NI sbRIO-9697 User manual

sbRIO-9697
Getting Started
2022-07-06

Contents
Installation Purpose (RIO Mezzanine Card). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Kit Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Digital I/O Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the NI 9697. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3 V Digital I/O on 50-Pin IDC Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Physical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Environmental Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
EU and UK Customers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
电子信息产品污染控制管理办法（中国 RoHS）. . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Worldwide Support and Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ni.com
2
sbRIO-9697 Getting Started

Installation Purpose (RIO Mezzanine Card)
The NI 9697 two-slot C Series RIO Mezzanine Card is an accessory you can use to
connect up to two board-only C Series modules to the NI sbRIO-9607/9627.
sbRIO RMC Interface Connector
C Series
Module
C Series
Module
3.3 V
Digital I/O
5 V
Power Supply
x 24
Note NI recommends using the NI 9693 with the NI sbRIO-9605/9606 or
the NI sbRIO-9623/9626 as the NI 9697 is not compatible with these
products.
Note Board-only C Series modules are represented with an 'E' at the end
of the product name. For example, the NI 9219 is the enclosed C Series
module and the NI 9219E is the board-only version of the module.
Kit Contents
The NI 9697 kit contains the following components:
© National Instruments 3
sbRIO-9697 Getting Started

Figure 1. Contents of the NI 9697 Kit
4
3
2
1
6
5
1. M3 × 7 mm Silver Low-Profile Screw (x7)
2. M3 × 4 mm Black Low-Profile Screw (x10)
3. NI 9697
4. C Series Module Support Bracket (x3)
5. Isolator Sheet
6. M3 × 7 mm Stando (x6)
Caution NI makes no electromagnetic compatibility (EMC) or CE marking
compliance claims for the NI 9697. The end-product supplier is responsible
for conformity to any and all compliance requirements.
Caution The NI 9697 must be installed inside a suitable enclosure prior to
use. Hazardous voltages may be present.
ni.com
4
sbRIO-9697 Getting Started

Caution Follow proper ESD precautions to ensure you are grounded
before installing hardware.
Caution The protection provided by the NI 9697 can be impaired if the NI
9697 is used in a manner not described in this document.
Digital I/O Connector Pinouts
The following figure shows the pinouts of the I/O connector on the NI sbRIO device.
Figure 2. Pinout of the DIO Connector
J1, DIO
+5V
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
D GND
+5V
DIO22
DIO21
DIO19
DIO18
DIO17
DIO16
DIO23
DIO20
DIO15
DIO14
DIO13
DIO12
DIO11
DIO10
DIO9
DIO8
DIO7
DIO6
DIO5
DIO4
DIO3
DIO2
DIO1
DIO0
1 2
3 4
5 6
7 8
910
11 12
13 14
15 16
17 18
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
35 36
37 38
39 40
41 42
43 44
45 46
47 48
49 50
Pin 1
J1
Note The DIO numbering on this connector corresponds to naming of the
DIO on the NI sbRIO device. For example, DIO0 on the NI 9697 connector
corresponds to DIO0 on the NI sbRIO-9607/9627 RMC connector.
© National Instruments 5
sbRIO-9697 Getting Started

Installing the NI 9697
What to use:
■Socket driver, 4.5 mm
■Screwdriver, Phillips #1
Complete the following steps to install the NI 9697.
1. Attach the three C Series support brackets to the NI 9697 using six of the M3 ×
4 mm black, low-profile screws included in the kit.
Note Do not tighten the screws until you reach step 8. You may need
to adjust the brackets during assembly.
Figure 3. Attaching the Support Brackets to the NI 9697
2. Connect board-only C Series modules to the NI 9697.
Caution To avoid causing damage to the NI 9697 and the C Series
modules, do not allow C Series module support brackets to contact
ni.com
6
sbRIO-9697 Getting Started

components on the secondary side of the board-only C Series
modules.
Figure 4. Connecting Board-only C Series Modules to the NI 9697
3. Screw three of the remaining M3 × 4 mm black, low-profile screws into the
holes.
Figure 5. Inserting Three Screws into the Module and Bracket Holes
4. Insert the six M3 × 7 mm standos from the secondary side of the NI sbRIO
device into the six mounting standos for your application. The mounting
standos are not included in the NI 9697 kit.
Note You can attach the NI 9697 to an NI sbRIO-9607. You must
support the NI 9697 mounting holes that overhang the NI sbRIO
© National Instruments 7
sbRIO-9697 Getting Started

device with standos that are 9.2 mm (0.36 in.) taller than the
mounting standos described in step 4.
Figure 6. Inserting the Standos into the NI sbRIO Device
1
2
3
1. M3 × 7 mm Stando (x6)
2. sbRIO Device
3. Mounting Stando (x6, Not Provided)
5. Tighten the standos to 0.45 N · m (4.0 lb · in.). Do not overtighten.
6. Press the isolator sheet over the standos so that 1 mm to 2 mm of stando
protrudes through the holes.
7. Align the bracket holes attached to the NI 9697 with the tops of the M3 × 7 mm
standos, and insert the six M3 × 7 mm silver low-profile screws.
ni.com
8
sbRIO-9697 Getting Started

Figure 7. Inserting the Standos and Screws into the NI sbRIO Device
1
2
3
1. M3 × 7 mm Silver Low-Profile Screw (x6)
2. NI 9697
3. Isolator
8. Tighten all the screws to 0.45 N · m (4.0 lb · in.). Do not overtighten.
The following figures show the dimensions of the assembled NI 9697 and NI sbRIO
device with two board-only C Series modules.
© National Instruments 9
sbRIO-9697 Getting Started

Figure 8. Side View with Dimensions
71.70 mm
(2.820 in.)
13.40 mm
(0.530 in.)
9.20 mm
(0.360 in.)
Figure 9. Rear View with Dimensions
1
18.0 mm
(0.71 in.)
73.6 mm
(2.90 in.)
73.6 mm
(2.90 in.)
1. Recommended Keepaway from Modules
Tip For two-dimensional drawings and three-dimensional models of the
NI 9697, visit ni.com/dimensions and search by model number.
Specifications
Refer to the documentation for the NI sbRIO device and the board-only C Series
modules for the specifications of those products.
3.3 V Digital I/O on 50-Pin IDC Connector
Number of DIO channels 24
Maximum tested current per channel ±3 mA
Input logic levels
Input low voltage, VIL 0 V min; 0.8 V max
Input high voltage, VIH 2.0 V min; 5.25 V max
ni.com
10
sbRIO-9697 Getting Started

Output logic levels
Output high voltage, VOHwhen sourcing 3 mA 2.4 V min; 3.465 V max
Output low voltage, VOL when sinking 3 mA 0.0 V min; 0.4 V max
Physical Characteristics
If you need to clean the device, wipe it with a dry towel.
Torque for screws 0.45 N · m (4.0 lb · in)
Weight 82.8 g (2.92 oz)
Environmental
Operating temperature (IEC 60068-2-1, IEC 60068-2-2) -40 °C to 85 °C
Thermal validation of an NI sbRIO system assembled with the NI 9697 requires
validating the NI sbRIO device and board-only C Series modules. Measure the
operating temperature of board-only C Series modules 7.6 mm (0.3 in.) above the
module surface. Refer to the documentation of the NI sbRIO device and board-only
C Series modules for operating temperature limits and, if applicable, for typical
specifications.
Storage temperature (IEC 60068-2-1, IEC 60068-2-2) -40 °C to 85 °C
Operating humidity (IEC 60068-2-78) 10% RH to 90% RH, noncondensing
Storage humidity (IEC 60068-2-78) 5% RH to 95% RH, noncondensing
Maximum altitude 5,000 m
Indoor use only.
Environmental Management
NI is committed to designing and manufacturing products in an environmentally
responsible manner. NI recognizes that eliminating certain hazardous substances
from our products is beneficial to the environment and to NI customers.
© National Instruments 11
sbRIO-9697 Getting Started

For additional environmental information, refer to the Engineering a Healthy
Planet web page at ni.com/environment. This page contains the environmental
regulations and directives with which NI complies, as well as other environmental
information not included in this document.
EU and UK Customers
• Waste Electrical and Electronic Equipment (WEEE)—At the end of the product life
cycle, all NI products must be disposed of according to local laws and regulations.
For more information about how to recycle NI products in your region, visit ni.com/
environment/weee.
电子信息产品污染控制管理办法（中国 RoHS）
•
540
e
中国 RoHS— NI 符合中国电子信息产品中限制使用某些有害物质指令
(RoHS)。关于 NI 中国 RoHS 合规性信息，请登录 ni.com/environment/
rohs_china。(For information about China RoHS compliance, go to ni.com/
environment/rohs_china.)
Worldwide Support and Services
Visit ni.com/support to find support resources including documentation,
downloads, and troubleshooting and application development self-help such as
tutorials and examples.
Visit ni.com/services to learn about NI service oerings such as calibration options,
repair, and replacement.
Visit ni.com/register to register your NI product. Product registration facilitates
technical support and ensures that you receive important information updates from
NI.
NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX,
78759-3504, USA.
ni.com
12
sbRIO-9697 Getting Started
© 2022 National Instruments Corporation.