New Air AH-410 User manual

OIL-FILLED
SPACE HEATER
Please read and save these instructions.
MODEL AH-410
Owner’s Manual
1
IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed in order to
reduce the risk of fire, electric shock, and injury. Carefully read all of the instructions below
before using this heater.
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surface. If
provided, always use handles when moving this heater. Keep combustible materials
such as furniture, pillows, bedding, papers, clothes and curtains at least 3’ (0.9 m) from the
front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and
whenever the heater is left operating and unattended.
4. Always unplug the heater when not in use.
5. Do not operate the heater with a damaged cord or plug, if the heater malfunctions, has been
dropped or damaged in any manner. Return heater to authorized service facility for
examination, electrical or mechanical adjustment, or repair.
6. Do not use the heater outdoors.
7. This heater is not intended for use in bathroom, laundry areas and similar moist indoor
locations. Never locate heater where it may fall into a bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar
items. Arrange cord away from high-traffic areas where it can be tripped over.
9. CAUTION: This appliance has a polarized plug (one blade is wider than the other).
To reduce the risk of shock,this plug is intended to fit only one way in a polarized
outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT attempt to alter this safety feature. Doing so
could result in an electric shock hazard.
10. This heater draws 12.5 A during operation. To prevent overloading a circuit, do not plug
the heater into a circuit that already has other appliances working.
11. CAUTION: It is normal for the plug to feel warm to the touch; however, a loose fit
between the AC outlet (receptacle) and plug may cause overheating and distortion
of the plug. Contact a qualified electrician to replace loose or worn outlet.
12. To disconnect the heater, first turn controls to the OFF position, then remove plug from
outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may
cause an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on
soft surface, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where
gasoline, paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons.
17. CAUTION: Avoid the use of an extension cord because the extension cord may
overheat and cause a risk of fire. However, if you have to use an extension cord,
the cord shall be No. 14 AWG minimum size and rated not less than 1875 W.
18. The output of this heater may vary and its temperature may become intense enough
to burn exposed skin. Use of this heater is not recommended for persons with reduced
sensitivity to heat or an inability to react to avoid burns.
SAVE THESE IMPORTANT INSTRUCTIONS
FOR REFERENCE.

2
DO NOT OPERATE THIS HEATER WITHOUT THE LEGSATTACHED
(See Fig. 1).
Fig. 1
Make sure the surface beneath the heater is clean and free from debris
or any obstructions. Placing this heater on high-pile carpeting or any
other surface that impedes the flow of air underneath the heater is not
recommended.
1.Connect the heater’s plug to a properly polarizedA/C 120V household
outlet in perfect working condition.
2.Press the power switch to “ ” (ON). Turn the thermostat knob clock
wise to the position.
3.When your room reaches the desired temperature, slowly turn the
thermostat knob counter-clockwise until you hear a clicking sound.
This will automatically set your heater to cycle on and off at your desired
heat setting. Please note that it will take approximately 15 minutes for
the heater to reach operating temperature.
4.To change the temperature, turn the thermostat knob clockwise to
increase the temperature or counter-clockwise to lower it.
5.To shut the unit off, press the power switch “ ” (OFF).
6.This heater is equipped with an overheat protection system that turns
the unit off if it overheats. At this time, the CAUTION light will also turn
on. If this occurs, turn the heater off and unplug it. Inspect the unit and
remove any objects on or adjacent to the heater. Allow the unit to cool
for a few minutes, plug it back in, and resume normal operation.
ASSEMBLY INSTRUCTIONS
OPERATING INSTRUCTIONS
CAUTION: To prevent electric shock, make sure the heater’s
plug is fully inserted into an appropriate outlet.
1.Before maintaining or cleaning the heater, always unplug it from the
outlet and allow it to fully cool. Wipe the heater clean with a soft, damp
cloth and do not use any detergents or abrasive cleaners.
2.If the heater will not be in use for an extended period of time, wind the
cord around the cord wrap and store the heater in a dry place.
3.This appliance has been built to ETL standards and specifications.
However, in case of malfunction, do not attempt to repair the heater by
yourself as this may result in fire or electric shock.
4.This heater is permanently sealed with oil. No oil changes are necessary.
5.This product is equipped with a polarized alternating current line (the plug
has one blade wider than the other). This is a safety feature. The plug
will fit into a power outlet only one way. If you are unable to fully insert the
plug into the outlet, try reversing the plug. If it still fails to fit into the outlet,
contact your electrician to have your outlet replaced. Do not tamper with
the plug or outlet as this will defeat the purpose of this safety mechanism.
Voltage: 120 V / 60 Hz
Model No.: AH-410
Power: 700 W
MAINTENANCE AND CLEANING INSTRUCTIONS
3