natus Otometrics Bio-logic AuDX PRO FLEX User manual

Natus Medical Denmark ApS. [phone]. [email protected]om
Natus Medical Incorporated. 1-800-289-2150. otoorder[email protected]om
www.otometrics.com
Bio-logic®AuDX PRO FLEX®
Diagnostic OAE and audiometry
Quick start guide
Doc. No.7-26-1375-EN/00
Part No.7-26-13705-EN
Bio-logic®

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
2
Bio-logic®
Turning On/Off, and charging the device
Start menu
On/off button
on right side
Current time
Battery status
Select patient
Additional
information on
options for current
screen
Turn off device
Customize settings
Power supply
connector
Connect the headphones to the blue connector.
Select Audio: Threshold preset from the start menu.
Select the ear on which you want to start the test.
The test screen will be displayed
Testing: Audiometry

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
3
Bio-logic®
Stimulus on indicator
Select the ear to test
Select the stimulus
levels
Additional information
about options for
current screen
Change settingsEnter masking mode
Stop test
Select the frequency
Test screen
Audiometry test results
Green background
indicates range of
normal hearing
Print results to a label
or to a pdf file or full
page report on PC.

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
4
Bio-logic®
Screening audiometry
Audiometry screening
Test screen
Connect the headphones to the blue connector.
Select Audiometry screening Preset from the start menu.
Select the ear on which you want to start the test.
The test screen will be displayed.
Select the stimulus levels
Select the type of
stimulus presentation
Select the ear to test
Select the
frequency
Press to present
the stimulus
Stop test Additional information
about options for
current screen

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
5
Bio-logic®
As you present the
stimulus, the current level
will be displayed in the
corresponding square.
Once the hearing status
for a frequency has been
identified, move on to
the next frequency.
Once the test is finished, you can save the results, print to a label (a label printer is required)
or print to a pdf file.
Connect the red probe to the red
connector and select one of the
Presets for DPOAE Quick. To perform
binaural testing, also connect the
blue probe to the blue connector.
Select the appropriate ear tip
size and place it on the probe
tip. Insert the probe in the ear
making sure that the ear tip
fits tightly into the ear canal.
Select the test ear by pressing
either the Right or Left
button, or the Right + Left
button for binaural testing.
Cartoon mode will start
the test showing a cartoon
instead of the progress bar.
Once all frequencies have been tested for one
ear, you can test the other ear
Tapping twice on a
square will display NR
(no response)
Tap three times to get
back to blank square
Distrotion Product Otoacoustic Emissions (DPOAE): Screening

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
6
Bio-logic®
Overall screening test result
Probe fit override
for patients with PE
tubes or middle ear
perforations
Progress for each
tested frequency
Overall test progress
Noise floor level
Red (right ear) or blue (left
ear) bars show response
amplitude. Grey bars show
noise amplitude
Switch to results of the other ear
after both ears have been tested
Print results to a label or
to a pdf file
Note: These circles indicate
that other screens are available
to view. Swipe your finger right
or left to get other views
Retest frequencies that
did not pass
Test other ear
Green check marks indicate
valid response. Red circles
indicate no valid response
DPOAE screening test results
Please note that the initial result screen depends on the module settings in "DPOAE Preferences"
A calibration will be performed prior to measurement. A green light indicates successful calibration.
After successful ear probe calibration, the test will start automatically.

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
7
Bio-logic®
Connect the red probe to the
red connector and select one of
the Preset protocols for DPOAE
Diagnostic. To perform binaural
testing, also connect the blue
probe to the blue connector.
A calibration will be performed prior to measurement. A green light indicates successful calibration.
After successful ear probe calibration, the test will start automatically.
Select the appropriate ear tip
size and place it on the probe
tip. Insert the probe in the ear
making sure that the ear tip fits
tightly into the ear canal.
Select the test ear by pressing
either the Right or Left button,
or the Right + Left button for
binaural testing.
Cartoon mode will start the test
showing a cartoon instead of the
progress bar, this can be changed
during the test by tapping on the
plane icon at the bottom of the
device screen.
DPOAE diagnostic / high resolution
Probe fit override for patients with
PE tubes or middle ear perforations Skip a frequency
Pause/resume test
Stop test
Progress for each
tested frequency
in each ear
Switch to
cartoon mode
Overall test progress
Noise floor level

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
8
Bio-logic®
Note: These circles indicate
that other screens are available
to view. Swipe your finger
right or left to get other views
Print results to a label or to a pdf file Test other ear
Green check marks indicate
valid sponse
Red or blue bars indicate response,
grey bars indicate noise
High resolution test results (4 PPO)
Outcome for each test sorted by
f2 and L2. Multilevel test results
shown. Tap on screen to view
details for each level tested.
Numeric values shown in table
format
DPOAE diagnostic / high resolution test results

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
9
Bio-logic®
Connect the red probe to the red
connector and select one of the
Presets for DPOAE Threshold. To
perform binaural testing, also
connect the blue probe to the
blue connector.
Select the appropriate ear tip size
and place it on the probe tip.
Insert the probe in the ear making
sure that the ear tip fits tightly into
the ear canal.
Select the test ear by pressing
either the Right or Left button,
or the Right + Left button for
binaural testing.
Cartoon mode will start the test
showing a cartoon instead of the
progress bar, this can be changed
during the test by tapping on the
plane icon at the bottom of the
device screen.
DPOAE threshold
A calibration will be performed prior to measurement. A green light indicates successful calibration.
After successful ear probe calibration, the test will start automatically.
Probe fit override for patients with
PE tubes or middle ear perforations
Skip a frequency
Pause/resume test
Stop test
Progress for each
tested frequency
in each ear
cartoon mode
for children
Noise floor level

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
10
Bio-logic®
Green background
indicates range of
normal hearing
Print results to a label
or to a pdf file
DPOAE threshold test results

Quick Guide:
Bio-logic®AuDX PRO FLEX®Diagnostic OAE and audiometry
Otometrics - Next generation Bio-logic products
11
Bio-logic®
Quick Guide Information
Release date: 2017-01-11
Revision: 02
Valid from: Firmware Rev. 2.1, Mira PC Software Rev. 1.6.4
Applies to: Model: SOH100098, web description SOH03
All mentioned items, products, brands and trademarks are registered or owned by the mentioned companies.
All information, illustrations, and specifications provided within this manual are based on the latest product
information available at the time of publication. PATH medical reserves the right to make changes at any time
without notice.
Please note that not all products displayed on our webpage or advertising materials are available in all
territories.
Please contact your local distributor or PATH medical for further information.
The latest revision of the Quick Start Guide is available online at www.pathme.de/download.
Errors and omissions excepted.
Copyright Notice
No part of this manual may be reproduced, translated, stored, or transmitted, in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent
of PATH medical GmbH.
Copyright © 2016 PATH medical GmbH
PATH medical GmbH
Landsberger Straße 65
82110 Germering
Germany
Tel: [phone]
Fax: [phone]
Internet: www.pathme.de