NAPCO EXPRESS XP-600 Installation manual

Hexadecimal Data Entry
To Enter a hexadecimal digit
enter the following:
A=

D=

B=

E=

C=

F=

Set Key
Press this key before
entering a Program-
ming Block Number.
XP-600 Programming Instructions
®
DEALER PROGRAM MODE - KEYPAD KEY DEFINITION
Note: These Programming Instruction are intended to be used in conjunction with WI847C,
please refer to WI847C for additional information, instructions and definitions.
Exiting Dealer Program Mode
(4) (5) (6) (7)
Dealer Code
Enter

Enter

+
Default Dealer Code shown in parentheses
(4) (5) (6) (7)
Dealer Code
Blank Key
Press this key to disable all fea-
tures within a LED type Program-
ming Block or to blank out digits in
a Direct Entry type Programming
Block.
1. Remove power from the panel.
2. Remove all wiring from terminal
15 (PGM) and terminal 3.
3. Connect terminal 15 (PGM) to
terminal 3.
4. Apply power to the XP-600 con-
trol panel.
5. After a few seconds the ARMED,
READY and
* SYSTEM TROU-
BLE LEDs will flash.
6. The keypad will beep 3 times
indicating the panel default val-
ues have been loaded.
7. Remove wiring between terminal
15 (PGM) and terminal 3.
8. Re-install original wiring for ter-
minal 15 (PGM) and terminal 3.
Note: Any programming in
Dealer Options 1 [96] and Dealer
Options 2 [97] will not be de-
faulted. If Dealer Code Lockout
has been programmed the panel
will not default the Dealer Code.
The Event Log will be erased
when the panel is defaulted.
DEFAULTING THE PANEL
$50('
5($'<
6<67(0 *
*
),5(
$&
=21( 
=21( 
=21( 
=21( 
=21( 
=21( 
1$3&2









Scroll Key
Use this key to scroll
through data that has been
entered in Programming
Entering Dealer Program Mode READY
ARMED ON
OFF
FLASHING
Indicates the panel is in Dealer
Program Mode. The panel is
ready for a programming block
number to be entered.
SYSTEM
9
READY
ARMED FLASHING
FLASHING
FLASHING
Indicates the panel is
Ready to exit Dealer
Program Mode. Enter
the Dealer Code to exit.
SYSTEM
9
WI847C 8/97
Entering Dealer Program Mode is not permitted while the panel
is Armed, Reporting, or the Bell Output is on. To Enter Dealer
Mode while the Bell is ON or the panel is Reporting or Armed;
power up the panel and enter Dealer Mode within the first 3
minutes. Pressing the
"
key clears the 3 minute timer.
NOTE:
After 15 minutes of keypad inactivity the keypad
will emit a steady tone indicating the panel has been
left in Dealer Program Mode. Enter Dealer Code to
exit or press the

key to return to Dealer
Program mode.
NOTE:
Wi847c
page 1 Tuesday, September 16, 1997 08:35

2
7\SHV RI 3URJUDPPLQJ %ORFNV
LED Programming Block
Enable features by pressing the key that corresponds to the associated feature; the LED will turn ON. To disable a feature press the key
again; the LED will turn OFF. To disable all features within a LED Type Programming Block press the

key; all LEDs will turn OFF.
LED Programming Block Example
Program zones 2 and 3 as
Follower Zones.
1. Enter Programming Block 02, by pressing

(Beep), then

(Beep).
2. Press the

key to select zone 2.
3. Press the

key to select zone 3.
Zone 2 and Zone 3
LEDs are ON indi-
cating that zones 2
and 3 have been
programmed as fol-
lower zones.
1LED Type
Programming
Block
Direct Entry Programming Example 2
(Hexadecimal data entry)
Program
Telephone Prefix Number
with a 9E.
1. Press

(Beep)

(Beep).
2. Press

3. Press

4. Press

2
Direct Entry Programming Block
Enter data directly. For hexadecimal entries of A-F, use the

key +

through
 ke
y
s, respectivel
y
. Use the

ke
y
to blank out di
g
its in Direct Entr
y
t
y
pe pro
g
rammin
g
blocks. Default values are shown in parentheses.
Direct Entry Programming Example 1
Pro
g
ram the panel for a 60 second
Exit Delay.
1. Press

(
Beep
)

(
Beep
)
2. Press
 .
1
0 6 0 Exit Delay, seconds
(0) (4) (5) Maximum Entry 255
10 Exit Delay
9E
44 Dialing Prefix
Direct Entry
Type
Programming
Blocks
02 Exit/Entry Follower
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
²
²
=21( 
=21( 
=21( 
=21( 
=21( 
=21( 
READY
ARMED OFF
FLASHING
FLASHINGSYSTEM
9
Indicates the panel is in
Dealer Program Mode and
the next digit entered will be
interpreted as a Hexadeci-
mal digit. Valid entries are
1-6 (A-F).
Wi847c
page 2 Tuesday, September 16, 1997 08:35

3
Viewing Data in Programming Blocks
To view data within a programming Block, enter the Program Block Number, then press the

key, continue pressing the

key until all digits within
the Programming Block have been viewed. Data will be displayed in the binary format shown in the table below:
ZONE LED ON ZONE LED OFF
0/Blank123456789 *A/0 BCDEF
ZONE 1
ZONE 2
ZONE 3
ZONE 4
For Technical As-
sistance, Contact
the Napco Toll
Free Helpline 
[phone]
*In the following Program-
ming Blocks, data that has
been entered as a ‘0’ will
be displayed as an ‘A’:
Subscriber ID Numbers,
Phone Numbers, Pager
Leading and Trailing digits
and Report Codes.
NOTE:
Example: Viewing the Dialing Prefix
A Dialing Prefix of 9E has been programmed at Programming Block Num-
ber 44 (outside access number). Follow the steps below to view the data.:
Press

to enter Programming Block 44. The 1st
digit of Programming Block 44 is displayed.
1
Press the

key to view the 2nd digit.
2
9E
44 Dialing Prefix The Following Program-
ming Options are not
permitted for UL installa-
tions: [05], [06], [23-2],
[26-3] and [26-4].
The symbol by a
programming Block indi-
cates the programming
option is not permitted
for UL installations.
NOTE:
UL
For information about
programming blocks re-
fer to XP-600 Installation
Manual WI846C.
NOTE:
ZONE 3
ZONE 1
ZONE 2
ZONE 4
Data = 9
ZONE 3
ZONE 1
ZONE 2
ZONE 4
Data = E
Wi847c
page 3 Tuesday, September 16, 1997 08:35

4
=RQH )HDWXUHV
UL
Default
OFF
OFF
ON
OFF
OFF
OFF
00 Exit/Entry Zones
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
01 Home/Away with Delay Zones
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
02 Exit/Entry Follower Zones
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
03 Auto Bypass Reentry Zones
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
04 24 Hour Protection Zones
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
05 40 ms Loop Response Zones
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
ON
ON
ON
ON
ON
ON
07 Burg (Steady) Output
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
ON
ON
ON
ON
ON
ON
08 Programmable Output (PGM)
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
UL
Default
OFF
OFF
OFF
OFF
OFF
OFF
06 Open Circuit Zones
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
See wiring
diagram for
Open Circuit
wiring.
Default
ON
ON
ON
ON
ON
ON
09 Selective Bypass
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Wi847c
page 4 Tuesday, September 16, 1997 08:35

5
Zn 1 LED ON = Momentary Keyswitch Arming
6\VWHP 7LPHV
Entry Delay, seconds
(0) (3) (0) Maximum Entry 255
11 Entry Delay
Exit Delay, seconds
(0) (4) (5) Maximum Entry 255
10 Exit Delay
Bell Time-out, minutes
(0) (0) (5) Maximum Entry 255
12 Burg (Steady) Output Time-out
Bell Time-out, minutes
(0) (0) (0) Maximum Entry 255
13 Fire (Pulsed) Output Time-out
Test Timer, days
(0) (0) (1) Maximum Entry 255
14 Test Timer Interval
Line Cut Time-to-Fail, seconds
(0) (0) (0) Enable Feature-Valid Entries 10-255
15 Line Cut Time-to-Fail (Disabled = 000)
Supervisory Timer, hours
(1) (2) Maximum Entry 26
16 Wireless Supervisory Timer
Smoke Supervisory Timer, hours
(8) Maximum Entry 8
17 Wireless Smoke Supervisory Timer
Test Timer Offset, hours
(1) (2) Maximum Entry 23
18 Test Timer Offset
6\VWHP )HDWXUHV
UL
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery and Wireless Smoke Supervisory Failure.
NOTE 3:
Cannot be programmed with any other Programmable Output (PGM) Feature.
NOTE 2:
Default
OFF
OFF
OFF
OFF
23 Programmable Output (PGM) Features 1
Zn 1 LED ON = Audio Verification
Zn 2 LED ON = *Access Output (

)
Zn 3 LED ON = *Follow Keypad Sounder
Zn 4 LED ON = *Keyfob/Keyswitch Chirp
*See Note 2
Default
OFF
OFF
OFF
OFF
24 Programmable Output (PGM) Features 2
Zn 1 LED ON = Fire
Zn 2 LED ON = AUX
Zn 3 LED ON = Panic
Zn 4 LED ON = Test Timer
Default
OFF
OFF
OFF
OFF
26 Miscellaneous Features 2
Zn 2 LED ON = Reserved
Zn 3 LED ON = Inhibit Fail to Communicate
Zn 4 LED ON = Inhibit Low Battery Display
UL
Default
OFF
OFF
OFF
OFF
25 Programmable Output (PGM) Features 3
Zn 1 LED ON = AC Fail
Zn 2 LED ON = Low Battery
Zn 3 LED ON = *Trouble
Zn 4 LED ON = Armed
*See Note 3
Default
OFF
OFF
OFF
ON
20 Keypad Features 1
Zn 1 LED ON = *Keypad Fire (

)
Zn 2 LED ON = *Keypad AUX (

)
Zn 3 LED ON = *Keypad Panic (

)
*See Note 1
Default
OFF
OFF
ON
ON
21 Keypad Features 2
Zn 1 LED ON = Audible panic
Zn 2 LED ON = Exit/Entry with Urgency
Zn 3 LED ON = Display Bypass (ARMED)
Zn 4 LED ON = Disable Code Entry Beeps
Default
ON
OFF
OFF
ON
22 Miscellaneous Features 1
Zn 1 LED ON = Abort Delay
Zn 2 LED ON = Easy Arm/Easy Exit
Zn 3 LED ON = Swinger Shutdown
Zn 4 LED ON = Bell on Line Cut (Armed)
Additional programming required for reporting, see Blocks [36]&[56].
UL Installations: If Keypad Fire [20-1] is enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
NOTE 1:
Zn 4 LED ON = *Ambush (6th User Code)
UL
Wi847c
page 5 Tuesday, September 16, 1997 08:35

6
7HOHSKRQH 1XPEHU  3URJUDPPLQJ
30 Subscriber ID Number
[0] Disabled
[1] Ademco Slow
[2] Radionics Slow
[3] Silent Knight Fast
[4] Universal High Speed
[5] Reserved
[6] Point ID
[7] Pager
32 Receiver Format
(4)
31 Telephone Number 1
NOTE:
Requires features to be enabled, see block [20].
NOTE 1:
A fixed Dial Tone Detection (E) is included prior to the
Dialing Prefix
(Block
Number 44)
.
Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select
No Dial Tone Detection
in
Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery, Wireless Smoke Supervisory Failure.
ZONE 3 TX LOW BATTERY “RF TRAN LOW BAT, ZN03”
SMOKE 2 LOW BATTERY “RF TRAN LOW BAT, ZN10”
NOTE 2:
Default
OFF
OFF
OFF
OFF
OFF
OFF
39 Opening Closing Report, Telco 1
Zn 1 LED ON = User 1 Reporting
Zn 2 LED ON = User 2 Reporting
Zn 3 LED ON = User 3 Reporting
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
Zn 6 LED ON = User 6 Reporting
Default
ON
ON
ON
ON
ON
ON
34 Zone Report, Telco 1
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
35 Zone Restore Report, Telco 1
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
ON
36 System Reporting, Telco 1
Zn 1 LED ON = *KP Fire (

)
Zn 2 LED ON = *KP AUX (

)/Ambush
Zn 3 LED ON = *KP Panic (

)
Zn 4 LED ON = Test Timer
*See Note 1
Default
ON
ON
OFF
OFF
37 System Reporting, Telco 1
Zn 1 LED ON = AC Fail Report (15 min. report delay)
Zn 2 LED ON = Low Battery Report
Zn 3 LED ON = *Trouble Report
Zn 4 LED ON = Fire Report
*See Note 2
Default
OFF
OFF
OFF
OFF
38 System Restore Report, Telco 1
Zn 1 LED ON = AC Restore Report
Zn 2 LED ON = Battery Restore Report
Zn 3 LED ON = Trbl Restore Report
Zn 4 LED ON = Fire Restore Report
Default
OFF
OFF
ON
OFF
33 Receiver Options
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
Zn 2 LED ON = Sumcheck
Zn 3 LED ON = Single Digit
Zn 4 LED ON = No Handshake
Wi847c
page 6 Tuesday, September 16, 1997 08:35

7
%DFNXS 7HOHSKRQH 3URJUDPPLQJ 3DJHU 3URJUDPPLQJ
47 Leading Digits
48 Trailing Digits
(0) (0) (0) (0)
*(C) *See Note 1
Dialing Prefix for Telco 1, Telco 2
& Telco 3.
40 Subscriber ID Number (Telco 2)
41 Telephone Number 2
[1] Ademco Slow
[2] Radionics Slow
[3] Silent Kni
g
ht Fast
[4] Universal Hi
g
h Speed
[5] Reserved
[6] Point ID
[7] Pa
g
er
42 Receiver Format
(4)
44 Dialing Prefix
C = TouchTone #. This is the t
y
pical terminatin
g
di
g
it for
most pa
g
in
g
s
y
stems. Recommended, but ma
y
not be
required b
y
pa
g
in
g
s
y
stem. D = 2 second dela
y
.
NOTE 1:
Default
OFF
OFF
ON
OFF
43 Receiver Options
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
Zn 2 LED ON = Sumcheck
Zn 3 LED ON = Sin
g
le Di
g
it
Zn 4 LED ON = No Handshake
Default
ON
OFF
ON
OFF
45 Communicator Features 1
Zn 1 LED ON = Communicator Enabled
Zn 2 LED ON = DTMF w/ Rotary Back up
Zn 3 LED ON = DTMF only
Zn 4 LED ON = Backup to Telco 2
Default
OFF
OFF
OFF
OFF
46 Communicator Features 2
Zn 1 LED ON = No Dial Tone Detection
Zn 2 LED ON = 2:1 Rotary Dialin
g
Zn 3 LED ON = Backup if < 4 attempts
Zn 4 LED ON = Reserved Default
OFF
OFF
OFF
OFF
49 Pager Option
Zn 1 LED ON = Skip Alarm Data
Zn 2 LED ON = Reserved
Zn 3 LED ON = Reserved
Zn 4 LED ON = Reserved
NOTE:
A fixed Dial Tone Detection (E) is included prior to the
Dialing Prefix
(Block
Number 44)
.
Pro
g
rammin
g
an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select
No Dial Tone Detection
in
Communicator Features (Block Number 46). Pro
g
ram a D if a 4 second
dela
y
is required.
Wi847c
page 7 Tuesday, September 16, 1997 08:35

8
7HOHSKRQH 1XPEHU  3URJUDPPLQJ
50 Subscriber ID Number
[0] Disabled
[1] Ademco Slow
[2] Radionics Slow
[3] Silent Knight Fast
[4] Universal High Speed
[5] Reserved
[6] Point ID
[7] Pager
52 Receiver Format
(4)
31 Telephone Number 3
NOTE:
Requires features to be enabled, see block [20].
NOTE 1:
A fixed Dial Tone Detection (E) is included prior to the
Dialing Prefix
(Block
Number 44)
.
Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select
No Dial Tone Detection
in
Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
NOTE 2:
Default
OFF
OFF
OFF
OFF
OFF
OFF
59 Opening Closing Report, Telco 3
Zn 1 LED ON = User 1 Reporting
Zn 2 LED ON = User 2 Reporting
Zn 3 LED ON = User 3 Reporting
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
Zn 6 LED ON = User 6 Reporting
Default
OFF
OFF
OFF
OFF
OFF
OFF
54 Zone Report, Telco 3
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
OFF
OFF
OFF
55 Zone Restore Report, Telco 3
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Default
OFF
OFF
OFF
ON
56 System Reporting, Telco 3
Zn 1 LED ON = *KP Fire (

)
Zn 2 LED ON = *KP AUX (

)/Ambush
Zn 3 LED ON = *KP Panic (

)
Zn 4 LED ON = Test Timer
*See Note 1
Default
OFF
OFF
OFF
OFF
57 System Reporting, Telco 3
Zn 1 LED ON = AC Fail Report (15 min. report delay)
Zn 2 LED ON = Low Battery Report
Zn 3 LED ON = *Trouble Report
Zn 4 LED ON = Fire Report
*See Note 2
Default
OFF
OFF
OFF
OFF
58 System Restore Report, Telco 3
Zn 1 LED ON = AC Restore Report
Zn 2 LED ON = Battery Restore Report
Zn 3 LED ON = Trbl Restore Report
Zn 4 LED ON = Fire Restore Report
Default
OFF
OFF
ON
OFF
53 Receiver Options
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
Zn 2 LED ON = Sumcheck
Zn 3 LED ON = Single Digit
Zn 4 LED ON = No Handshake Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery, Wireless Smoke Supervisory Failure.
ZONE 3 TX LOW BATTERY “RF TRAN LOW BAT, ZN03”
SMOKE 2 LOW BATTERY “RF TRAN LOW BAT, ZN10”
Wi847c
page 8 Tuesday, September 16, 1997 08:35

9
5HSRUW &RGHV
60 Zone Report Codes
Zone 1 Alarm Code
(3) Zone 2 Alarm Code
(3) Zone 3 Alarm Code
(3) Zone 4 Alarm Code
(3) Zone 5 Alarm Code
(3) Zone 6 Alarm Code
(3)
The second digit of the
Re-
port Code
is the number of
the zone that is reporting.
For example zone 5 report
code (default of 3) would be
35.
61 Point ID Report Codes
Zone 1 Alarm Code
(3) Zone 2 Alarm Code
(3) Zone 3 Alarm Code
(3) Zone 4 Alarm Code
(3) Zone 5 Alarm Code
(3) Zone 6 Alarm Code
(3)
1FIRE
2 PANIC
3 BURGLARY
4 HOLDUP
5 GENERAL ALARM
6 RESERVED
7 GAS ALARM
8 HEAT ALARM
9 RESERVED
A AUXILIARY
B 24 HOUR ALARM
62 Zone Codes
Zone 1, 2, 3, 4, 5 & 6 Restore Code
(E) Zone 1, 2, 3, 4, 5 & 6 Trouble Code
(F)
63 System Report Codes
Keypad Fire (

)
(1) (1) Keypad AUX (

)
(2) (3) Keypad Panic (

)
(2) (1) Test Timer
(F) (F) AC Fail
(F) (9) Low Battery
(F) (8) *Trouble
(F) (1) Fire
(1) (1)
64 System Restore Code
(E)
65 Opening and Closing Code
(C) Closing Code
(B) Opening Code
66 Ambush Report Code
(2) (2)
Enhanced Communicator Features
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure, Wire-
less Smoke Low Battery and Wireless Smoke Supervisory Failure.
NOTE 1:
NOTE:
*See Note 1
Default
OFF
OFF
OFF
OFF
67 Telephone Number 1
Zn 1 LED ON = Opening after Alarm (Cancel Code)
Zn 2 LED ON = Conditional Closing
Zn 3 LED ON = Reserved
Zn 4 LED ON = Reserved
Default
OFF
OFF
OFF
OFF
68 Telephone Number 3
Zn 1 LED ON = Opening after Alarm (Cancel Code)
Zn 2 LED ON = Conditional Closing
Zn 3 LED ON = Reserved
Zn 4 LED ON = Reserved
Wi847c
page 9 Tuesday, September 16, 1997 08:35

10
:LUHOHVV
7UDQVPLWWHUV
:
71 Zone 1
RF ID # Point
:
72 Zone 2
:
73 Zone 3
:
74 Zone 4
:
75 Zone 5
:
76 Zone 6
Enter the RF ID# located on
the Transmitter, Key Fob and
Smoke Detector labels.
RF ID # XXXXXX:X
Enter the point number to be
associated with the zone. If only
one point of GEM-TRANS2 is
used, enter a 1in this location.
For GEM-GB, GEM-DT, GEM-
PIR enter a 1in this location.
:
81 Keyfob 1
.H\IREV
AUX 1 AUX 2RF ID #
:
82 Keyfob 2
:
83 Keyfob 3
:
84 Keyfob 4
AUX 1 & 2
Programming
1 Panic
2 AUX
3 Bell ON
4 PGM
5 Instant
6 Access on PGM
7 Full Set System
8 Interior
6PRNH 'HWHFWRUV
RF ID #
Hexadecimal Data Entry
To Enter a hexadecimal digit enter the following: A=

B=

C=

D=

E=

F=

Programming Example
Map point 1 of a window door transmitter, with RF ID# 0012B0:0
to Zone 3.
1. Enter Dealer Mode.
2. Enter

(beeps)

(beeps)
3. Enter

4. Enter

(beeps)
Note: If the RF ID# in step 3 is not entered correctly the
keypad will emit a 1 second tone indicating incorrect entry.
Repeat steps 2 - 4 above.
Hexadecimal B Entry
0012B0:0 1
73 Zone 3
:
85 Smoke 1
:
86 Smoke 2
:
87 Smoke 3
:
88 Smoke 4
Wi847c
page 10 Tuesday, September 16, 1997 08:35