NETGEAR ProSafe WNAP320 User manual

350 East Plumeria Drive
San Jose, CA 95134
USA
January 26, 2011
202-10724-01
v1.0
ProSafe Wireless-N Access
Point WNAP320
Reference Manual

2 |
ProSafe Wireless-N Access Point WNAP320 Reference Manual
©2011 NETGEAR, Inc. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form or by any means without the written permission of NETGEAR, Inc.
Technical Support
Thank you for choosing NETGEAR. To register your product, get the latest product updates, or get support online,
visit us at http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR
Phone (Other Countries): See Support information card.
Trademarks
NETGEAR, the NETGEAR logo, ReadyNAS, ProSafe, Smart Wizard, Auto Uplink, X-RAID2, and NeoTV are
trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT, and Vista are
registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or
trademarks of their respective holders.
Statement of Conditions
To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes
to the products described in this document without notice. NETGEAR does not assume any liability that may occur
due to the use, or application of, the product(s) or circuit layout(s) described herein.
Revision History
Publication Part Number Version Publish Date Comments
202-10724-01 v1.0 January 2011 First publication

Contents |3
Contents
Chapter 1 Introduction
About the ProSafe Wireless-N Access Point WNAP320 . . . . . . . . . . . . . . .6
What Is In the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
System Requirements . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Key Features and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Supported Standards and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . .8
Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
802.11b/g/n Standards–Based Wireless Networking . . . . . . . . . . . . . . .10
Autosensing Ethernet Connections with Auto Uplink . . . . . . . . . . . . . . .10
Hardware Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Top Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Bottom Panel with Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Chapter 2 Installation and Basic Configuration
What You Need before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Wireless Equipment Placement and Range Guidelines. . . . . . . . . . . . .14
Ethernet Cabling Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
LAN Configuration Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Computer Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Install and Configure the Wireless Access Point . . . . . . . . . . . . . . . . . . . .16
Connect the Wireless Access Point to Computer. . . . . . . . . . . . . . . . . .16
Log In to the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Configure Basic General System Settingsand Time Settings . . . . . . . .19
Configure IP Settings and Optional DHCP Server Settings . . . . . . . . . .21
Configure Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Test Basic Wireless Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Mount the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Ceiling Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Desk Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Chapter 3 Wireless Configuration and Security
Wireless Data Security Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Before You Change the SSID, WEP, and WPA Settings. . . . . . . . . . . .38
Configure and Enable Security Profiles . . . .. . . . . . . . . . . . . . . . . . . . .39
Configure RADIUS Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Restrict Wireless Access by MAC Address . . . . . . . . . . . . . . . . . . . . . . . .50

4| Contents
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Schedule the Wireless Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Configure Basic Wireless Quality of Service . . . . . . . . . . . . . . . . . . . . . . .52
Chapter 4 Management
Enable Remote Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
SNMP Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Secure Shell and Telnet Management. . . . . . . . . . . . . . . . . . . . . . . . . .57
Upgrade the Wireless Access Point Software . . . . . . . . . . . . . . . . . . . . . .58
Manage the Configuration File or Reset to Factory Defaults . . . . . . . . . . .60
Save the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Restore the Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Restore the Wireless Access Point to the Factory Default Settings. . . .62
Reboot the Wireless Access Point without Restoring the
Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Change the Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Enable the Syslog Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Monitor the Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
View System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Monitor Wireless Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
View the Activity Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Traffic Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Enable Rogue AP Detection and Monitor Access Points. . . . . . . . . . . . . .72
Enable and Configure Rogue AP Detection. . .. . . . . . . . . . . . . . . . . . .72
View and Save Access Point Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Chapter 5 Advanced Configuration
Spanning Tree Protocol and 802.1Q VLAN . . . . . . . . . . . . . . . . . . . . . . . .76
Hotspot Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Configure Advanced Wireless Settings . . . . . .. . . . . . . . . . . . . . . . . . . . .79
Configure Advanced QoS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Configure Wireless Bridging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Configure a Point-to-Point Wireless Network. . . . . . . . . . . . . . . . . . . . .85
Configure a Point-to-Multipoint Wireless Network . . . . . . . . . . . . . . . . .88
Configure the Wireless Access Point for Repeater Mode . . . . . . . . . . .92
Configure the Wireless Access Point for Client Mode . . . . . . . . . . . . . .96
Chapter 6 Troubleshooting
Basic Functioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
No LEDs Are Lit on the Wireless Access Point . . . . . . . . . . . . . . . . . . .98
The Active LED or the LAN LED Is Not Lit. . . . . . . . . . . . . . . . . . . . . . .99
The WLAN LED Does Not Light Up . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
You Cannot Access the Internet or the LAN from a
Wireless-Capable Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
You Cannot Configure the Wireless Access Point from a Browser . . . . .100
When You Enter a URL or IP Address a Time-Out Error Occurs. . . . . . .101
Troubleshooting a TCP/IP Network Using the Ping Utility . . . . . . . . . . . .101

Contents |5
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Testing the LAN Path to Your Wireless Access Point . . . . . . . . . . . . .101
Testing the Path from Your Computer to a Remote Device . . . . . . . . .102
Problems with Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Use the Packet Capture Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Appendix A Supplemental Information
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Appendix B Command-Line Reference
Appendix C Notification of Compliance
Index

Chapter 1. Introduction |6
1
1. Introduction
This chapter introduces the ProSafe Wireless-N Access Point WNAP320 and describes some of
the key features. This chapter includes the following sections:
• About the ProSafe Wireless-N Access Point WNAP320 on this page
• What Is In the Box? on page 7
• System Requirements on page 7
• Key Features and Standards on page 7
• Hardware Description on page 10
About the ProSafe Wireless-N Access Point WNAP320
The ProSafe Wireless-N Access Point WNAP320 is the basic building block of a wireless
LAN infrastructure. It provides connectivity between wired Ethernet networks and
radio-equipped wireless notebook systems, desktop systems, print servers, and other
devices.
The wireless access point provides wireless connectivity to multiple wireless network devices
within a fixed range or area of coverage—interacting with a wireless network interface card
(NIC) through an antenna. Typically, an individual in-building wireless access point provides
a maximum connectivity area of about a 500-foot radius. The ProSafe Wireless-N Access
Point WNAP320 can support up to 64 users simultaneously in a range of several hundred
feet.
The ProSafe Wireless-N Access Point WNAP320 acts as a bridge between the wired LAN
and wireless clients. Connecting multiple wireless access points through a wired Ethernet
backbone can further increase the wireless network coverage. As a mobile computing device
moves out of the range of one wireless access point, it moves into the range of another. As a
result, wireless clients can freely roam from one wireless access point to another and still
maintain seamless connection to the network.
The autosensing capability of the ProSafe Wireless-N Access Point WNAP320 allows packet
transmission at up to 300 Mbps, or at reduced speeds to compensate for distance or
electromagnetic interference.

Chapter 1. Introduction |7
ProSafe Wireless-N Access Point WNAP320 Reference Manual
What Is In the Box?
The product package should contain the following items:
• ProSafe Wireless-N Access Point WNAP320
• Power adapter and cord (12 VCD, 1.0A)
• Straight-through Category 5 Ethernet cable
• NETGEAR WNAP320 Wireless-N Access Point Installation Guide
• Resource CD, which includes this manual
• Wall-mount kit made up of brackets and hardware
Contact your reseller or customer support in your area if there are any missing or damaged
parts.
Refer to the NETGEAR website at http://kbserver.netgear.com/main.asp for the telephone
number of customer support in your area. You should keep the Installation Guide, along with
the original packing materials, and use the packing materials to repack the wireless access
point if you need to return it for repair.
To qualify for product updates and product warranty, NETGEAR encourages you to register
on the NETGEAR website at http://my.netgear.com/registration/login.aspx.
System Requirements
Before installing the wireless access point, make sure that your system meets these
requirements:
• A 10/100/1000 Mbps local area network device such as a hub or switch
• The Category 5 UTP straight-through Ethernet cable with RJ-45 connector included in the
package, or one like it
• A 100–120V, 50–60 Hz AC power source
• A Web browser for configuration, such as Microsoft Internet Explorer 6.0 or later, or
Mozilla 1.5 or later
• At least one computer with the TCP/IP protocol installed
• An 802.11b/g- or 802.11n/g-compliant device, such as the NETGEAR WNDA3100
wireless adapter
Key Features and Standards
The ProSafe Wireless-N Access Point WNAP320 is easy to use and provides solid wireless
and networking support. It also offers a wide range of security options.

8| Chapter 1. Introduction
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Supported Standards and Conventions
The ProSafe Wireless-N Access Point WNAP320 supports the following standards and
conventions:
• Standards compliance.The wireless access point complies with the IEEE 802.11 b/g
standards for wireless LANs, and is Wi-Fi certified for 802.11n standard.
• Full WPA and WPA2 support. The wireless access point provides WPA and WPA2
enterprise-class strong security with RADIUS and certificate authentication as well as
dynamic encryption key generation. The WPA-PSK and WPA2-PSK preshared key
authentication is without the overhead of RADIUS servers but with all of the strong
security of WPA.
• Multiple BSSIDs. The wireless access point supports multiple BSSIDs. When a wireless
access point is connected to a wired network and a set of wireless stations, it is called a
basic service set (BSS). The basic service set identifier (BSSID) is a unique identifier
attached to the header of packets sent over a WLAN that differentiates one WLAN from
another when a mobile device tries to connect to the network.
The multiple BSSID feature allows you to configure up to eight SSIDs on your wireless
access point and assign different configuration settings to each SSID. All the configured
SSIDs are active, and the network devices can connect to the wireless access point by
using any of these SSIDs.
• DHCP client support.DHCP provides a dynamic IP address to PCs and other devices
upon request. The wireless access point can act as a client and obtain information from
your DHCP server; it can also act as a DHCP server and provide network information for
wireless clients.
• SNMP Support.Support for Simple Network Management Protocol (SNMP)
Management Information Base (MIB) management.
• 802.1Q VLAN (virtual LAN) support. A network of computers that behave as if they are
connected to the same network even though they might actually be physically located on
different segments of a LAN. VLANs are configured through software rather than
hardware, which makes them extremely flexible. VLANs are very useful for user and host
management, bandwidth allocation, and resource optimization.
Key Features
The ProSafe Wireless-N Access Point WNAP320 provides solid functionality, including the
following features:
• Multiple operating modes:
-Wireless access point. Operates as a standard 802.11b/g/n wireless access point.
-Point-to-point bridge. In this mode, the wireless access point communicates only
with another bridge-mode wireless station or wireless access point. Network
authentication should be used to protect this communication.
-Point-to-multipoint bridge. Select this only if this wireless access point is the master
for a group of bridge-mode wireless stations. The other bridge-mode wireless stations

Chapter 1. Introduction |9
ProSafe Wireless-N Access Point WNAP320 Reference Manual
send all traffic to this master, and do not communicate directly with each other.
Network authentication should be used to protect this traffic.
-Wireless repeater. In this mode, the wireless access point does not function as an
access point but communicates only with wireless stations that function in repeater
mode, point-to-point bridge mode, and point-to-multipoint-bridge mode. Network
authentication should be used to protect this communication.
-Client. In this mode, the wireless access point functions as a client bridge only, and
sends all traffic to a remote wireless access point or peer device.
• Hotspot settings. You can allow all HTTP (TCP, port 80) requests to be captured and
redirected to the URL you specify.
• Upgradeable firmware. Firmware is stored in a flash memory. You can upgrade it easily,
using only your Web browser, and you can upgrade it remotely. You can also use the
command-line interface.
• Rogue AP detection.The Rogue AP filtering feature ensures that unknown APs are not
given access to any part of the LAN.
• Access control.The Access Control MAC address filtering feature can ensure that only
trusted wireless stations can use the wireless access point to gain access to your LAN.
• Security profiles.When using multiple BSSIDs, you can configure unique security
settings (encryption, SSID, and so on) for each BSSID.
• Hidden mode. The SSID is not broadcast, assuring only clients configured with the
correct SSID can connect.
• Configuration backup. Configuration settings can be backed up to a file and restored.
• Secure and economical operation. Adjustable power output allows more secure or
economical operation.
• Power over Ethernet. Power can be supplied to the wireless access point over the
Ethernet port from any 802.3af-compliant midspan or end-span source.
• Autosensing Ethernet connection with Auto Uplink™ interface. Connects to
10/100/1000 Mbps IEEE 802.3 Ethernet networks.
• LED indicators. Power/Test, Active, LAN, and WLAN for each radio mode are easily
identified.
• Wi-FI Multimedia (WMM) support. WMM is a subset of the 802.11e standard. WMM
allows wireless traffic to have a range of priorities, depending on the kind of data.
Time-dependent information, like video or audio, has a higher priority than normal traffic.
For WMM to function correctly, wireless clients must also support WMM.
• Quality of Service (QoS) support. You can configure parameters that affect traffic
flowing from the wireless access point to the client station and traffic flowing from the
client station to the wireless access point. The QoS feature allows you to prioritize traffic,
such as voice and video traffic, so that packets do not get dropped.
• VLAN security profiles. Each security profile is automatically allocated a VLAN ID when
the security profile is modified.

10 | Chapter 1. Introduction
ProSafe Wireless-N Access Point WNAP320 Reference Manual
802.11b/g/n Standards–Based Wireless Networking
The ProSafe Wireless-N Access Point WNAP320 provides a bridge between wired Ethernet
LANs and 802.11b/g- and 802.11n-compatible wireless LAN networks. It provides
connectivity between wired Ethernet networks and radio-equipped wireless notebook
systems, desktop systems, print servers, and other devices. Additionally, the wireless access
point supports the following wireless features:
• Aggregation support
• Reduced InterFrame spacing support
• Multiple input, multiple output (MIMO) support
• Distributed coordinated function (CSMA/CA, back-off procedure, ACK procedure,
retransmission of unacknowledged frames)
• RTS/CTS handshake
• Beacon generation
• Packet fragmentation and reassembly
• Auto or long preamble
• Roaming among wireless access points on the same subnet
Autosensing Ethernet Connections with Auto Uplink
The ProSafe Wireless-N Access Point WNAP320 can connect to a standard Ethernet
network. The LAN interface is autosensing and capable of full-duplex or half-duplex
operation.
The wireless access point incorporates Auto UplinkTM technology. The Ethernet port
automatically senses whether the Ethernet cable plugged into the port should have a
“normal” connection such as to a computer or an “uplink” connection such as to a switch or
hub. That port then configures itself correctly. This feature also eliminates any concerns
about crossover cables, as Auto Uplink accommodates either type of cable to make the right
connection.
Hardware Description
This section describes the top and rear hardware functions of the ProSafe Wireless-N Access
Point WNAP320.

Chapter 1. Introduction |11
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Top Panel
The ProSafe Wireless-N Access Point WNAP320 LEDs are described in the following figure
and table:
Figure 1.
Table 1. Top Panel LEDs
Item LED Description
1Power/Test Off Power is off.
On (green) Power is on.
Amber, then blinking
green A self-test is running or software is being loaded.
During startup, the LED is first steady amber, then
goes off, and then blinks green before turning steady
green after about 45 seconds. If after 1 minute the
LED remains amber or continues to blink green, it
indicates a system fault.
2Active Off No Ethernet traffic is detected or no link is detected.
On or blinking (green) Ethernet traffic is detected.
3LAN Off 10 Mbps or no link is detected.
Amber 10/100 Mbps link is detected.
Green 1000 Mbps link is detected.
4WLAN Off Wireless LAN is not ready or no wireless activity is
detected.
On or blinking (green) Wireless LAN is ready or wireless activity is detected.
1234

12 | Chapter 1. Introduction
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Rear Panel
Figure 2.
The rear panel functions of the ProSafe Wireless-N Access Point WNAP320 are described in
the following list:
1. Reverse SMA connector for an optional 2.4-GHz antenna.
2. Factory default Reset button. Using a sharp object, press and hold this button for about
5 seconds to reset the wireless access point to factory defaults settings. All configuration
settings are lost, and the default password is restored. For more information, see Restore
the Wireless Access Point to the Factory Default Settings on page 62.
3. Console port for connecting to an optional console terminal. The port has a DB9 male
connector and supports the following settings: 9600 K default baud rate, (8) data bits, no (N)
parity bit, and one (1) stop bit.
4. 10/100/1000BASE-T Gigabit Ethernet (RJ-45) port with Auto Uplink (Auto MDI-X) with
IEEE 802.3af Power over Ethernet (PoE) support for connection to a switch or router.
5. Cable security lock receptacle for an optional lock.
6. Power socket for a 12 VDC, 1A power adapter.
7. Reverse SMA connector for an optional 2.4-GHz antenna.
123 4 567

Chapter 1. Introduction |13
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Bottom Panel with Product Label
The product label on the bottom of the wireless access point’s enclosure displays factory
default settings, regulatory compliance, and other information:
Figure 3.

Chapter 2. Installation and Basic Configuration |14
2
2. Installation and Basic Configuration
This chapter describes how to install and configure your access point for wireless connectivity to
your LAN. This basic configuration will enable computers with 802.11b/g or 802.11n wireless
adapters to connect to the Internet, or access printers and files on your LAN. In planning your
wireless network, consider the level of security required. Chapter 3, Wireless Configuration and
Security, describes how to set up wireless security for your network. This chapter includes the
following sections:
• What You Need before You Begin on this page
• Install and Configure the Wireless Access Point on page 16
• Test Basic Wireless Connectivity on page 27
• Mount the Wireless Access Point on page 28
Note: In this chapter and in all further chapters, the WNAP320 is referred
to as the wireless access point.
What You Need before You Begin
You need to consider the following guidelines and requirements before you can set up your
wireless access point. See also System Requirements on page 7.
Wireless Equipment Placement and Range Guidelines
The range of your wireless connection can vary significantly based on the location of the
wireless access point. The latency, data throughput performance, and notebook power
consumption of wireless adapters also vary depending on your configuration choices.
Note: Failure to follow these guidelines can result in significant
performance degradation or inability to wirelessly connect to the
wireless access point. For complete performance specifications,
see Appendix A, Supplemental Information.

Chapter 2. Installation and Basic Configuration |15
ProSafe Wireless-N Access Point WNAP320 Reference Manual
For best results, place your wireless access point according to the following general
guidelines:
• Near the center of the area in which your PCs will operate.
• In an elevated location such as a high shelf where the wirelessly connected PCs have
line-of-sight access (even if through walls).
• Away from sources of interference, such as PCs, microwaves ovens, and 2.4-GHz
cordless phones.
• Away from large metal surfaces or water.
• Placing an external antenna in a vertical position provides best side-to-side coverage.
Placing an external antenna in a horizontal position provides best up-and-down
coverage. (An external antenna does not come standard with the WNAP320 wireless
access point.)
• If you are using multiple wireless access points, it is better if adjacent wireless access
points use different radio frequency channels to reduce interference. The recommended
channel spacing between adjacent wireless access points is five channels (for example,
use channels 1 and 6, or 6 and 11, or 1 and 11).
The time it takes to establish a wireless connection can vary depending on both your security
settings and placement. WEP connections can take slightly longer to establish. Also, WEP
encryption can consume more battery power on a notebook computer.
Ethernet Cabling Requirements
The wireless access point connects to your LAN using twisted-pair Category 5 Ethernet cable
with RJ-45 connectors.
LAN Configuration Requirements
For the initial configuration of your wireless access point, you need to connect a computer to
the wireless access point.
Note: For assistance with DHCP configuration, see the Preparing Your
Network document that you can access from Related Documents in
Appendix A.
Computer Hardware Requirements
To connect to the wireless access point on your network, each computer must have a
802.11b/g or 802.11n wireless adapter installed.

16 | Chapter 2. Installation and Basic Configuration
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Install and Configure the Wireless Access Point
Before installing the wireless access point, make sure that your Ethernet network is up and
working. You will be connecting the wireless access point to the Ethernet network. Then
computers with 802.11b/g or 802.11n wireless adapters will be able to communicate with the
Ethernet network.
In order for this to work correctly, verify that you have met all of the system requirements,
shown in System Requirements on page 7.
Install and configure your wireless access point in the order of the following sections:
1. Connect the Wireless Access Point to Computer on this page.
2. Log In to the Wireless Access Point on page 18.
3. Configure Basic General System Settings and Time Settings on page 19.
4. Configure IP Settings and Optional DHCP Server Settings on page 21
5. Configure Basic Wireless Settings on page 23.
Connect the Wireless Access Point to Computer
Tip: Before you place the wireless access point in an elevated position that is
difficult to reach, first set up and test the wireless access point to verify
wireless network connectivity.
To set up the wireless access point:
1. Unpack the box and verify the contents.
2. Prepare a computer with an Ethernet adapter. If this computer is already part of your
network, record its TCP/IP configuration settings. Configure the computer with a static IP
address of 192.168.0.210 and 255.255.255.0 as the subnet mask.
3. Connect an Ethernet cable from the wireless access point to the computer (point Ain the
following figure).
4. Securely insert the other end of the cable into the wireless access point’s Ethernet port
(point Bin the following figure).
.

Chapter 2. Installation and Basic Configuration |17
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Figure 4.
5. Turn on your computer.
6. Connect the power adapter to the wireless access point.
Tip: The wireless access point supports Power over Ethernet (PoE). If you
have a switch that provides PoE, you will not need to use the power
adapter to power the wireless access point. This can be especially
convenient when the wireless access point is installed in a high location
far away from a power outlet.
7. Verify the following:
Power/Test LED.The Power/Test LED blinks when the wireless access point is
first turned on. (To be exact, during startup, the LED is first steady amber, then
goes off, and then blinks green.) After about 45 seconds, the LED should stay lit
(steady green). If after 1 minute the Power/Test LED is not lit or is still blinking,
check the connections and see if the power outlet is controlled by a wall switch
that is turned off.
Active LED.The Active LED is lit or blinks green when there is Ethernet traffic.
LAN LED. The LAN LED indicates the LAN speed: green for 1000 Mbps, amber
for 100 Mbps, and no light for 10 Mbps. If the LAN LED is not lit, make sure that
the Ethernet cable is securely attached at both ends.
WLAN LED. The WLAN LED is lit or blinks green when the wireless LAN (WLAN)
is ready.
A
B
Ethernet cable
Ethernet port
WNAP320

18 | Chapter 2. Installation and Basic Configuration
ProSafe Wireless-N Access Point WNAP320 Reference Manual
Log In to the Wireless Access Point
The default IP address of your wireless access point is http://192.168.0.100. The wireless
access point is set, by default, for the DHCP client to be disabled.
To log in to the wireless access point:
1. Open a Web browser such as Microsoft Internet Explorer 6.0 or later, or Mozilla Firefox
1.5 or later.
2. Connect to the wireless access point by entering its default address of http://192.168.0.100
into your browser.
The Login screen opens:
Figure 5.
3. Enter the default user name of admin and the default password of password.
4. Click Login. The Web browser displays the basic General system settings screen under the
Configuration tab of the main menu as shown in Figure 8 on page 19.
Web Management Interface
The navigation tabs across the top of the Web Management Interface provide access to all
the configuration functions of the wireless access point, and remain constant. The menu
items in the blue bar change according to the navigation tab that is selected.
Figure 6.

Chapter 2. Installation and Basic Configuration |19
ProSafe Wireless-N Access Point WNAP320 Reference Manual
The bottom right corner of all screens that allow you to make configuration changes show the
Apply and Cancel buttons, and on several screens the Edit button.
Figure 7.
These buttons have the following functions:
• Edit. Allows you to edit the existing configuration.
• Cancel. Cancels all configuration changes that you made on the screen.
• Apply. Saves and applies all configuration changes that you made on the screen.
Configure Basic General System Settings and Time Settings
Note: After you have successfully logged in to the wireless access point,
the basic General system settings screen displays.
To configure basic system settings:
1. Select Configuration > System > Basic > General. The basic General system settings
screen displays:
Figure 8.

20 | Chapter 2. Installation and Basic Configuration
ProSafe Wireless-N Access Point WNAP320 Reference Manual
2. Specify the fields as explained in the following table:
3. Click Apply to save your settings.
To configure time settings:
1. Select Configuration > System > Basic > Time. The Time screen displays:
Figure 9.
2. Specify the fields as explained in the following table:
Table 2. Basic General System Settings
Field Description
Access Point Name This unique name is the wireless access point NetBIOS name. The name is printed
on the rear label of the wireless access point. The default is netgearxxxxxx, where
xxxxxxx represents the last 6 digits of the wireless access point MAC address. You
can replace the default name with a unique name up to 15 characters long. The
access point name can be retrieved through SNMP.
Country/Region From the Country/Region drop-down list, select the country where the wireless
access point is installed.
Note: Itmightnotbe legal tooperatethiswirelessaccesspointinaregionotherthan
one of those identified in this field.
Table 3. Time System Settings
Field Description
Time Zone Select the time zone to match your location.
Current Time This is a nonconfigurable field that displays the current date and time.
NTP Client Enable the Network Time Protocol (NTP) client to synchronize the time of the
wireless access point with an NTP server. By default the Enable radio button is
selected.