25 km / h
Lights
front and rear lights + side flashing lights
loading capacity
100 kgs
Range per charge
40 km, depending on loading capacity and terrain
condition
N.W./G. W
19.65 kgs / 22.15 kgs
Packing:
113*21*43 cm

10
10
6 Safety instructions
1. It is not recommended driving in rain.
2. Please do not hang backpacks and other heavy objects on the handlebar.
3. It is illegal to leave or ride electric scooters on a highway, or ride at high speed.
4. It is illegal to ride an electric scooter on one foot.
5. It is not recommended to ride through puddles deeper than 2 cm.
6. Never ride an Electric scooter with more than one person on it.
7. Do not touch the brakes while riding or after stopping your ride, as they will be hot.
8. Do not ride your scooter by letting go of the handlebar.
9. Do not ride the electric scooter up or down steps or jump over obstacles.

11
11
7 Care and Storage
1. An Electric Scooter is only a device for enjoyment and commuting, however when you ride in
public areas, the electric scooter brings a certain amount of risk to yourself and others. For the
sake of your safety and others, you must strictly follow the instructions described in this manual,
as well as all local laws and requirements.
2. Please be aware, if you ride an electric scooter in public places, you must comply with all
recommendations for safety. Do not forget there is a possibility of collision due to pedestrians or
vehicles. There is also a risk of injury due to improper operation of the electric scooter. The
higher the speed the electric scooter goes, the longer the braking distance will be. On some
smooth roads emergency braking may cause skidding and slipping, the rider may lose their
balance and possibly fall. Therefore, when you are riding an electric scooter, you will need to be
vigilant, riding at a legal and safe speed and keep a safe distance from pedestrians and other
vehicles. When riding on unfamiliar terrain, be vigilant and take care.
3. While riding an electric scooter, please respect all pedestrians. Do not scare them, especially
children. Slow down when passing by them. If you are moving in the same direction as
pedestrians, try to stick to the left side as much as possible, if you are moving the opposite
direction, stick to the right and slow down.
4. Please strictly follow your country`s road rules when riding, as well as strictly abide by the
rules and recommendations in this manual. Violation of the above-mentioned rules and
recommendations may result in potential fines, personal injury, traffic accidents, legal disputes,
conflict, and other unpleasant situations. My E Ride will not bear any direct or joint liability or
be responsible in any way whatsoever if either of the above was to take place.
5. To avoid personal injury, do not allow any person who does not know how to ride an electric
scooter to ride it. Please teach the person before you allow the beginner how to ride the scooter,
and inform them to wear proper safety gear, especially a helmet which is a legal requirement.
6. Please inspect and check the electric scooter carefully before each use. If you find any
damaged parts, obvious low battery capacity, punctures, low tire pressures, any signs of
excessive wear, any unexpected sounds, abnormal symptoms, please stop using the electric
scooter immediately and ask for help from authorized My E Ride dealer.
8 Care and Storage
Clean and store electric scooter
If you find any dirt or water on the electric scooter housing, use a soft damp cloth to wipe it
off. You can use toothpaste and a toothbrush to clean the electric scooter stains and then
wipe it with a damp clean cloth.

12
12
Maintenance of electric scooter battery
1. Do not use batteries from other scooter brands to avoid a dangerous situation, as well as
void any warranty.
2. Do not open or disassemble the battery, as tis may cause an electric shock. Do Not to
touch any metal objects to avoid any short circuit. Otherwise, the battery may have
malfunction or even can injure the user.
3. It is recommended to use an AC adapter, which comes together with the electric scooter
from the factory, to avoid any accident of fire because of using non original adaptor.
4. Improper disposal of used batteries may cause severe environmental pollution. Please
dispose of batteries in accordance with local laws.
Please do not dispose of batteries together with waste food, protecting environment together!
5. After each use of the electric scooter, charge the battery to prolong its service life.
6. Do not store the battery in rooms at temperature exceed 50ºC or -20ºC (e.g., do not leave the
battery of electric scooter and other batteries in cars in the hot sun in summer). Do not place
the battery near fire. Otherwise, battery may deteriorate, overheat, and even can cause fire.
If the electric scooter will not be used in the following 30 days, charge the battery,
and keep the electric scooter in a cool and dry place. Every 60 days you need to
charge the battery, because battery will discharge automatically even the electric
scooter is not i n use. Any battery failure caused by not charging regularly is not
within warranty.
Not to let the battery discharge completely before you recharge it, which will extend battery
life. When using the electric scooter at normal room temperature, battery will be able to
perform much better and achieve much longer distance; but if you use the electric scooter at
temperatures below 0℃, performance and permeability decrease.
Note:
It is about 120-180 days for a fully charged battery to automatically discharge completely.
Please charge the battery in time before it discharged completely. The battery has a smart
chip, which stores information about its charging-discharging. If the battery is not charged
for a long time, it will discharge deeply and cause serious damage, which will make it
impossible to be recharged. Such failure is not included in warranty.
Caution:
Do not disassemble the electric scooter by unauthorized people, as there is a risk of electric
shock or serious injury as result of a short circuit)

13
13
9 Warranty
To ensure your E Scooter provides many years of trouble-free service, please
read the following as outlined by My E Ride and the Manufacturer. Please read
the following carefully.
I) GUARANTEE CONTENTS, TARGETS AND DEADLINE:
1. guarantee contents:
Purchase the unit from My E Ride or its authorized dealer. Operate according to
the instructions set in this manual and the manufacturer guarantees to rectify any
quality problems with its manufacturing or materials within the guarantee period.
2. Guarantee target and deadline: from the date of purchase
(1) One year guarantee for motor
(2) One year guarantee for battery
(3) The tires and other flexible parts are not covered by the guarantee.
II) GUARANTEE IS NOT ENSURED WITH THE PROBLEMS CAUSED BY
THE FOLLOWING:
(1) Do not operate according to the manual.
(2) Do not get maintenance from the specified dealers.
(3) Do not use the components or parts provided by My E Ride.
(4) Modify the unit or its part without authorization.
(6) The warranty has expired.
(7) Incidents caused by uncontrollable factors such as typhoon, floods, fire,
earthquake, or war.

14
14
Declaration
Manufacturer is not responsible for any incidental, indirect, special, or
consequential damages, including but not limited to the loss of profit, income or
data, due to the violation of explicit or implied warning or conditions mentioned
in this user manual or violation of local laws.
Note:
1) Please strictly follow the safety instructions in the manual. My E Ride is not
responsible for any financial losses, personal injuries, accidents, legal disputes,
and other conflicts of interest caused by operations that violate the user manual.
2) Always remember to insert the rubber plug into charging port after
charging., otherwise, the charging port may get wet, which will result in short
circuit of the charging port. The manufacturer will not be responsible for this
situation and will not offer free after-sales service for it.
3) Do not ride the scooter across deep holes or hit it against a hard surface,
which may break the folding mechanism. My E Ride will not be responsible for
this situation and will not offer free after-sales service for it, or any warranty.
4) Do not lift the rear fender when carrying the scooter, or it may break. My E
Ride will not be responsible for this situation should it occur. After folding the
electric scooter, please carry it by lifting the stem.
Warning:
Do not use alcohol, petrol, kerosene or other corrosive solutions, volatile chemical solvents
to clean the scooter. Otherwise, it will cause serious damage to the electric scooter body and
even cause the electronics to fail.
Do not wash the electric scooter with high pressure water. Make sure the electric scooter is
switched off when cleaning it. In addition, after charging the electric scooter, it is necessary
to insert the plug back into the charging port. Otherwise, it may be damaged.
If you do not use the electric scooter, store it in a dry and cool place. Do not leave it on the
street for long time. Leaving the electric scooter in the sun, or in extremely high or low
temperatures, can cause rapid aging of the body and wheels and even shorten the battery
service life.

15
15
Contact Us
If you have any questions about the E Scooter ES9001, please feel free to
contact My E Ride immediately.
Office: 03 8719 8358
Email: [email protected]m.au
Website: www.myeride.com.au
Address: 4 /54 Merrindale Drive Croydon South Victoria Australia 3136