Myson Kickspace 500E ECO Installation instructions

COMPLETE HEATING SOLUTIONS
KICKSPACE®500E ECO
& 600E ECO
INSTALLATION & OPERATING MANUAL
PLEASE LEAVE THIS MANUAL WITH THE END USER

1.0 Safety Information
For MYSON KICKSPACE®500E ECO & 600E
ECO, a fused electrical spur with a switch having
3mm separation on all poles must be provided in
an easily accessible position adjacent to the unit.
If the supply cord to the KICKSPACE®500E ECO
or 600E ECO is damaged, it must be replaced
by the manufacturer, its service agent or similar
qualified persons in order to avoid a hazard.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning the
use of the appliance in a safe way and understand
the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children unless they are older than 8
years and supervised.
Keep the appliance and its cord out of reach of
children aged less than 8 years.
Children of less than 3 years should be kept away
from the unit unless continuously supervised.
Children aged from 3 years and less than 8 years
shall only switch on / off the appliance provided
that it has been placed or installed in its normal
operating position and they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved.
Children aged from 3 years and less than 8 years
shall not plug in, clean the appliance or perform
user maintenance.
WARNING: KICKSPACE®500E ECO & 600E ECO models must be earthed.
WARNING: DO NOT cover the unit or obstruct the grille as this could give risk of fire.
1.0 Safety Information 02
2.0 Installation 03
3.0 Electrical Connection 03
4.0 Waste Disposal According to the
WEEE Directive (2012/19/EU) 03
5.0 Controls 04
6.0 Appendix 07
7.0 Eco Directive Characteristics 11
Contents
The KICKSPACE®500E ECO & 600E ECO models MUST NOT be installed in a bathroom
or other similar high humidity area.
02 KICKSPACE®500E ECO & 600E ECO
CAUTION: Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.

03
KICKSPACE®500E ECO & 600E ECO
1.02.03.04.0
2.0 Installation
l Before proceeding with the installation, the heating system
design must be considered and the unit correctly sized to
meet the heat loss requirements of the room.
l Before proceeding with the installation, unpack the carton
contents and check against the checklist below:
1. KICKSPACE®unit.
2. Instruction manual.
3. Warranty card.
4. Grille.
5. Screw fixing kit (with grille).
l This MYSON KICKSPACE®fan convector is designed for
installation in the cavity beneath kitchen cupboards in the
vacant floor space, or other similar locations.
l For KICKSPACE®500E ECO & 600E ECO a minimum of 25mm
clear headroom is required above the top of the KICKSPACE®
when fitted.
l The unit should be mounted on a clean and level floor area
under the cupboard base.
l KICKSPACE® 500E ECO & 600E ECO plinth mounting
(see Fig. 1) -
• The unit must be mounted on a suitable support.
• The support should be mounted on a clean and level floor
area under the cupboard base, and securely fitted.
• The top of the support must be level with the lower edge of
the cut-out when fitted.
l Decide the position of the KICKSPACE®, mark out and cut the
plinth to the dimensions using table on page 8.
l Position the KICKSPACE®under the cupboard in the required
location, with the front edge just behind the line of the plinth.
l Replace the plinth and bring the KICKSPACE®forward into
the opening so the front edge projects approximately 10mm
through the plinth.
l KICKSPACE®500E ECO & 600E ECO are fitted with a transit
cover to protect the electric element and to minimise risk
of electric shock prior to the grille being fitted. The cover
must only be removed with the electrical supply switched off
immediately prior to fitting of the grille.
l Align the grille and secure it to the unit with two screws
supplied (use the shorter screws). (See Fig. 2).
l Secure the unit/grille to the plinth with two screws supplied
(use the longer screws). (See Fig. 2).
l Complete the electrical installation, switch on and test the
KICKSPACE®(see Fig. 3).
l When installed in a kitchen consideration should be given to
storage of perishable goods in the cupboard above.
l No rear access to the unit shall be available after installation.
Waste disposal according to the WEEE Directive
(2012/19/EU). The symbol on the product label
indicates that the product may not be handled as
domestic waste, but must be sorted separately.
When it reaches the end of its useful life, it shall
be returned to a collection facility for electrical and electronic
products. By returning the product, you will help to prevent
possible negative effects on the environment and health to
which the product can contribute if it is disposed of as ordinary
domestic waste. For information about recycling and collection
facilities, you should contact your local authority/municipality or
refuse collection service or the business from which you purchased
the product. Applicable to countries where this Directive has
been adopted.
3.0 Electrical Connection
4.0 Waste Disposal According to the WEEE Directive (2012/19/EU)
l The electrical installation must comply with local or national
wiring regulations.
l This KICKSPACE®500E ECO is supplied fitted with a 2.0 metre
1.0mm2cord.
l This KICKSPACE®600E ECO is supplied fitted with a 2.0 metre
1.5mm2cord.
l For KICKSPACE®500E ECO & 600E ECO a fused electrical
spur with a switch having 3mm separation on all poles must be
provided in an easily accessible position adjacent to the unit.
l If the supply cord to KICKSPACE®500E ECO or 600E ECO is
damaged, it must be replaced by the manufacturer, its service
agent or similar qualified persons in order to avoid a hazard.
WARNING: KICKSPACE®500E ECO & 600E ECO models must be earthed.
Do not energise the electrical supply until the remaining stages of the installation have been completed.

04
5.0 Controls
KICKSPACE®500E ECO & 600E ECO
Function AdjustmentDescription
The display will show the ambient temperature.
Press OK, set temperature will begin to blink.
Use or to adjust the required room temperature.
Press OK to confirm.
The ambient room temperature will then display.
Default setting +21°C
Max temp setting +30°C
Min temp setting +5.5°C
Note: The thermostat has a LED indicator that will change colour
depending on the following:
≤21.0°C = Green
21.5°C - 24.0°C = Orange
≥24.5°C = Red
Note: To see the set temperature simply press .
See page 6 for ‘Programme Mode’ setup.
Note: When in AUTO mode it is possible to override by
selecting a new temperature. To do this while in AUTO mode,
press (OK), the temperature will begin to blink, change the
temperature using or and press (OK) to confirm.
The
temperature using
symbol will display showing the override and this will
last for 2 hours. To remove the override you can press .
Note: To see the set temperature simply press again.
Comfort Mode
Provides room temperature control for when
the room is occupied (see Fig. 3).
Heating mode – Electric
To enter this mode:
• Set the fan only/off/heating switch
to heating (red dot)
• Set the output switch to position I
• Select the fan speed switch to position I
The unit will now run on low speed.
To operate the 500E ECO at 2kW or the
600E ECO at 3kW:
• Set the output switch to position II
The unit will now run on high speed.
Automatic Setting
The unit will run according to one of the 9
preset timed programmes, or one of the 4 user
defined programmes.
Auto
This unit is controlled by the switches on the front of the unit
(see Fig. 3) and a wireless programmable thermostat.
The wireless programmable thermostat includes many features
and also ensures the electric KICKSPACE®products comply with
the Commision Regulation (EU) 2015/1188. These features
can be identified on the display of the wireless programmable
thermostat (see Fig. 4).
Locating the Wireless Programmable Thermostat
The wireless programmable thermostat includes a flip out stand
and can be freestanding in a suitable location. Alternatively it
can be wall mounted, fitting instructions can be seen in Fig. 5.
Wherever the wireless programmable thermostat is mounted/
used it should be out of direct sunlight, away from draughty
areas and clear of any potential heat sources. For optimum use
the thermostat should be fitted at a height of 1.5m from the
floor (see Fig. 6).
First use of the Wireless Programmable Thermostat
Remove the plastic insulator from the battery compartment in
the remote control. Hold OK for 10 seconds until ‘rF ini’ appears.
Press OK again and ‘ini’ flashes until the unit has paired with
the KICKSPACE®. The remote control reverts back to its normal
screen when paired.
Setting the date and time
Use and keys to choose from the following parameters.
A function is selected when the icon is surrounded by .
1. Select and press OK.
2. Press (OK) the hours will begin to blink.
3. Use or to change the hour and press (OK) to confirm,
the minutes will then begin to blink.
4. Use or to change the minutes and press (OK) to
confirm, the day number will then display.
5. Use or to change the day number, with Monday being
1 and press (OK) to confirm, the date and month will then
display and the day will begin to blink.
6. Use or to change the day and press (OK) to confirm,
the month will then begin to blink.
7. Use or to change the month and press (OK) to confirm,
the year will then display and begin to blink.
8. Use or to change the year and press (OK) to confirm,
and then scrolll or to go back to the main menu.
Operating Modes
Use and keys to choose from the following parameters. A function is selected when the icon is surrounded by .

05
KICKSPACE®500E ECO & 600E ECO
Operating Modes (continued...)
Function AdjustmentDescription
Holiday Function
Provides frost protection or overheat protection
during periods of absence (holiday).
Boost Function
Brings the unit on irrespective of the
programme or temperature setting for
a predefined period.
Default is 30 minutes.
Can be used in Comfort, Auto,
Night Set-Back mode.
Programme Menu
Provides choice from 9 pre-programmed and
4 user defined timed programmes.
The display will show the ambient temperature.
Press (OK), set temperature will begin to blink.
Use or to adjust the required room temperature.
Press (OK) to confirm.
The ambient room temperature will then display.
Default setting +19°C
Max temp setting +19°C - night set back temperature can not
be higher than comfort mode set point.
Min temp setting +5.5°C
Note: To see the set temperature simply press .
Night Set-back Setting
Provides room temperature controls for when
the room is not occupied.
5.0 Controls (continued...)
• For permanent frost protection select and press (OK).
is shown in permanent frost protection.
• For holiday frost protection press (OK) again, ‘no’ will blink.
Press button to increase number of hours (1-24)/days (1-99),
and press (OK) to confirm. Thermostat is now in holiday mode.
The will blink and will continue to blink until the
timer ends.
It is possible to exit the holiday function by pressing and
holding for 2 seconds.
Select using or or directly using button 20.
The time period in minutes will blink.
Use or to adjust time by increments of 10 minutes.
Press (OK) to confirm, the hourglass will begin to blink
and countdown.
It is possible to exit boost function by pressing .
Refer to following page.
5.0
P
Select using

06 KICKSPACE®500E ECO & 600E ECO
5.0 Controls (continued...)
Comfort Periods
P1 Morning, Evening & Weekend Weekday 07:00 - 09:00 & 17:00 - 23:00
Weekend 08:00 - 23:00
P2 Morning, Afternoon, Evening & Weekend Weekday 07:00 - 09:00, 12:00 - 14:00 & 17:00 - 23:00
Weekend 08:00 - 23:00
P3 Day & weekend Weekday 06:00 - 23:00
Weekend 08:00 - 00:00
P4 Evening & Weekend Weekday 15:00 - 23:00
Weekend 08:00 - 00:00
P5 Morning & Evening Weekday 06:00 - 08:00 & 21:00 - 23:00
Weekend 06:00 - 08:00 & 18:00 - 00:00
P6 Morning, Afternoon & Weekend Weekday 06:00 - 08:00 & 14:00 - 21:00
Weekend 07:00 - 21:00
P7 7h - 19h (Office) Weekday 07:00 - 19:00
Weekend n/a
P8 8h - 19h Saturday Weekday 08:00 - 19:00
Weekend 09:00 - 18:00 (Saturday only)
P9 Weekend only Weekday n/a
Weekend 08:00 - 00:00
Programme Mode
A quantity of 9 built-in (P1-P9) and 4 user defined (U1-U4) timed
programme options are available to choose from. Each day is
divided into 48 half hour periods operating in comfort mode.
Built-in Programme Selection
1. Select Pby pressing until ‘ProG’ is displayed.
2. Press (OK) twice and the programme number will begin
to blink.
3. Use or to select required programme (P1-P9).
4. Press (OK) to confirm the chosen programme.
User Programme Menu
1. Select Pby pressing until ‘ProG’ is displayed.
2. Press (OK) twice and the programme number will begin
to blink.
3. Use or to select a user defined programme (U1-U4).
4. Press and hold (OK) for 3 seconds to edit the programme.
5. The hour will now display, also note the segments on the
bottom of the display will begin to blink
- Press to set this half hour as night set back
- Press to set at comfort mode
- Note when pressing or you will automatically
move to the next half hour.
6. When you reach the final segment (23:30) press (OK) to move
to day 2 here you have the option to copy the same programme
that you have just created or create an alternative programme
a. To copy the programme press (OK) while YES is displayed
this can be copied to each day individually and it is
also possible to copy a number of days but then
change other days to an alternative programme by
selecting NO then pressing (OK)
b. To create an alternative programme for individual days
use or to change YES to NO then press (OK)
and repeat from step 6.
7. After completing the last day the word SAVE will appear,
press (OK) to save changes.
The thermostat will then automatically enter AUTO mode to
follow the selected programme.

07
KICKSPACE®500E ECO & 600E ECO
5.0 Controls (continued...)
6.0 Appendix
5.0
500E ECO
600E ECO
Low (l)
Boost (ll)
Low (l)
Boost (ll)
1000
2000
1500
3000
Heat Output (Watts)
Heating Performance Data
Output switch
Sound Levels
Model Sound Pressures at 2.5m (dBA)
500E ECO 25.7 38.1
600E ECO 26.4 37.2
Normal Boost
Weight and Rated Power
ModelModel Rated Power (W) Unit Weight (kg)
500E ECO 2025 3.1
600E ECO 3040 3.6
Sound levels tested in accordance with EN 23741.
6.0
Installer’s Set-up Parameters
To access the installation parameters menu, press and hold (OK)
for 10 seconds. Use or to highlight the parameter to be
adjusted then press (OK) to toggle the parameter setting, when
the value starts to blink, use or to adjust the value. Then
press (OK) to confirm. Once parameters are set, go to <End>
parameter and press (OK) to go back to the main menu.
Parameter
Name Default SettingDescription Alternative Setting
Manually pair the thermostat to the receiverrF ini Press (OK) to begin pairing
Myson Smart Start (Adaptive Start) Thermostat will learn
to achieve temperature by time requested
At NoYes
Window open detection, product will switch off if a large
temperature drop is detected (usually caused by an open
window / door)
oP NoYes
Room temperature limiter (limits the maximum room
temperature set point)
Lt 20°C< TR MAX <30°C30°C
Press OK
Automatic daylight saving time adjustment No - manualYes - automatic
n/an/a
Ch
Reverts the control back to factory settingsCL
Version numberUE
Exit the installation menuEnd
Fan Only Mode
If required, the unit can be used in summer for air circulation
without heat.
• Set the fan only/off/heating switch to fan only (blue dot)
• Adjust fan speed to required setting
Note: This mode will by-pass the wireless programmable
thermostat and also breaks the pairing link therefore when
switching back to heating mode it may take up to 5 minutes for
the thermostat to automatically pair with the receiver.
Press and hold OK for 10 seconds to reset

08 KICKSPACE®500E ECO & 600E ECO
KICKSPACE®500E ECO KICKSPACE®600E ECO
A
Fig. 1 Plinth opening - plinth mounting
B
Dimensions (mm) Dimensions (mm)
N.B: Add 4.5mm to the chassis height to allow for rubber mountings and screws.
6.0 Appendix (continued...)
Fig. 2 Front view of unit
Unit Securing Screws
Grille Securing Screws
Fig. 3
Dimensions
A B
Dimensions (mm)
466
520
93
93
500E ECO
600E ECO
A = Width of cut out B = Height of cut out
Model
321
Mains cable entry
Top view
496
101
FRONT GRILLE
Mains cable entry
View on arrow
93
46
203
177 203
177
Top view
View on arrow
93
46
375
Mains cable entry
Mains cable entry
101
FRONT GRILLE
550
Heating System
Switch
Fan only / Off / Heating
Blue dot (B) / O / Red dot (R)
Boost / Low
II / I
Boost / Normal
II / I
Heating Selector
Switch
Fan Only Speed
Switch
(B) (OFF) (R)

09
KICKSPACE®500E ECO & 600E ECO
6.0 Appendix (continued...)
6.0
1. Weekly programme and OFF symbol
2. Radio transmission indicator
3. Keypad lock activated
4. Exemption programme
5. Programme schedule and time indicator
6. Programme number
7. Current day
8. Low battery indicator
9. If ON => Room temp, displayed
10. Set temperature or room temp / Hour and
date during adjustment/time of boost period
11. Behaviour indicator (3 led colours - green,
orange and red), visible through the plastic
12. Open window detection
13. Appears when in user setting menu
14. Comfort mode
15. Auto mode
16. Reduced mode
17. Holiday mode
18. Boost mode
19. Return button
20. Boost button
21. Minus button
22. Plus button
23. Validation button
Fig. 4 KICKSPACE® thermostat controls
14
7
6
12
8
2
5
4 3 13
19 20
2221 23
19
9
10
115 16 17

10 KICKSPACE®500E ECO & 600E ECO
6.0 Appendix (continued...)
Fig. 5 Fitting instructions
1
3
2
OK
Fig. 6

11
KICKSPACE®500E ECO & 600E ECO
7.0 Eco Directive Characteristics
Item Symbol Value Unit
Heat Output
Nominal heat output
KICKSPACE®500E ECO Pnom 2.03 kW
Nominal heat output
KICKSPACE®600E ECO Pnom 3.04 kW
Minimum heat output (indicative)
KICKSPACE®500E ECO Pmin N.A. kW
Minimum heat output (indicative)
KICKSPACE®600E ECO Pmin N.A. kW
Maximum continuous heat output
KICKSPACE®500E ECO Pmax,c 2.03 kW
Maximum continuous heat output
KICKSPACE®600E ECO Pmax,c 3.04 kW
Auxiliary electricity consumption
At nominal heat output eImax 0.00 kW
At minimum heat output eImin N.A. kW
In standby mode eISB N.A. kW
Model identifier(s): KICKSPACE®500E ECO
KICKSPACE®600E ECO
Item Unit
Type of heat input, for electric storage local space heaters only
manual heat charge control, with integrated thermostat N.A.
manual heat charge control with room and/or outdoor
temperature feedback N.A.
electronic heat charge control with room and/or outdoor
temperature feedback N.A.
fan assisted heat output N.A.
Type of heat output/room temperature control
single stage heat output and no room temperature control no
two or more manual stages, no room temperature control no
with mechanic thermostat room temperature control no
with electronic room temperature control no
electronic room temperature control plus day timer no
electronic room temperature control plus week timer yes
Other control options
room temperature control, with presence detection no
room temperature control, with open window detection yes
with distance control option no
with adaptive start control yes
with working time limitation no
with black bulb sensor no
Contact details Rettig UK Ltd, Eastern Avenue, Team Valley, Gateshead, Tyne & Wear, NE11 0PG, United Kingdom
7.0 6.0

Product code and
serial number location
Product Serial Number:
COMPLETE HEATING SOLUTIONS
01.12.18