NEUTRIK powerCON TRUE1 TOP NAC3FX-W-TOP User guide

20
250
P S
EJET
NAC3FX-W
NAC3FX-W
40 - 50 mm
NAC3FX-W-TOP powerCON TRUE1 TOP
| ® ®
R
[0.32"]
8 mm
[0.787”]
20 mm
[0.9”]
PE 23 mm
Separate the
housing from the
bushing (cable
remain in bushing)
B
Approval based:
Rating:
Cable Type:
Cable O.D.:
VDE
EN 60320-1
250 V ac / 16 A
2
H05VV-F3G 1.0 mm , Length max. 2 m
2
H05VV-F3G 1.5 - 2.5 mm
2
H07RN-F3G 1.5 mm
6.0 - 12.0 mm
UL 60320-1
CAN/CSA-C22.2 No. 60320-1
250 V ac / 20 A
SJTOW, SJOOW 3 x 12 AWG
6.0 - 12.0 mm
VDE
EN 60320-1
UL 60320-1
CAN/CSA-C22.2 No. 60320-1
Place chuck over the
cable.
Prepare cable as
shown.
D
C
Page 1BDA 541
Recommendation:
Wire Pulling Lubricant - LUB-I/0.95
TM
from 3M
i
AInsert cable into the bushing and housing.
Note: “Apply cable pulling
lubricant to cable jacket.”
C
[0.32"]
8 mm
[0.787”]
20 mm
[0.9”]
PE 23 mm
20
250
P S
EJET
NAC3FX-W
NAC3FX-W
NAC3PX-TOP
NAC3MPX-TOP
NAC3MPX-WOT-TOP
NAC3FPX-TOP
NAC3FPX-WOT-TOP
NAC3FPX-ST-TOP
Power OUT
Power OUT
NAC3FX-W-TOP
(Connector)
NAC3MX-W-TOP
(Plug connector)
NAC3FX-W-TOP
(Connector)
NAC3MX-W-TOP
(Plug connector)
Power IN
APPLIANCE INLET APPLIANCE OUTLET APPLIANCE INLET / OUTLET
u Combination
Application:
· The powerCON TRUE1 system is certified as a connector with breaking capacity according IEC 60320-1.
® ®
· It is intended for use as an appliance coupler and interconnection coupler.
· It serves to supply power to an appliance and from an appliance to other equipment.
· To be installed by qualified person only.
powerCON TRUE1 TOP line is full backward compatible with the preceding powerCON TRUE1 products.
® ®
CONNECTOR ASSIGNMENT:
A APPLICATION INSTRUCTION
B ASSEMBLY INFORMATION
i
Power IN
APPLICATION & ASSEMBLY INSTRUCTION

20
250
P S
EJET
NAC3FX-W
NAC3FX-W
20
250
P S
EJET
-w
-w
ASSEMBLY INSTRUCTION powerCON TRUE1 TOP
I ® ®
R
G
2.
1.
Torque Value 0.7 Nm
Torx size
T8
5.
6.
E
F
Find more details of powerCON TRUE1 TOP on www.neutrik.com.
3.
Important:
Push and turn simultaneously.
CAUTION
To ensure protection category, do
not expose the connection to
bending forces (e.g. do not attach
loads to the cable, no free-dangling
cable windings etc.).
FORCE
SAFETY WARNING
For safety and certification reasons the connector must
be replaced in case of any broken parts or excessive
wear and tear.
2.
1.
Torque Value 2.0 Nm
PRESS FIRMLY
4.
Wrench size
13 mm
Slide the cable into the contacts and clamp with
the screw with Torx size T8.
Wiring VDE UL
L brown blackÞ
N blue whiteÞ
green / yellow greenÞ
Slide chuck onto insert (1) and then both into
housing (2).
Important: Align the chuck by positioning the
nose into keyway.
Slide the cable clamp (3) bushing up the cable
and tighten it with the tool (4) as shown (5).
Important: Black O-ring to hide to achieve IP
protection (6).
(Tool available: Art. No. HTAC)
NAC3FX-W
NAC3FX-W
www.neutrik.com
Draft. Nr.: BDA 541 V3
Update: 2023-02-22
Data subject to change without prior notice. 2023 NEUTRIK . NEUTRIK , powerCON are registered trademark of Neutrik AG.
® ®
©
ALL RIGHTS RESERVED.
Neutrik AG LI-9494 Schaan
I
Page 2
C FOR DISASSEMBLY
OPEN TWIST LOCK!
1. Press with screw driver to unlock
2. Turn bushing 360°.
3. Repat step 1 + 2 until bushing is unscrewed.
LIECHTENSTEIN
NAC3FX-W
20
250
P S
EJET
NAC3FX-W
D SAFETY INFORMATION
A brand of the Neutrik Group