NEC DTR-IR-2 User manual

Dterm Analog Cordless II
®
(DTR-1R-2)
User’s Manual

Table of Contents [i]
TABLE OF CONTENTS
Welcome/Features/Terminology.........1
WELCOME .......................................................1
FEATURES .......................................................1
TERMINOLOGY .................................................1
Controls & Functions...........................2
Displays and Icons...............................3
ANIMATION DISPLAYS ......................................3
SOFT KEY FUNCTION .......................................4
Getting Started .....................................5
SETTING UP THE PHONE ..................................5
MOUNTING THE BASE UNIT ON AWALL ............8
Standard Wall Plate Mounting ..............................8
Direct Wall Mounting ............................................8
CONNECTING THE CHARGER ............................9
REGISTER THE HANDSET .................................9
MAIN MENU OPTIONS ....................................10
Default Settings ..................................................10
SETTING MENU OPTIONS ...............................10
Using the interface .............................................10
Handset Setup ....................................................11
Programming your Voice Mail Access
Number .........................................................11
Selecting a Ringer Tone ................................11
Distinctive Ringer Setup ................................11
Setting the AutoTalk ......................................11
Setting the Anykey Answer ...........................12
Setting the True Banner ................................12
Selecting a Language ...................................12
Adjusting the LCD Contrast ...........................12
Setting the Key Touch Tone ..........................12
Setting the Animation Screen ........................12
Global Setup ...................................................... 13
Setting Day and Time ....................................13
Setting the Dial Mode ....................................13
Setting Voice Mail Tone .................................13
Deregister the Handset ..................................13
Basics..................................................15
MAKING AND RECEIVING CALLS .................... 15
REDIALING ACALL ........................................ 16
Deleting a Redial Record ................................... 16
Storing a Redial Record ..................................... 16
ADJUSTING THE RINGER, AND EARPIECE AND
SPEAKER VOLUME ........................................ 16
Ringer Volume ................................................... 16
Earpiece and Speaker Volume .......................... 16
TEMPORARILY MUTING THE RINGER ............... 17
MUTE MICROPHONE ...................................... 17
TONE DIALING SWITCH-OVER ........................ 17
TRAVELING OUT OF RANGE ........................... 17
PRIVACY MODE ............................................. 17
Phonebook..........................................19
PHONEBOOK (STORING PHONE NUMBERS,
NAMES, DISTINCTIVE RINGS AND SPEED DIAL) 19
CHAIN DIALING ............................................. 20
STEPS FOR ENTERING NAMES AND SPECIAL
CHARACTERS ................................................ 20
If You Make a Mistake while Entering a Name .. 21
VIEWING THE PHONEBOOK ............................ 21
MAKING CALLS USING THE PHONEBOOK ....... 22
From Standby Mode .......................................... 22
From Talk Mode ................................................. 22
SPEED DIALING ............................................. 22

[ii] TableofContents
EDITING OR ERASING ASTORED NAME, PHONE
NUMBER, DISTINCTIVE RING AND SPEED DIAL 22
Caller ID .............................................. 23
VIEWING THE CALLER ID LIST ....................... 23
DELETING ACALLER ID MESSAGE ................. 23
Deleting Information from the Caller ID List ....... 23
Deleting all Caller ID Names/Numbers .............. 23
USING THE CALLER ID MESSAGE LIST ........... 24
Calling a Party from the Caller ID List ............... 24
Additional Information ...................... 25
CHANGING THE DIGITAL SECURITY CODE ....... 25
FIND HANDSET .............................................. 25
INSTALLING THE BELTCLIP ............................. 25
To Attach the Beltclip ........................................ 25
To Remove the Beltclip ..................................... 25
HEADSET INSTALLATION ................................ 25
NOTE ON POWER SOURCES ........................... 26
Battery Replacement and Handling ................... 26
Power Failure .................................................... 26
Low Battery Alert ............................................... 26
Cleaning the Battery Charging Contacts ........... 27
GENERAL INFORMATION .................................27
AC Adapter Information .....................................27
Battery Information .............................................27
Replacement Item Part Numbers .......................27
Troubleshooting ................................ 29
LIQUID DAMAGE .............................................30
Precautions and Warranty ................ 31
I.C. Notice ........................................... 33
Terminal Equipment ...........................................33
Radio Equipment ...............................................33
Memory List........................................ 35
Flow Chart .......................................... 37
MAIN MENU FLOW CHART ..............................37

[ 1 ]
Welcome/Features/Terminology
Welcome
Congratulations on your purchase of this NEC Unified Solutions, Inc. Digital Expandable Cordless
Telephone System! This unit is different from conventional cordless telephones. You can now place
a fully-featured cordless handset anywhere in your home or office where AC power is available to
connect the handset chargers.
• Some illustrations in this manual may differ from the actual unit for explanation purposes.
Features
• 5.8GHz Digital Expandable
• Hands-Free Duplex Speakerphone in the Handset
•CallerID
• 100 programmable Memory Locations
• Trilingual Display Options (English, French and Spanish)
• 20 Distinctive Ring Options (10 ringer tones and 10 melody ringers)
• Mute and Hold Features
• Battery Level Indicator
• Clock Display
•AnimationDisplays
This series features AutoTalk™and AutoStandby™. AutoTalk allows you to answer a call by just
removing the handset from the cradle so you don't have to waste time pushing buttons.
AutoStandby allows you to hang up by simply returning the handset to the cradle.
To protect you against mis-billed calls that might result from your phone being activated by other
equipment, this series has Random Code™digital security, which automatically selects one of
more than 10,000,000 digital security codes for the handset and base.
Digital Spread Spectrum Technology uses a wider frequency band than standard digital
transmissions. The result is a more secure conversation with the clarity of digital sound, extended
range, and minimal interference from other cordless phones.
IntegriSoundTM Built in sound quality which provides life-like conversations.1
Terminology
•Standby Mode - The handset is not in use, and talk/flashor speaker has not been pressed. No dial tone is present.
•Talk Mode - The handset is not in the cradle, and talk/flash or speaker has been pressed, enabling a dial tone.
Talk appears on the display.
1. AutoTalk, AutoStandby, IntegriSound, and Random Code are trademarks of Uniden America.

[ 2 ] Controls & Functions
Controls & Functions
1. Handset Antenna
2. Beltclip Hole
3. Speakerphone Speaker and Ringer
4. Handset Battery Compartment
5. New Message LED
6. Handset Earpiece
7. LCD Display
8. soft Keys (page 4)
9. /vol /(volume up/down) (page 10 & page 16)
10.
*
/tone/< (page 17 & page 20)
11. speaker (page 15)
12. intcom/hold
13. Headset Jack Cover
14. talk/flash (page 15)
15. end (page 15)
16. cid (page 23)
17. #/> (page 20)
18. phonebook (page 19)
19. Handset Microphone
20. Handset Charging Contacts
2
1
4
3
5
6
7
8
9
10
11
12
1
9
2
0
1
4
1
7
1
8
1
5
1
6
1
3
22
23
24
25 26
21
PowerMax 5.8GHz
21. Base Charging Contacts
22. Base Antenna
23. Charge LED
24. find handset (page 25)
25. DC IN 9V Jack
26. TEL LINE Jack

Displays & Icons [ 3 ]
Displays and Icons
Example of the standby mode display
Animation Displays
The handsets have a variety of animation displays. Below are examples of the animation screens and
what they mean:
Turning on the phone Hanging up the phone Confirmation (Done!) Deleting (Deleted!)
Making a call Find Handset/Paging the Handset
Also, the animation display changes depending on the ringer volume setting.
Out of Range Unavailable Low Battery
ICON Appears During DESCRIPTION
Standby/Talk Battery icons indicate the handset battery status. This icon changes depending on
the battery status (empty, low, medium and full).
Standby The Ringer off icon indicates that ringer is turned off.
Talk The Mute icon appears when you mute the handset.
Talk The Speaker icon appears when the handset speaker phone is used.
Talk The Privacy icon appears when the Privacy Mode is turned on.
570#
*CPFUGV
0GY%+&
4'&+#. /'07
Ringer off icon (when the ringer is off)/ day of the week and time / battery icon
Handset ID and Banner
Number of new Caller ID calls received (If there are no new Caller ID
messages,
the Handset ID appears here.)
9GNEQOG
2NGCUG9CKV

'PF
&QPG &GNGVGF
6CNM

/76' %9&: 24+8#%;
2CIKPI
4KPIGT8QNWOG
4'&+#. /'07
4KPIGT8QNWOG
4'&+#. /'07
?
4KPIGT8QNWOG
4'&+#. /'07
1WV1H4CPIG
4'&+#. /'07
7PCXCKNCDNG
4'&+#. /'07
.QY$CVVGT[

[ 4 ] Displays & Icons
Soft Key Function
"Soft" keys are keys that change function during the operation of the phone. There are three soft keys
on each handset. Soft Keys allow you to:
- Access the main menu - Access stored Caller ID messages
- Store or edit phone numbers - Redial one of the last three numbers dialed from the handset
The soft keys will not appear while the handset is charging.
The function of each soft key is determined by the icon that appears directly above it. For example,
when the handset is in standby mode, pressing soft key 1 will redial the last dialed number. When the
handset is in talk mode, pressing soft key 1 will mute the microphone.
Complete information on the features controlled by the soft keys can be found under each feature.
In standby mode In talk mode
570#
*CPFUGV
0GY%+&
4'&+#. /'07
Soft key 1 Soft key 2 Soft key 3
6CNM

/76' /'07
%9&:
Soft key 1 Soft key 2 Soft key 3

Getting Started [ 5 ]
GETTING STARTED
Getting Started
Setting up the Phone
Do the following steps:
A. Choose the best location
B. Install the rechargeable battery pack into the handset.
C. Connect the base unit
A. Choose the best location
Before choosing a location for your new phone, read “Installation
Considerations” on page 32. Here are some important guidelines you should
consider:
• Avoid heat sources, such as radiators, air ducts, and sunlight.
• Avoid television sets and other electronic equipment.
• Avoid microwave ovens
• Avoid noise sources, such as a window by a street with heavy traffic.
• Avoid excessive moisture, extremely low temperatures, dust, mechanical vibration, or shock.
• Avoid personal computers.
• Avoid other cordless telephones.
• Choose a central location.
For maximum range:
• Keep the antenna free of obstruction.
• When the handset is not in use place the handset in an upright position.
• Do not hold the handset where you would block the signal.
• Metal and reinforced concrete may affect cordless telephone performance.
note
Correct
I
ncorrect

[ 6 ] Getting Started
B. Install the Rechargeable Battery Pack into the Handset
The handset is powered by a rechargeable battery pack. The battery recharges
automatically when the handset is placed in the base unit. To maximize the charge capacity
of your battery pack, DO NOT plug the telephone cord into the base unit and wall jack
until the battery is fully charged.
1) Press down on the handset battery case cover (use the finger indention for
a better grip) and slide the cover downward to remove.
2) Turn the battery pack so that the connector with the red and black wires is
near the jack inside the battery compartment. Match the connector's wire
colors to the polarity label in the battery compartment (the connector
notches fit into the grooves of the jack only one way). Push the battery
pack connector into the jack until it clicks into place.
3) Make sure you have a good connection by gently pulling on the battery
wires. If the connection is secure, the battery jack will remain in place.
4) Place the battery case cover back on the handset and slide it upwards until
it clicks into place.
note • Use only the NEC rechargeable battery pack supplied with your cordless telephone.
• Replacement battery packs are also available. Contact your NEC Representative.

Getting Started [ 7 ]
C. Connect the Base Unit
1) Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC
wall outlet.
Connect the AC adapter to a continuous power supply (i.e., an outlet that is
not controlled by a switch).
2) Set the base on a desk or tabletop, and place the handset in the base unit.
Place the base unit close to the AC outlet so that you can unplug the AC
adapter easily.
3) Make sure that the charge LED illuminates.
If the LED does not illuminate, check to see that the AC adapter is plugged
in and the handset makes good contact with the base charging contacts.
4) After install the battery pack in the handset, charge your handset for at
least 15~20 hours before plugging into the phone line.
5) Once the handset battery pack is fully charged, connect the telephone line
cord to the TEL LINE jack and to a telephone outlet.
If your telephone outlet is not modular, contact your NEC Representative for
assistance.
• Use only the supplied AC adapter. Do not use any other AC adapter.
• Place the power cord so that it does not create a trip hazard or where it could
become chafed and create a fire or electrical hazard.
note

[ 8 ] Getting Started
Mounting the Base Unit on a Wall
Standard Wall Plate Mounting
This phone can be mounted on any standard wall plate.
1 Make the AC adapter and the telephone line cord through the hole on the wall
mount adapter.
2 Plug the AC adapter into the DC IN 9V jack.
3 Plug the telephone line cord into the TEL LINE jack.
4 Slide the wall mount adapter into the notches on the base.
5 Plug the AC adapter into a standard 120V AC wall outlet. Hook the cord on the
notch of the wall mount adapter.
6 Plug the telephone line cord into the telephone outlet. Hook the cord on the notch
of the wall mount adapter.
7 Align the mounting slots on the base with the mounting posts on the wall. Then
push in and down until the telephone is firmly seated.
Direct Wall Mounting
If you do not have a standard wall plate, you can mount your phone directly to the wall. Before doing
this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting
screws into the wall.
• Try to mount your telephone within 5 feet of a working phone jack to avoid excessive lengths.
• Make sure the wall material is capable of supporting the weight of the base and handset.
• Use #10 screws (minimum length of 1 & 3/8 inches) with anchoring devices suitable for the wall material where the base
unit will be placed.
1 Insert two mounting screws into the wall (with their appropriate anchoring device),
3 & 15/16 inches apart. Allow about 1/8 of an inch between the wall and screw
heads for mounting the telephone.
2 Refer to steps 1 through 7 above for mounting the telephone.
To remove, push u
p
a tab on the wall
mount adapter as
shown.
DO NOT use an AC outlet controlled by a wall switch.
!

Getting Started [ 9 ]
Connecting the Charger
1 Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC wall
outlet.
2 Set the charger on a desk or tabletop, and place the handset in the charger
with the keypad facing forward. (See “B. Install the Rechargeable Battery Pack
into the Handset” on page 6.)
Register the Handset
Handsets supplied with the phone are registered to the base by the factory.
When charged, pre-registered handsets display a handset ID number. Handsets
that have not been registered display
Place handset on main base to register .
When you register a handset to the base, the handset ID will be assigned.
1 Before registering the handset, the battery pack MUST be charged for 15~20 hours.
2 Place the handset in the main base unit to begin registration.
3 While the handset is registering,
Handset Registering will appear in the LCD. When Registration
Complete
is displayed, the handset has been registered to the base. If Registration Failed appears, please
try these steps again.
Charge the handset battery pack for at least 15~20 hours before
using your new cordless telephone for the first time.
note
2NCEGJCPFUGV
QPOCKPDCUG
VQTGIKUVGT
/76' %9&:
The handset can be registered when the main base is in standby
mode.
note

[ 10 ] Getting Started
Main Menu Options
Your phone has five main menu options: Handset Setup, Global Setup and Deregister HS.
Default Settings
The default settings set from the factory match the features that most people use. You may not need to
change them. However, there are a number of options you must set and entries you must make in
memory to take full advantage of all the phone features. The table below lists the default settings.
Setting Menu Options
Using the interface
Below are some tips for using the software interface on your phone.
• Press the MENU soft key to access the main menu.
•Use
/vol/∧and /vol/∨to scroll through options.
• Press the OK soft key to make a selection.
• Press the BACK soft key to return to the previous screen.
• Press end to exit the menu.
Function Default Settings Function Default Settings
Edit Voice Mail None Day & Time SUN 12:00 AM
Ringer Tone Flicker CW / CWDX CW on/CWDX off
Distinctive Ring On Area code None
Auto Talk Off Dial Mode Tone
Anykey Answer Off Voice Mail Tone On
Banner “ “
Language (LCD) English
Contrast level 5
Key touch tone On
Animation Screen On
• For Global Setup and Deregister HS menu options, make sure the line is not in use and the handsets are within
range of the base.
• Main menu flow chart is provided on page 37.
note

Getting Started [ 11 ]
Handset Setup
The following submenu options must be set separately for each handset.
Programming your Voice Mail Access Number
1 Press the MENU soft key. Select the Handset Setup menu, and then the Edit
Voice Mail submenu.
Edit V_mail No. appears.
2 Enter your personal access number using the number keypad (0-9),
*
/tone/<, #/>,
the DELETE soft key, or the PAUSE soft key (up to 20 digits).
3 Press the OK soft key. You will hear the confirmation tone.
To delete the current Voice Mail Access Number, delete all numbers in step2 using the DELETE soft key
and the OK soft key.
Selecting a Ringer Tone
Ringer Tone lets you choose from 10 ringer tones or 10 melodies:
• Ringers (Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder)
• Melodies (Beethoven's Symphony #9 [Beethoven9], For Elise [Elise], We Wish You A Merry Christmas [Merry- Xmas],
Home Sweet Home [Hm Swt Hm], Lorri Song #6 [Lorri Song], When Irish Eyes Are Smiling [Irish Eyes], Aura Lee, Let Me
Call You Sweet Heart [Sweetheart], Star Spangled Banner [Star Spngl], Old MacDonald [Old MacDld]).
1 Press the MENU soft key. Select the Handset Setup menu, and then the Ringer
Tone submenu.
2Press/vol
∧or /vol/∨to move the pointer. You will hear the ringer or melody as
you scroll through the options.
3 When you reach the ringer tone you want, press the OK soft key. You will hear a
confirmation tone.
Distinctive Ringer Setup
Distinctive Ringer allows you to assign a designated ring tone to a stored phonebook number (100 stored
locations available). When a call is received and the Caller ID information matches the information in one of
the phonebook memory locations, the phone uses the distinctive ring assigned to that particular Caller. You
can assign distinctive rings to multiple phonebook memory locations. Switching the setting to Distinctive Off
disables distinctive ringing: all incoming calls will have a normal ring tone. Switching to Distinctive On
activates all programmed distinctive ring memory locations.
1 Press the MENU soft key. Select the Handset Setup menu, and then the
Distinctive Ring submenu.
2Press
/vol/∧or /vol/∨to select On or Off .
3 Press the OK soft key. You will hear a confirmation tone.
Setting the AutoTalk
Autotalk allows you to answer the phone simply by removing the handset from the
cradle. You do not have to press any buttons to answer the call.
1 Press the MENU soft key. Select the Handset Setup menu and then the AutoTalk
submenu.
2Press
/vol/∧or /vol/∨to select On or Off .
3 Press the OK soft key. You will hear a confirmation tone.
'FKV8AOCKN0Q
㨫
&'.'6' &'.'6' 1-
2#75'
4KPIGT6QPGU
(NKEMGT
%NCVVGT
$#%- &'.'6' 1-
&KUVKPEVKXG4KPI
1P
1HH
$#%- &'.'6' 1-
#WVQ6CNM
1P
1HH
$#%- &'.'6' 1-

[ 12 ] Getting Started
Setting the Anykey Answer
Any Key Answer allows you to answer the phone by pressing any number key,
*
/tone/<, or #/> on the handset.
1 Press the MENU soft key. Select the Handset Setup menu, and then the Anykey
Answer submenu.
2Press
/vol/∧or /vol/∨to select On or Off .
3 Press the OK soft key. You will hear a confirmation tone.
Setting the True Banner
True Banner lets you customize the name your handset displays.
The name will be displayed on the LCD screen during Standby Mode, Intercom, Intercom Hold, Room Monitor
and Copy Phonebook operation. The banner name will be displayed on the receiving handset as well.
1 Press the MENU soft key. Select the Handset Setup menu, and then the Banner
submenu.
2 Use the number keypad (0~9),
*
/tone/<, #/>, or the DELETE soft key to enter or
edit the name.
3 Press the OK soft key. You will hear a confirmation tone.
Selecting a Language
Language selects which language the menu display will use. Choose from English, French, or Spanish.
1 Press the MENU soft key. Select the Handset Setup menu, and then the
Language submenu.
2Press
/vol/∧or /vol/∨to choose “English”, “Français” (French), or
“Español” (Spanish).
3 Press the OK soft key. You will hear a confirmation tone.
Adjusting the LCD Contrast
Contrast adjusts the handset LCD brightness. Choose one of the 10 levels for optimum viewing.
1 Press the MENU soft key. Select the Handset Setup menu and then the
Contrast submenu.
2Press
/vol/∧or /vol/∨to adjust the contrast of the LCD (10 levels.)
3 Press the OK soft key. You will hear a confirmation tone.
Setting the Key Touch Tone
Key Touch Tone is the tone your keypad makes when keys are pressed. You can turn this tone on or off.
1 Press the MENU soft key. Select the Handset Setup menu and then the Key
Touch Tone submenu.
2Press /vol/∧or /vol/∨to select
On or Off .
3 Press the OK soft key. You will hear a confirmation tone.
Setting the Animation Screen
The Animation screen displays animation on the handset LCD. The animations will
be displayed on the LCD screen during a call, ringer volume setting, when you
hang up, and so on.
1 Press the MENU soft key. Select the Handset Setup menu and then the
Animation Screen submenu.
2Press
/vol/∧or /vol/∨to select On or Off .
3 Press the OK soft key. You will hear a confirmation tone.
See "Animation Displays"on page 3 for all the available screens.
#P[MG[#PUYGT
1P
1HH
$#%- &'.'6' 1-
AAAAAAAAAA
$CPPGT
/QOU2JQPG 
$#%- &'.'6' 1-
.CPIWCIG
'PINKUJ
(TCP㩟CKU
$#%- 1-
%QPVTCUV

$#%- 1-
-G[6QWEJ6QPG
1P
1HH
$#%- &'.'6' 1-
4KPIGT8QNWOG
4'&+#. /'07
#PKOCVKQP5ETGGP
1P
1HH
$#%- &'.'6' 1-

Getting Started [ 13 ]
Global Setup
If you change one of the global settings, you change that setting for all registered handsets. Only one
handset can change global settings at a time.
Setting Day and Time
Day & Time sets the day and time of your display.
1 Press the MENU soft key. Select the Global Setup menu, and then the Day &
Time submenu option.
2Press
/vol/∧or /vol/∨to select the day of the week, and then the →soft key.
3Press
/vol/∧or /vol/∨to set hour, and then press the →soft key.
4Press /vol/∧or /vol/∨ to set minute, and then press the →soft key.
5Press
/vol/∧or /vol/∨to choose AM or PM , and then press the SAVE soft key.
Day & Time idle timeout is two minutes.
Setting the Dial Mode
Sets the dial mode to tone or pulse. Most phone systems use tone dialing; the default setting is tone dialing.
Set the dialing mode to match the dialing system used by your local phone service.
• If you are not sure of your dialing system, set the unit to tone dialing. Make a trial call. If the call connects, leave the
setting as is; otherwise set the unit to pulse dialing.
• If your phone system requires pulse dialing and you need to send DTMF tones in certain situations during a call, you
can switch over to tone dialing (refer to “Tone Dialing Switch-over” on page 17).
1 Press the MENU soft key. Select the Global Setup menu, and then the Dial Mode
submenu.
2Press
/vol/∧or /vol/∨to select Tone or Pulse (the initial setting is Tone).
3 Press the OK soft key. You will hear a confirmation tone.
Setting Voice Mail Tone
Voice Mail Tone sets the voice mail tone. If your service does not support SDT message signal, set your
VMWI (Visual Message Waiting Indicator) not to detect SDT message signal.
1 Press MENU soft key. Select the Global Setup menu, and then the Voice Mail Tone Submenu.
2Press /vol/∧or /vol/∨to set the voice message indication (SDT message
signal) to On or Off.
3 Press the OK soft key. You will hear a confirmation tone.
Deregister the Handset
Deregister HS clears the handset’s ID from the main base unit or the base ID from the handset. You will
usually only deregister the handset if you are having a problem with your phone or if you need to change the
digital security code. (see page 25).
1 In standby mode, select Deregister HS in the menu and press the OK soft key.
Deregister HS? appears.
2Press
/vol/∧or /vol/∨to select Yes and then the OK soft key.
When deregistration is complete you will hear a confirmation tone, and
Deregistration Complete appears.
3 After deregistering the handset, place the handset to the base to register. You must reregister the handset
before you can use it.
&C[6KOG
/10#/
=?
$#%- 5#8'
&KCN/QFG
6QPG
2WNUG
$#%- &'.'6' 1-
8QKEG/CKN6QPG
1P
1HH
$#%- &'.'6' 1-
&GTGIKUVGT*5!
;GU
0Q
$#%- &'.'6' 1-

[ 14 ] Getting Started
THIS PAGE INTENTIONALLY LEFT BLANK

Basics [ 15 ]
BASICS
Basics
Making and Receiving Calls
With the handset's duplex speakerphone, you can have hands-free
conversations.
The icon appears on the display screen during hands-free conversations.
You can easily switch a call from normal conversation to hands-free
conversation. To switch a call, press speaker during the call.
From the Handset From the Handset
Normal conversation Hands-free
conversation
To answer a call
Handset On the Cradle
Pick up the handset (AutoTalk is:
on) or pick up the handset and
press talk/flash (AutoTalk is: off).
Handset Off the Cradle
Press any number key,
*
/tone/<,
or #/> (Any Key Answer), or
press talk/flash.
Handset Off the Cradle
Press speaker.
To make a call
Handset Off the Cradle
1) Press talk/flash.
2) Listen for the dial tone.
3) Dial the number.
OR
Dial the number, and then press
talk/flash.
Handset Off the Cradle
1) Press speaker.
2) Listen for the dial tone.
3) Dial the number.
OR
Dial the number, and then
press speaker.
To hang up Press end or return the handset to the cradle (AutoStandby).
To enter a pause
within the dialing
sequence
When you dial the number in standby mode, press the PAUSE
soft key.
P appears in the display, which represents a pause.
6CNM

/76' /'07
For best performance talk alternately with the caller in a quiet room.
You can decrease the speaker volume if you or the other party has
difficulty hearing.
note
• To set "Autotalk", see page 11 or to set "Anykey Answer" see page 12.
• The handset microphone is located at the bottom of the handset (see "Controls & Functions" on page 2).
Position yourself as near to the handset as possible and speak clearly.
note

[ 16 ] Basics
Redialing a Call
The last three phone numbers dialed can be quickly redialed from the handset.
Redial numbers stored in the handset are independent from each other.
1 With the phone in standby mode, press the REDIAL soft key.
2 Press /vol/∧or /vol/∨to scroll through the last three dialed numbers.
3 Press talk/flash or speaker on the handset. The selected number is dialed.
4 To hang up, press end.
Deleting a Redial Record
1 With the phone in standby mode, press the REDIAL soft key.
2 Press /vol/∧or /vol/∨repeatedly to display the number to be deleted.
3 Press the DELETE soft key.
4 Press /vol/∧or /vol/∨to choose
Yes .
5 Press the OK soft key. The redialed number is deleted.
Storing a Redial Record
1 With the phone in standby mode, press the REDIAL soft key.
2 Press /vol/∧or /vol/∨repeatedly to display the number to be stored.
3 Press the STORE key.
Store/Edit Name appears.
4 To complete the setting, follow the steps 3~8 in "Phonebook (Storing Phone Numbers, Names, Distinctive
Rings, and Speed dial)" on page 19.
Adjusting the Ringer, and Earpiece and Speaker Volume
Ringer Volume
In standby mode, press the volume up key or volume down key on the handset
to select one of three ringer volume (Off, Low, or High).
Earpiece and Speaker Volume
You can select from among six volume levels on the handset. Pressing the
volume up key or volume down key during a call will change the earpiece or speaker volume. This
setting will remain in effect after the telephone call has ended.
If you press the volume up key when the earpiece is at the maximum volume level, an error tone
sounds.
The error tone also sounds if you press the volume down key at the lowest volume.
4GFKCN

$#%- &'.'6'
&'.'6'
&'.'6'
5614'
4GFKCN

$#%- 5614'
4GFKCN

$#%- 5614'
/vol/ or /vol/
/vol/ or /vol/
&GNGVG4GFKCN!
;GU
0Q
$#%- $#%- 1-
• If the number exceeds 32 digits, only the first 32 digits are retained in redial memory.
• If the redial memory is empty, you will hear a beep.
note