N&W Global Vending Canto Plus Instant Owner's manual

INSTALLATION, OPERATION, MAINTENANCE
EN English
Do c . No. H 3375EN 01
Ed i t i o n 2 07 - 2010
Canto Plus
Instant

Italiano ¿º¿¹¾¿·È·¹¾»·÷¹¹¾¿Ä·Ƒº»É¹È¿ÊÊ·Ļ·ʷȽ¾»ÊÊ·º¿¿º»ÄÊ¿Ű¹·Ð¿ÅÄ»Ƒò
¹ÅļÅÈû·Â»º¿ÉÆÅɿпÅÄ¿»½¿É·ʿ̻º»Â»¿È»ÊÊ¿Ì»ËÈÅÆ»»»Â»Ä¹·Ê»··ÊÅ»É˹-
¹»ÉÉ¿Ì»Ãź¿Ű¹¾»»º¿ÄÊ»½È·Ð¿ÅÄ¿Ɣ
English ¾»÷¹¾¿Ä»º»É¹È¿¸»º¿Äʾ»¿º»ÄÊ¿Ű¹·Ê¿ÅÄÆ·ʻ¹ÅļÅÈÃÉÊÅʾ»»½¿É·-
Ê¿Ì»º¿È»¹Ê¿ÅÄÉżʾ»ËÈÅÆ»·Äº¿È»¹Ê¿Ì»É¿ÉÊ»º·ÊÉ¿º»·Äº¼ËÈʾ»È·Ã»ÄºÃ»ÄÊÉ·Äº
¿ÄÊ»½È·Ê¿ÅÄÉ
English ¾»¾·ÈÃÅÄ¿É»ºÉʷĺ·ÈºÉÅÈÊ»¹¾Ä¿¹·ÂÉÆ»¹¿Ű¹·Ê¿ÅÄÉƺº»É¿½Ä·Ê¿ÅÄÉƻ;¿¹¾
¹ÅÃÆÂÏͿʾ½Åź»Ä½¿Ä»»È¿Ä½ÆÈ·¹Ê¿¹»¿ÄÉ·¼»ÊÏ÷ÊÊ»ÈÉ¿Ä¼Åȹ»Ϳʾ¿Äʾ»¾·Ì»
¸»»Ä·ÆÆ¿»º·È»Ɠ
Français ·÷¹¾¿Ä»ºó¹È¿Ê»ÉËÈ·Æ·ÇË»ÊÊ»ºƠ¿º»ÄÊ¿Ű¹·Ê¿ÅÄ»ÉÊ¹ÅļÅÈû·ËÎ
º¿ÉÆÅÉ¿Ê¿ÅÄÉÂó½·Â»Éº»Éº¿È»¹Ê¿Ì»É»ËÈÅÆó»ÄÄ»ÉóÄÅĹó»É¹¿Ɩ¹ÅÄÊÈ»»ÊÃź¿Ű¹·Ê¿ÅÄÉ
»Ê¿ÄÊó½È·Ê¿ÅÄÉÉ˹¹»ÉÉ¿Ì»É
Español »º»¹Â·È·ÇË»·ÃÒÇË¿Ä·Ƒº»É¹È¿ÆÊ·»Ä·»Ê¿Ç˻ʷº»¿º»ÄÊ¿Ű¹·¹¿ĤÄƑ¹ËÃ-
Æ»¹ÅÄ·Éº¿ÉÆÅÉ¿¹¿ÅÄ»É»½¿É·ʿ̷Éº»·É¿È»¹ÊÈ¿¹»ÉËÈÅÆ»·É¿ÉÊ·º·É·Â÷Ƚ»Ä
Ïº»ÉËÉÉ˹»É¿Ì·ÉÃź¿Ű¹·¹¿ÅÄ»É»¿ÄÊ»½È·¹¿ÅÄ»É
Português »¹Â·È·ƖÉ»ÇË»·ÃÒÇË¿Ä·Ƒº»É¹È¿Ê·Ä·Æ·¹·º»¿º»ÄÊ¿Ű¹·îÙÅ»ÉÊÒ¹ÅÄ-
¼ÅÈû·Éº¿ÉÆÅÉ¿îī»É»½¿É·ʿ̷Éº·É¿È»ÊȿлÉËÈÅÆó¿·É»Â»Ä¹·º·É·ÇË¿·Å·ºÅ»
É˹»ÉÉ¿Ì·ÉÃź¿Ű¹·îī»É»¿ÄÊ»½È·îī»É
Deutsch ·É·Ë¼º»ÃÏÆ»Äɹ¾¿Âº¸»É¹¾È¿»¸»Ä»»ÈÚÊ»ÄÊÉÆÈ¿¹¾Êº»ÄÈ»¹¾ÊÉ·Ë¼½»-
¼Ŏ¾ÈÊ»Ä½»É»Êп¹¾»ÄËÈÅÆڿɹ¾»Ä¿¹¾Ê¿Ŀ»ÄƑÉÅÍ¿»·Äɹ¾Â¿»Ņ»Äº»Ä'ĺ»ÈËĽ»Ä
ËĺȽÚÄÐËĽ»Ä
Nederlands »÷¹¾¿Ä»¸»É¹¾È»Ì»ÄÅÆ¾»Ê¿º»ÄÊ¿Ű¹·Ê¿»Æ··ÊÀ»¿É¹ÅļÅÈÃº»
Í»Êɸ»Æ·Â¿Ä½»ÄÌ·Äº»ËÈÅƻɻ¿¹¾Ê¿ÀÄ»Äº¿»¾¿»ÈÄ··ÉÊÌ»ÈûºÍÅȺ»Ä»Ä·ʻȻ
·Ã»Äº»Ã»ÄÊ»Ä»Ä··ÄÌË¿Ľ»Ä
Italiano »ÄÅÈû·ÈÃÅÄ¿ÐзʻÅ»ÉÆ»¹¿Ű¹¾»Ê»¹Ä¿¹¾»ƺº»É¿½Ä·Ð¿ÅÄ¿ƻ¹¾»ÉÅÄÅ
ÉÊ·Ê»·ÆÆ¿¹·Ê»¿Ä·¹¹ÅȺÅ¹ÅÄ»È»½Å»º»Â·¸ËÅÄ··ÈÊ»¿Ä÷ʻȿ·º¿É¿¹ËÈ»Ðз¿Ä
Ì¿½ÅÈ»Ļ·ÉÅÄÅƓ
Français »ÉÄÅÈûÉ¾·ÈÃÅÄ¿Éó»ÉÅË»ÉÉÆó¹¿Ű¹·Ê¿ÅÄÉÊ»¹¾Ä¿ÇË»ÉƺºóÉ¿½Ä·Ê¿ÅÄÉƻ
ÇË¿ÅÄÊóÊó·ÆÆ¿ÇËó»É¹ÅļÅÈÃóûÄÊ·ËÎÈò½Â»Éº»·¸ÅÄÄ»ÆÈ·Ê¿ÇË»»Ä÷ʿòÈ»º»
Éó¹ËÈ¿Êó»ÄÌ¿½Ë»ËÈº·ÄÉÂƠÉÅÄÊƓ
Deutsch ¿»¾·ÈÃÅÄ¿É¿»ÈÊ»Äʷĺ·ÈºÉź»ÈÊ»¹¾Ä¿É¹¾»ÄƻпŰÁ·Ê¿ÅÄ»Äƺ»ÉÊ¿Ã-
ÃËĽ»ÄƻƑº¿»º»Ä»½»ÂÄº»ÈËÄÉÊ¾¿ÄÉ¿¹¾Ê¿¹¾º»Ä¿Äº»È½»Âʻĺ»Ä¿¹¾»È¾»¿ÊÉ-
ÄÅÈûÄ»ÄÊÉÆÈ»¹¾»ÄƑɿĺƓ
Español ·ÉÄÅÈ÷É·ÈÃÅĿзº·ÉÅ·É»ÉÆ»¹¿Ű¹·¹¿ÅÄ»ÉÊó¹Ä¿¹·Éƺº»É¿½Ä·¹¿ÅÄ»Éƻ
ÇË»¾·ÄÉ¿ºÅ·Æ¿¹·º·Éº»·¹Ë»ÈºÅ¹ÅÄ·ÉÈ»½Â·Éº»·¸Ë»Ä·ÆÈҹʿ¹·»Ä÷ʻȿ·º»
É»½ËÈ¿º·ºÌ¿½»ÄÊ»É»Ä·ÉÅÄƓ
PortuguêsÉÄÅÈ÷É¾·ÈÃÅĿзº·ÉÅË·É»ÉÆ»¹¿Ű¹·îī»ÉÊó¹Ä¿¹·Éƺº»É¿½Ä·îī»Éƻ
ÇË»¼ÅÈ·Ã·Æ¿¹·º·Éº»·¹ÅȺÅ¹ÅÃ¸Å·ÉÈ»½È·Éº»»Ä½»Ä¾·È¿·»Ã÷ÊóÈ¿·º»É»½-
ËÈ·Äî·»ÃÌ¿½ÅÈÄ·ÉÙÅƓ
Nederlands »½»¾·ÈÃÅÄ¿É»»Èº»ÄÅÈûÄżÊ»¹¾Ä¿É¹¾»ÉÆ»¹¿Ű¹·Ê¿»Éƺ··ÄÍ¿ÀпĽ»Äƻ
º¿»ÊÅ»½»Æ·ÉÊͻȺ»ÄÌŽ»ÄÉº»¿Äº»Ì·ÄÁÈ·¹¾ÊпÀĺ»»¿É»ÄÌ·Ä½Å»ºÌ·Á÷Ä-
ɹ¾·Æ¿ÄзÁ»Ì»¿Â¿½¾»¿ºпÀÄº»ÌŽ»Äº»Ɠ
܎܎Ơ܎
܎܎
@܎܎@
''
o܎܎
;&܎܎܎
܎܎܎
·È½¾»ÊÊ·º¿¿º»ÄÊ¿Ű¹·Ð¿ÅÄ»
º»ÄÊ¿Ű¹·Ê¿ÅÄ·¸»Â
·Â¸È»Ã¸ÅƑʷʸƭʷʸƭʹʷʸʷ
ANTONIO CAVO
ƔƔ
Direttive europee
European directives
ÅÉÊ¿ÊË¿Ê·º·
»Æ»·Â»º¸Ï
ʹʷʷʽƭʻʹƭ
ʾʺƭʹʺƭˀʺƭʽʿƭ ʹʷʷʽƭˀʼƭ
ʿˀƭʺʺʽƭˀʹƭʺʸƭ
ˀʺƭʽʿƭ
ʹʷʷʻƭʸʷʿƭ
ˀʷƭʸʹʿƭ ʹʷʷʹƭʾʹƭ
ʿʷƭʼˀʷƭ·Äºʿˀƭʸʷˀƭ

ʸˀʺʼƭʹʷʷʻ
ÅÈû·ÈÃÅÄ¿Ðзʻƭ
Æ»¹¿Ű¹¾»Ê»¹Ä¿¹¾»
Harmonised standards
»¹¾Ä¿¹·ÂÉÆ»¹¿Ű¹·-
tions
ʽʷʺʺʼƖʸƓʹʷʷʹʸʸƓʹʷʷʷʼʸƓʹʷʷʼ
ʸʹƓʹʷʷʽʹƓʹʷʷʽ
ʽʷʺʺʼƖʹƖʾʼƓʹʷʷʻʸƓʹʷʷʼʸʸƓʹʷʷʽ
ʼʷʺʽʽƓʹʷʷʺʸƓʹʷʷʽ
ʸʸʹʷʸ·Äºʺʾʻʻ
ʼʼʷʸʻƖʸʸʹ
ʼʼʷʹʹʸʹ
ʼʼʷʸʻƖʹʸ
ʽʸʷʷʷƖʺƖʹ
ʽʸʷʷʷƖʺƖʺʸ
ʽʸʷʷʷƖʻƖʹʸʹ
ʽʸʷʷʷƖʻƖʺʸʹ
ʽʸʷʷʷƖʻƖʻʸ
ʽʸʷʷʷƖʻƖʼʸ
ʽʸʷʷʷƖʻƖʽʸ
ʽʸʷʷʷƖʻƖʸʸʸ
Â¼·É¹¿¹ÅÂÅÊ»¹Ä¿¹Åò¹ÅÉÊ¿ÊË¿ÊÅÆÈ»ÉÉÅƓ
¾»Ê»¹¾Ä¿¹·ÂŰ»¿É¹ÅÃƿ»º·ÊƓ
ųƔÆƔƔ

Declaration of conformity
The declaration of conformity with the European Direc-he declaration of conformity with the European Direc-
tives and Standards provided for by the laws in force
is supplied by the rst page of this manual, which is an
integral part of the machine.
It is declared that the machine described by
the identication plate is in compliance with the
provisions of the European Directives, its sub-
sequent amendments and integrations as well as with
the harmonised standards or technical specications
(designations) applied in compliance with the safety
rules of good practice enforced in the EU and listed on
the same page.
Warnings
f o r i n s t a l l a t i o n
The installation and any subsequent maintenance
operation shall be carried out by the personnel
skilled and trained on the utilisation of the machine
according to the rules in force.
The machine is sold without any payment system. As
a consequence, only the installer will be liable for any
damage that may be caused to the machine or to things
and persons by an incorrect installation of the payment
system.
The intactness of the machine and its compliance
with the standards of relevant installations must be
checked by skilled personnel at least once a year.
Package materials must be disposed of in observance of
the environment.
f o r u s e
The machine can be used by children and by people
having reduced physical, sensorial or mental skills under
the supervision of people responsible for their safety or
specically trained on the use of the machine. Children
shall be prevented from playing with the machine by the
people in charge of their supervision.
f o r t h e e n v i r o n m e n t
Some tricks will help you to protect the environment:
- use biodegradable products to clean the machine;
- properly dispose of all the packages of the products
used to fill and clean the machine;
- power off the machine during inactivity for energy sav-
ing.
f o r s c r a p p i n g
The symbol shows that the machine can not
be disposed of as common waste, but it must
be disposed of as it is established by the
2002/96/CE (Waste Electrical and Electronics
Equipments - WEEE) European Directive and
by the national laws arising out of it in order to prevent
any negative consequence for environment and human
health.
The dierentiated collection of the machine at the end of
its life is organised and managed by the manufacturer.
For the correct disposal of the machine contact the sales
point where you have purchased the machine or our
after-sales service.
The unlawful disposal of the machine implies the appli-
cation of the administrative sanctions provided for by the
rules in force.
Attention!
If the machine is equipped with a cooling system, the
cooling unit contains HFC-R134a uoridised greenhouse
eect gas ruled by the Kyoto protocol, the total heating
potential of which is equal to 1300.

© by N&W GLOBAL VENDING S.p.A. 107 - 2010 3375 - 01
English
TABLE OF CONTENTS
PAGE PAGE
dE c l a r a t i o n o f c o n f o r m i t y
Wa r n i n g s
INTRODUCTION 2
id E n t i f i c a t i o n o f t h E m a c h i n E 2
inc a s E o f f a i l u r E 2
tr a n s p o r t a n d s t o r a g E 2
po s i t i o n i n g o f t h E v E n d i n g m a c h i n E 3
TE c H N i c a l f E a T u r E s 3
va r i a b l E c o m b i n a t i o n l o c k 6
FILLING AND CLEANING 7
do o r s W i t c h 7
hy g i E n E a n d c l E a n i n g 7
us i n g t h E d i s p E n s E r s 7
co N T r o l s a N D i N f o r m a T i o N 8
lo a D i N g 8
cl E a n i n g 9
INSTALLATION 11
do o r s W i t c h E s 11
un p a c k i n g t h E v E n d i n g m a c h i n E 11
pl a t E in s E r t i o n 12
Wa t E r s y s t E m c o n n E c t i o n 13
El E c t r i c a l c o n n E c t i o n 14
fi l l i n g t h E W a t E r c i r c u i t 15
op E r a T i o N 16
in s t a n t d i s p E n s i n g c y c l E 17
PROGRAMMING 19
po W E r o n 19
no r m a l o p E r a t i o n m o d E 20
Na v i g a T i o N 20
di s p l a y 20
kE y b o a r d 21
fi l l E r mE N u 21
st a t i s t i c s 21
in d i v i d u a l p r i c E 22
ma n a g E m E n t o f c h a n g E t u b E s 22
tE m p E r a t u r E d i s p l a y 22
tE s t d i s p E n s i n g 22
gsm p r E a l a r m s 22
Evadts t r a n s f E r 22
TE c H N i c i a N mE N u 23
pa y m E n t sy s t E m s 23
pr i c E s 27
do s E s 27
ma c h i n E co n f i g u r a t i o n 30
tE s t 34
co m m u n i c a t i o n 38
fa i l u r E s 39
MAINTENANCE 42
gE n E r a l in t r o d u c t i o n 42
pE r i o D i c a l op E r a T i o N s 42
ch a n n E l s a n d m i x E r s 43
cu p d i s p E n s E r 44
pr o d u c t c o n t a i n E r s 45
bo i l E r ma i n t E n a n c E 45
Bo a r D f u N c T i o N 47
El E c t r o n i c b o a r d co n f i g u r a t i o n 47
c. p. u. b o a r d 48
ac t u a t i o n b o a r d 49
in s t a n t b o i l E r c o n t r o l r E l a y 50
cu r r E n t r E g u l a t o r b o a r d 50
Wa t E r ci r c u i t 51
pr o g r a m m i N g s u m m a r y 52
Wi r i N g D i a g r a m 53

© by N&W GLOBAL VENDING S.p.A. 207 - 2010 3375 - 01
Introduction
The technical documentation supplied is an integral
part of the equipment and it must therefore accom-
pany the equipment whenever it is either moved
or transferred to enable the various operators to
consult it.
Before starting to install and use the machine, it is nec-
essary to carefully read and understand the content of
the documentation since it can supply important informa-
tion on installation safety, utilisation rules and mainte-
nance operations.
The manual is divided into three chapters.
The chapter is intended to describe the ordinary
lling and cleaning operations that shall be carried out
in areas of the machine that can be accessed with the
simple use of the door key, without using any other tool.
The second chapter contains the instructions for correct
installation as well as the information necessary for opti-
mal utilisation of the machine performance.
The third chapter is intended to describe the mainte-
nance operations involving the use of tools for access to
potentially dangerous areas.
The operations described in the second and third
chapter must be carried out only by the person-

operation from the point of view of electric safety
and health rules.
IDENTIFICATION OF THE MACHINE AND
ITS FEATURES
Every single machine is identied by a specic serial
number that can be found on the rating plate arranged
inside on the right side.
The plate (see gure) is the only one recognised by the
manufacturer and it contains all the data that enable the
manufacturer to supply technical information of any kind
in a quick and safe manner and to facilitate the manage-
ment of spare parts.
IN CASE OF FAILURE
In most cases, any technical problem can be solved by
carrying out minor operations. As a consequence, we
suggest carefully reading this manual before contacting
the manufacturer.
In case of failures or malfunctions that can not be solved,
please apply to:
N&W GLOBAL VENDING SpA
Via Roma 24
24030 Valbrembo
Italy - Tel. [phone]
TRANSPORT AND STORAGE
To avoid damaging the machine, loading and unload-
ing operations shall be performed with great care. It is
possible to lift the machine by means of a motor-driven
or manual lift truck by positioning the forks beneath the
machine and on the side clearly stated by the symbol on
the cardboard package.
Please avoid:
- Overturning the vending machine;
- Dragging the vending machine by means of ropes or
alike;
- Lifting the vending machine by its sides;
- Lifting the vending machine by means of slings or
ropes
- Shaking the vending machine and/or the package
For storage it is necessary to keep the room dry at a
temperature between 0 and 40 °C.
Never stack several machines and never forget to keep
the vertical position specied by the arrows on the pack-
age.
Boiler data
Absorbed power
Operating voltage
Model
Product code
Water system features
Current
Frequency
Serial no.
Type
Fig. 1

© by N&W GLOBAL VENDING S.p.A. 307 - 2010 3375 - 01
POSITIONING THE VENDING MACHINE
The machine is not suitable for installation outdoors. It
must be installed in a dry room at a temperature ranging
from 2°C to 32°C. It can not be installed in a room where
water jets are used for cleaning (e.g. large kitchens, etc.).
The machine must be installed near a wall, but in such a
way that the back is min. 4 cm. far from the wall in order
to provide for regular ventilation. It shall never be cov-
ered with pieces of cloth or alike.
The machine shall be arranged to prevent maximum
inclination from exceeding 2°.
If necessary, level it by using the adjustable feet (see g.
13) supplied with the machine.
TECHNICAL FEATURES
Height mm. 1830
Width mm. 650
Depth mm. 760
Overall dim. with open door mm. 1320
Weight Kg 170
Power supply voltage V~ 230
Power supply frequency Hz 50
Installed power W 2250
cu p D i s p E N s E r
The diameter of the upper edge is 73-74 mm. or 70-71
mm. according to the markets of destination, self-con-
tained for about 650 cups.
pa y m E N T s y s T E m
The machine is electrically pre-arranged for systems
with an Executive, MDB or BDV protocol and for the as-
sembly of 24 Vdc validators.
The space is not only arranged to accommodate the
coin mechanism, but also to assemble the most wide-
spread payment systems (optionals).
sa l E s p r i c E s
You can set up a programmable dierent price for every
single selection. A sales price that is the same for all
selections is available for the standard setup.
Ex T E r N a l l i g H T i N g
By means of class-1 LEDs.
LEDs are generally protected by transparent panels. If
you remove panels for any reason, the light of the LEDs
may be dangerous if you directly look at it.
EN E r g y s a v i N g
You can set up the power o of LEDs and/or boilers on
2 daily time bands that can be programmed on a weekly
basis to save electric energy during non-use periods.
Ju g fa c i l i T i E s a N D f r E E v E N D (o p T i o N a l )
Use a special key to get up to 9 selections without
dispensing a cup to ll in a jug or to get a free delivery of
normal selections.
Fig. 2

© by N&W GLOBAL VENDING S.p.A. 407 - 2010 3375 - 01
co i N B o x
Made of galvanised sheet iron. Cover and lock available
as accessories.
Wa T E r s u p p l y
Supplied by the network, the water pressure of which lies
between 0.05 and 0.85 MPa (0.5 and 8.5 bar)
The machine software can manage the water supply
from an internal tank (optional kit).
po s s i B l E a D J u s T m E N T s
Coee, instant and water doses: time-based.
Temperature: Adjustable via software.
co N T r o l s
Cup presence-
Water presence-
Liquid waste empty-
Operation temperature reached-
Cup shift position-
sa f E T y D E v i c E s
Door switch-
Boiler safety thermostat manually reset-
Air-break float jam-
Anti-flood solenoid valve-
Float controlling liquid waste-
Boiler probe shortcircuit / interruption control-
Heat protection for:-
Pumps
Ingredient motors
Whipper motors
Protection with fuse-
Main electric circuit
Board and coin mechanism supply transformer
(Primary and secondary)

© by N&W GLOBAL VENDING S.p.A. 507 - 2010 3375 - 01
co N T a i N E r c a p a c i T y
Containers having a 2.5, 4.5 or 6 l capacity can be
mounted for instant products, according to models.
The indicative product quantity is summed up by the fol-
lowing table:
Container size 2.5 l 4.5 l 6 l
 0.6 1.0 1.3
 0.6 1.0 1.3
 1.7 3.2 4.5
 2.0 3.5 5.0
 2.0 3.5 5.0
 1.4 2.5 3.5
 0.6 1.0 1.3
The actual quantity can deviate from the above, accord-
ing to the specic weight of the various products.
The stacker, if any, contains about 1000 stirrers
El E c T r i c E N E r g y c o N s u m p T i o N
The electric energy consumption of the machine will
depend upon many factors such as the temperature and
ventilation of the room where the machine is installed,
the inlet water temperature, the boiler temperature, etc.
The following energy consumption values have been
measured at a room temperature of 22°C:
Temperature reached W/h 398
For 24h stand-by W/h 2,754
The energy consumption calculated on the average val-
ues above shall be understood as merely indicative.
ACCESSORIES
A wide range of accessories can be mounted on the
machine to vary its performances:
The assembly kits are supplied with mounting and test-
ing instructions that shall be strictly followed to preserve
the machine safety.
Assembly and any subsequent testing operation

-
tion from the point of view of electric safety and
health rules.
Fig. 3
Right outlet port1-
Left outlet port2-
Mixer3-
Central outlet port4-
6 l container5-
2.5 l container6-
4.5 l container7-

© by N&W GLOBAL VENDING S.p.A. 607 - 2010 3375 - 01

Some models are supplied with a variable combination
lock.
The lock is complete with a silver key for normal opening
and closing operations.
It is possible to customise the locks by using a kit made
available as an accessory and intended to change the
lock combination.
The kit is composed by a change key (black) of the cur-
rent combination as well as by change (gold) and use
(silver) keys of the new combination.
Sets of change and use keys with other combinations
can be supplied upon request.
Moreover, further sets of use keys (silver) may be re-
quested by specifying the combination stamped on the
keys.
Generally, only the use key (silver) shall be used where-
as the combination change keys (gold) can be kept as
spare keys.
-

To change the combination:
- Open the machine door to avoid forcing the rotation;
- Slightly lubricate by using a spray inside the lock;
- Insert the current change key (black) and turn it until
you reach the change position (reference notch at
120°);
- Remove the current change key and insert the change
key (gold);
- Turn it until you reach the close position (0°) and re-
move the change key.
The lock has now assumed the new combination.

used for the new combination.
Fig. 4

© by N&W GLOBAL VENDING S.p.A. 707 - 2010 3375 - 01
Chapter 1
Filling and cleaning
The machine is not suitable for installation outdoors. It
must be installed in a dry room at a temperature ranging
from 2°C to 32°C. It can not be installed in a room where
water jets are used for cleaning (e.g. large kitchens, etc.).
DOOR SWITCH
Whenever you open the door, a special switch will power
o the electric installation of the equipment to allow the
user to carry out the ordinary lling and cleaning opera-
tions described here below in totally safe conditions.
All the operations requiring the machine to be
directly connected to a source of electricity when
the door is open must be ONLY carried out by the


HYGIENE AND CLEANING
The operator of an automatic vending machine is re-
sponsible for the hygiene of the materials in contact with
foodstus on the basis of the health and safety rules in
force. As a consequence, it shall maintain the machine
so as to prevent the build-up of bacteria.
At the time of the installation, it is necessary to
completely sanitise the water circuits and the parts

bacterium that may have built up during storage.
It is recommended to use sanitising products also in
order to clean the surfaces not directly in contact with
foodstus.
Some parts of the machine can be damaged by corro-
sive detergents.
The manufacturer will disclaim all responsibility for any
damage caused by the non-observance of the above or
by the utilisation of corrosive or toxic chemical agents.
-
ing out any maintenance operation that may require
the disassembly of components.

IN OPEN CONTAINERS
(E.g. Plastic cups, pottery cups, jugs)
The dispensers of drinks in open containers may be only
used for selling and dispensing drinks obtained by:
brewing of products such as coffee and tea;-
reconstituting soluble or freeze-dry packed products;-
These products shall be declared as “suitable for auto-
matic dispensing” in open containers by the manufac-
turer.
Dispensed products shall be consumed immediate-
ly. Under no circumstance shall they be preserved

Any other use shall be considered as improper and
therefore potentially dangerous.
Fig. 5
Liquid waste bucket1-
Door switch2-
Dispensing compartment3-
Cup dispenser4-
Sugar container (optional)5-
Cup stacker6-
Permanently live socket7-
Mains fuse8-
Instant powder containers9-
Mechanical counter (optional)10-
Door open signalling micro (optional)11-
Service buttons12-
Mixer13-
Dispensing nozzles14-
Compartment closing flap15-

© by N&W GLOBAL VENDING S.p.A. 807 - 2010 3375 - 01
CONTROLS AND INFORMATION
The machine shall work at a room temperature between
2 and 32 °C.
The controls and information for the user are arranged
outside the door (see g. 6).
The labels including the menu and the instructions are
supplied with the machine and they shall be inserted at
the time of the installation.
The programming button giving access to the functions
of the machine, the mixer washing button and the con-
nector for the RS232 serial port are arranged inside the
machine, on the cover of the coin mechanism compart-
ment.
No i s E l E v E l
The continuous, equivalent, weighted sound pressure
level is below 70 dB.
LOADING
cu p s
The cup dispenser shelf has got a double articulated
joint intended to improve the accessibility to the cup dis-
penser, in particular when the machine is bank-installed.
To load the column, act as follows:
Open the machine door.-
Pull the shelf to release the dispensing compartment.-
Turn the shelf to the outside-
Remove the cover from the cup stacker;-
Load the cups.-
sT a c k E r c o m p l E T E l y E m p T y-
Fill in the columns with cups,- excluding the one rela-
tive to the dispensing hole;
Close the machine door and wait for the first full column-
to reach the dispensing hole;
Open the machine door once again and load the col--
umn that has remained empty;


is slightly required to close completely.
Fig. 6
Dispensing compartment1-
Lock2-
Space for payment systems3-
Graphical display4-
Free vend / Jug key (optional)5-
Coin insert LEDs6-
Coin insert / return7-
Coin return button8-
Preselection buttons9-
Numeric pushbutton panel (alternative)10-
Information spaces for the user11-
Menu labels12-
Direct selection keyboard (alternative)13-
Coin return flap14-
Fig. 7
Shelf extraction knob1-
Articulated shelf2-
Cover3-
Cup stacker4-
Sugar container (optional)5-
Cup release button6-

© by N&W GLOBAL VENDING S.p.A. 907 - 2010 3375 - 01
su g a r
The sugar container can be located on the cup shelf
(see g. 8) or with the other powder containers, accord-
ing to models.
The sugar conveyor and slide shall be cleaned at regular
intervals.
iN s T a N T p r o D u c T s
A self-adhesive label intended to specify the product is
arranged on every single container.
After having lifted the cover, pour the products that shall
be dispensed into every single container. Avoid com-
pressing and packing them. Make sure that the products
are not lumpy.
CLEANING
co l o u r c o D E
To make cleaning operations easier, the parts to be
cleaned and sanitised at regular intervals can be identi-
ed by their blue colour.
Act on the green parts to disassemble the blue parts.
Provide for cleaning and sanitising.
Only some parts relative to Espresso and Fresh Brew
units fail to follow this rule since made of a specic mate-
rial.
sa N i T i s i N g m i x E r s a N D f o o D c i r c u i T s
The mixers and the conduits for dispensing instant
drinks shall be carefully sanitised at the time of the
installation of the machine and at least once a week or
more frequently, according to the use of the machine
and the inlet water quality in order to provide for hygiene
on dispensing products.
It is absolutely forbidden to use water jets for
cleaning.
The parts to be cleaned are listed here below:
Powder deposit drawers, mixers and the conduit in--
tended to dispense instant drinks;
Dispensing tubes and nozzles;-
Dispensing compartment.-
To start cleaning, act as follows:
Open the cover of the mixer dispensing box and lift the-
powder outlet ports as far as the locking hook;
Remove (see fig. 9) the powder funnels, the water fun--
nels, the conveyors, the powder deposit drawers and
the impellers of whipper motors from the mixers;
Fig. 8
Sugar container1-
Sugar conveyor2-
Slide3-
Fig. 9
Powder funnel1-
Powder conveyor2-
Whipper impeller3-
Powder outlet port4-
Cover fastening magnet5-
Mixer fastening flange6-
Mixer refrigerated box cover7-

© by N&W GLOBAL VENDING S.p.A. 10 07 - 2010 3375 - 01
To disassemble the impellers, pull slightly to release-
them (fig. 10 );
Wash all the components by using sanitising products-
(observe the dosage recommended by the producer).
Make sure that all visible residuals and films are me-
chanically removed. Use pipe-cleaners or brushes, if
necessary.
Sanitise by making use of sanitising products.
Dip the components into a container with the sanitising-
solution you have prepared before for about 20’;
Reassemble the conveyors and the water funnels after-
having carefully rinsed and dried them up.
Before closing the dispensing box, lower down all
powder outlet ports.
After having assembled the parts, act as follows,
any way:
Wash the mixers and add some drops of the sanitising-
solution into the various funnels.
After having sanitised, rinse the parts abundantly to-
remove any residue of the solution in use.
All the operations requiring the machine to be
directly connected to a source of electricity must
be ONLY carried out by the personnel qualied and
informed on the specic risks involved.
Mi x e r c h a n n e l s
Use a small vacuum-cleaner or a brush to clean the fun-
nel area and the container support surface by removing
any powder residue at regular intervals.
Surfaces can be cleaned by using a wet piece of cloth.
Di s p e n s i n g c o M p a r t M e n t a n D v a n D a l -p r o o f D e -
v i c e
To disassemble the dispensing compartment, act on the
retain hook at the back to release the compartment and
let it slide on the guides.The doors intended to protect
the openings for dispensing drinks and cups require no
special maintenance. Normal cleaning is enough.
If necessary, the knurl will help you disassemble the noz-
zle support arm.
On reassembling, pay attention to the position of the cup
shift arm and to the position of the compartment on the
guides.
se r v i c e i n t e r r u p t i o n
If the machine should be o for any reason whatsoever
for a period longer than the pull dates of products, it is
necessary to act as follows:
Empty the containers completely and wash them-
carefully by using the sanitising products used for the
mixers
Empty the water circuit completely-
Before restarting operation, clean and sanitise.
Fig. 10
Fig. 11
Dispensing compartment1-
Cup shelf extraction knob2-
Support of dispensing tubes3-
Compartment fastening knurls4-
Dispensing compartment support5-
Mobile cup dispensing cover6-
Fastening for guide7-

© by N&W GLOBAL VENDING S.p.A. 11 07 - 2010 3375 - 01
Chapter 2
Installation
Installation and any subsequent maintenance opera-
tion must be carried out when the machine is live and,
therefore, by the personnel skilled and trained on the
use of the machine as well as aware of the specic risks
such a condition may involve.
The machine must be installed in a dry room, at a tem-
perature between 2° and 32°C and it can not be installed
in a room where water jets are used for cleaning (e.g.
large kitchens, etc.).
At the time of the installation, it is necessary to
completely sanitise the water circuits and the parts

bacterium that may have built up during storage.
DOOR SWITCHES
ma i N s
Whenever you open the door, a special switch will power
o the electric installation of the equipment.
To power on the machine when the door is open, just
insert the key into the slot (see g. 12).
When the door is open, you are not allowed to
access any live part. Only the parts protected by

removing the cover” will remain live inside the
machine.
Before removing these covers, it is necessary to
detach the power supply cable from the mains.
You can close the door only after having removed the
key from the door switch.
Do o r o p E N
The open door signalling switch (used on some models
only) (see g. 12) is operated by the lock by means of
the door hook device.
This switch is intended to store the door opening in the
machine statistics.

After having unpacked the machine, make sure that the
equipment is intact.
In case of doubt never use the equipment.
-
rene, nails, etc.) should be left within the reach of
children since they are potential sources of danger.
Packing materials shall be disposed of in authorised
dump sites and recyclable ones collected by specialised
companies.
Important!!
The machine shall be arranged to prevent maximum
inclination from exceeding 2°.
If necessary, level it by using the adjustable feet (see g.
13) supplied with the machine.
Fig. 12
Door switch1-
Permanently live socket (230V~ 2 A max)2-
Mains fuses3-
Card LED display holes4-
Counter5-
Door opening signalling micro (optional)6-
Service buttons.7-
Fig. 13
Adjustable foot1-

© by N&W GLOBAL VENDING S.p.A. 12 07 - 2010 3375 - 01
LABEL INSERTION
To insert the product labels, remove the metal sheet
pushbutton panel protection by loosening the fastening
screws.
Disassemble the selection keyboard after having
removed the three fastening screws by acting on xing
clips (see g. 14).
Insert the labels into the slots alternatively opening on
the right and left side.
Some buttons may not be used according to the models
(see the selection dose table).
The self-adhesive labels also supplied shall be applied
to the product containers according to the arrangement
(see the selection dose table).
Nu m E r i c s E l E c T i o N m o D E l s
To insert the selection labels, disassemble the left side
panel from the door by removing the 5 screws complete-
ly and by extracting the clips from the seats (see g. 15).
Extract the menu panel and insert the labels in the cor-
responding slots.
Some positions may not be used according to the mod-
els (see the selection dose table).
The self-adhesive labels also supplied shall be applied
to the product containers according to the arrangement
(see the selection dose table).
Reassemble everything in the reverse order.
Fig. 14
Fastening screws1-
Fixing clips2-
Selection keyboard3-
Product labels4-
Fig. 15
Fastening screws1-
Door side panel2-
Menu panel3-
Label pockets4-
Selection labels5-

© by N&W GLOBAL VENDING S.p.A. 13 07 - 2010 3375 - 01
WATER SYSTEM CONNECTION
The vending machine must be connected with the drink-
able water system according to the provisions in force in
the place of installation of the equipment.
The mains pressure must range from 0.05 to 0.85 Mpa
(0.5 8.5 bar).
Let water come out of the water network until it is limpid
and free of any trace of dirt.
Connect the water network with the union of the water
inlet solenoid valve by means of a tube that can support
the network pressure and of a type suitable for foodstus
(min. inner diameter 6 mm.) (see g. 16).
-

pr E -a r r a N g E m E N T o f W a T E r i N l E T f i l T E r s
It may be necessary to use a water inlet lter according
to inlet water quality and the presence or absence of the
cooling unit.
The machines arranged for the assembly of lters have a
” gas solenoid valve union (” for some markets) and a
pre-arrangement tube for replacement with the lter you
have chosen (see g. 17).
aN T i f l o o D D E v i c E
The water inlet solenoid valve (see gg. 16-17) is com-
plete with an antiood device that can mechanically lock
the water inlet as a result of a malfunction of the solenoid
valve or the water level control gear in the boiler.
To restore the normal operation, act as follows:
power off the machine;-
discharge water in the overflow tube;-
close the water network cock outside the machine;-
loosen the union intended to fasten the supply tube of-
the solenoid valve to discharge the residual network
pressure and tighten it again (see gg. 16-17);
open the cock and power on the machine.-
DE ca l c i f i E r
The machine is supplied without a decalcier.
If water is very hard, you can mount a decalcier.
Decalciers, available as an accessory, shall be regener-
ated according to the manufacturer’s instructions at regular
intervals.
Fig. 16
¾” gas water inlet union1-
Inlet tube union2-
Overflow tube3-
Delivery tube4-
Fig. 17
Inlet union1-
Tube pre-arrangement for filter connection2-
Water inlet solenoid valve3-
Overflow tube4-
Delivery tube5-
To the cold unit (optional)6-

© by N&W GLOBAL VENDING S.p.A. 14 07 - 2010 3375 - 01
ELECTRIC CONNECTION
The machine is arranged for electrical operation at a
230 V~ single-phase voltage and it is protected by a 15A
fuse.
For connection make sure that the rating will comply with
the mains data, in particular:
the supply voltage value shall lie within the limits rec--
ommended for the connection points;
the main switch shall be featured in such a way that it-
can support the maximum load required and to ensure
omnipolar disconnection from the mains with an open-
ing gap of the contacts of min. 3 mm.
-
ing plug shall be located in an accessible position.
The electrical safety of the machine is only ensured
when the machine is correctly and eciently grounded
according to the safety standards in force.

requirement and, in case of doubt, to require pro-
-
lation carefully.
The supply cable is of the type with a xed plug. If neces-
sary, the connection cable (see g. 18) shall be replaced
by qualied personnel by using only cables of the HO5
RN - F or HO5 V V-F or H07 RN-F type, 3x1-1.5 mm2 in
cross-section.

and/or extensions.
THE MANUFACTURER WILL DISCLAIM ALL RE-
SPONSIBILITY FOR ANY DAMAGE CAUSED BY THE
NON-OBSERVANCE OF THE PRECAUTIONS MEN-
TIONED ABOVE.
pa y m E N T s y s T E m a s s E m B l y
The machine is sold without any payment system.
As a consequence, only the installer will be liable
for any damage that may be caused to the machine
or to things and persons by an incorrect installation
of the payment system.
Mount the payment system you have selected by follow-
ing the instructions and make sure that:
- you have programmed the parameters correctly;
- regulate the reject lever in order to open the selector
completely;
- regulate the coin slide according to the coin mecha-
nism you have assembled.
Ba N k i N s T a l l a T i o N
The control system of the machine is arranged for the
bank installation with other automatic dispensers by us-
ing special kits.
This will enable the operator to use one single pay-
ment and remote connection system (GSM) for several
machines.
In case of a bank installation, the machine can be con-
gured as a “master”, i.e. as a machine controlling the
second one, or as a “slave”, i.e. as a machine controlled
by the second one.
Fig. 18
Small lift cover1-
Cable clamp2-
Mains cable3-