Nidec NE200 Series User manual

Serial No -3101A003
User Manual
NE200/NE300
High performance
vector control drive
Scan QR to follow us

Contents
Chapter 1 NE200/300 Product Introduction ........................................................................... 1
1.1 Model Description .......................................................................................................................................... 1
1.3 Product Series .................................................................................................................................................. 2
1.4 Specifications ................................................................................................................................................... 6
1.5 Product Outline, Mounting Dimension ........................................................................................................ 9
1.6 Operating eypad panel outline and mounting dimensions ..................................................................... 18
1.7 Keypad holder outline and mounting dimensions .................................................................................... 19
1.8 Bra ing resistor applying guide ................................................................................................................... 20
Chapter 2 Installation .................................................................................................................... 22
2.1 Environment .................................................................................................................................................. 22
2.2 Mounting Direction and Space .................................................................................................................... 23
2.3 Removal and mounting of eypad panel and enclosure .......................................................................... 23
Chapter 3 Wiring ............................................................................................................................ 25
3.1 Connection of the Product and Peripheral Devices ................................................................................... 25
3.2 Description of Peripheral Devices for Main Circuit .................................................................................. 26
3.3 Main Circuit Peripheral Devices Guide ..................................................................................................... 27
3.4 Terminal configuration of main circuit ....................................................................................................... 29
3.5 Attention for Main Circuit Wiring ............................................................................................................... 33
3.6 Control Terminal Wiring .............................................................................................................................. 37
3.7 Functions of Control Circuit Terminals ...................................................................................................... 39
3.8 Control board schematic drawing ............................................................................................................... 48
Chapter 4 Operation and isplay ............................................................................................. 51
4.1 Keypad ........................................................................................................................................................... 51

4.2 Function code viewing and modification ................................................................................................... 53
4.3 Display status of eypad ............................................................................................................................... 54
4.4 Password Setting ........................................................................................................................................... 55
Chapter 5 Parameters Brief ........................................................................................................ 56
Chapter 6 Parameter description .............................................................................................. 99
6.1 Group 0 Basic Function ............................................................................................................................... 99
6.2 Start and stop group (F1) ........................................................................................................................... 108
6.3 Auxiliary running function group (F2) ..................................................................................................... 114
6.4 Vector Control Parameters (F3) ................................................................................................................ 122
6.5 V/F Control Parameters (F4) .................................................................................................................... 130
6.6 Motor parameters group (F5) ................................................................................................................... 135
6.7 Input terminals group (F6) ........................................................................................................................ 138
6.8 Output terminals group (F7) ..................................................................................................................... 150
6.9 PID Parameters (F8) .................................................................................................................................. 159
6.10 PLC and Multi-steps group (F9) ............................................................................................................ 166
6.11 Wobble frequency running group (FA) ................................................................................................. 171
6.12 Fixed-length control group (Fb) ............................................................................................................. 172
6.13 Protection and fault parameters group (FC) .......................................................................................... 173
6.14 Communication parameters group (Fd) ................................................................................................ 177
6.15 Operation interface & display group (FE) ............................................................................................ 180
6.16 Running history record group (FF) ........................................................................................................ 182
6.17 Protection Parameters (FP) ..................................................................................................................... 184
Chapter 7 Fault information and trouble shooting ...........................................................187
7.1 Fault information and solutions. ............................................................................................................... 187
7.2 Warning information .................................................................................................................................. 192
7.3 The general fault diagnosis and solutions ................................................................................................ 192

Chapter 8 Routine Repair and Maintenance ......................................................................194
8.1 Routine Maintenance ................................................................................................................................. 194
8.2 Periodic Maintenance ................................................................................................................................ 196
8.3 Component Replacement ......................................................................................................................... 196
8.4 Warranty ...................................................................................................................................................... 197
Appendix A NE300 Closed-loop Control ..............................................................................198
Parameter Brief ................................................................................................................................................. 198
Fault code of encoder ....................................................................................................................................... 203
Appendix B: Modbus Communication Protocol ................................................................204
Appendix C: Adapted encoder instruction ...........................................................................214
Appendix NE300 advanced control PCBA（Option） ..............................................215
NE300 advanced control PCBA diagram ................................................................................................ 215
Wiring of control circuit ............................................................................................................................... 216
CAN non-standard protocol instruction ........................................................................................................ 218
Appendix C: NE300 Option cards instruction ....................................................................220
Function brief of option cards ......................................................................................................................... 220
Mounting instruction of option card (PCBA) ............................................................................................... 222
Resolver PG encoder option instruction ........................................................................................................ 225
5V differential signal PG encoder option ....................................................................................................... 227
24V differential signal PG encoder option .................................................................................................... 231

Revision History
Date Version Description
2020/4/2 1.0 Issued for the first time
2020/5/19 1.1 Add “Modbus Address column in parameter brief list

Safety Information
Description of safety marks:
Warning: A Warning contains information which is essential for avoiding a
safety hazard.
Caution: A Caution contains information which is necessary for avoiding a
risk of damage to the product or other equipment.
 Use
Warning
 This series of drive is used to control the variable speed operation of
three-phase motor and cannot be used for single-phase motor or
other applications. Otherwise, drive failure or fire may be caused.
 This series of drive cannot be simply used in the applications directly
related to the human safety, such as medical equipment.
 This series of drive is produced under strict quality management
system. Redundancy or bypass solution is necessary if the drive
failure may cause severe accident or loss.
 Installation
Caution
 If the drive is found to be damaged or parts missing, the drive cannot
be installed. Otherwise, accident may be caused.
 When handling and installing the product, please hold the product
from bottom. Do not hold the enclosure only. Otherwise, your feet
may be injured and the drive may be damaged because of dropping.
 The drive shall be mounted on the fire retardant surface, such as
metal, and kept far away from the inflammables and heat source.
 Keep the drilling scraps from falling into the inside of the drive during
the installation; otherwise, drive failure may be caused.
 When the drive is installed inside the cabinet, the electricity control

cabinet shall be equipped with fan and ventilation port. And ducts for
radiation shall be constructed in the cabinet.
 Wiring
Warning
 The wiring must be conducted by qualified electricians. Otherwise,
there exists the risk of electric shock or drive damage.
 Before wiring, confirm that the power supply is disconnected.
Otherwise, there exists the risk of electric shock or fire.
 The grounding terminal PE must be reliably grounded, otherwise, the
drive enclosure may become conductive.
 To ensure the safety, the drive and the motor must be grounded.
Please do not touch the main circuit terminal. The wires of the drive
main circuit terminals must not contact the enclosure. Otherwise,
there exists the risk of electric shock.
 The connecting terminals for the braking resistor are （+）and PB.
Please do not connect terminals other than these two. Otherwise, fire
may be caused.
Caution
 The power supply cannot connect to output terminals U-V-W,
otherwise, the drive will be damaged.
 It is forbidden to connect the output terminal of the drive to the
capacitor or LC/RC noise filter with phase lead, otherwise, the internal
components of the drive may be damaged
 Please confirm that the power supply phases, rated voltage are
consistent with that of the nameplate, otherwise, the drive may be
damaged.
 The wires of the main circuit terminals and the wires of the control
circuit terminals shall be laid separately or in a square-crossing mode,
otherwise, the control signal may be interfered.
 When the length of the cables between the drive and the motor is
more than 100m, it is suggested to use output reactor to avoid the

 Operation
Warning
 Power supply can only be connected after the wiring is completed
and the cover is installed. It is forbidden to remove the cover in live
condition; otherwise, there exists the risk of electric shock.
 When auto failure reset function or restart function is set, isolation
measures shall be taken for the mechanical equipment, otherwise,
personal injury may be caused.
 When the drive is powered on, even when it is in the stop state, the
terminals of the drive are still live. Do not touch the drive terminals;
otherwise electric shock may be caused.
 The failure and alarm signal can only be reset after the running
command has been cut off. Otherwise, personal injury may be
caused.
Caution
 Do not start or shut down the drive by switching on or off the power
supply, otherwise the drive may be damaged.
 Before operation, please confirm if the motor and equipment are in
the allowable use range, otherwise, the equipment may be damaged.
 The heat sink and the braking resistor have high temperature. Please
do not touch such devices; otherwise, you may be burnt.
 When it is used on lifting equipment, mechanical contracting brake
shall also be equipped.
 Please do not change the drive parameter randomly. Most of the
factory set parameters of the drive can meet the operating
requirement, and the user only needs to set some necessary
parameters. Any random change of the parameter may cause the
damage of the mechanical equipment.
drive failure caused by the over-current of the distribution capacitor.
 The drive which equipped with DC reactor must connect with DC
reactor between the terminal of P1、(+) otherwise the drive will not
display after power on.

 In the applications with mains frequency and variable frequency
switching, the two contactors for controlling the mains frequency and
variable frequency switching shall be interlocked.
 Maintenance & Inspection
Warning
 In the power-on state, please do not touch the drive terminals;
otherwise, there exists the risk of electric shock.
 If cover is to be removed, the power supply must be disconnected
first.
 Wait for at least 10 minutes after power failure or confirm that the
CHARGE indicator is off before maintenance and inspection to
prevent the harm caused by the residual voltage of the main circuit
electrolytic capacitor to persons.
 The components shall be maintained, inspected or replaced by
qualified electricians.
Caution
 The circuit boards have large scale CMOS IC. Please do not touch
the board to avoid the circuit board damage caused by static
electricity.

NE200/300 Series rive User Manual
Chapter 1 Introduction to NE200/300 Series rive 1
C apter 1 NE200/300 Product Introduction
1.1 Model Description
The digits and letters of the drive model number on the nameplate
indicate information such as the product series, power supply class, power
ratings and software/hardware versions.
Fig.1-1 Product Model Description
Note：NE300-4T0300G/0370P means this model can be used as 30kW
heavy duty and 37kW normal duty.
1.2 Product Nameplate Description
Fig.1-2 Nameplate
NE 4T0022GB-M
Product SeriesNE200NE300Voltage Rating2S:200~240V4T:380~440VPower Rating0004(0.4kW)0007(0.75kW)0015(1.5kW)~1320(132kW)~9000(900kW)Structure CodeNoneStandard--MCompact--UUp in down out--DDown in down out--FFreestandingBrakeUnitNoneNobrakeunitBWithbrakeunitApplication TypeGHeavy DutyPNormalDuty

NE200/300 Series rive User Manual
2 Chapter 1 Introduction to NE200/300 Series rive
1.3 Product Series
1.3.1 NE200 Product Series
 NE200−4T □□□□ GB Three-phase 400V Constant torque/heavy-duty
application
Power（kW） 0.75 1.5 2.2 4.0
Adapted motor (kW) 0.75 1.5 2.2 4.0
Output
Voltage (V) 3phase 0~rated input voltage
Rated current (A) 2.5 4.0 6.0 9.0
Overload 150% 1min; 180% 20sec.
Input
Rated Volt/ Freq 3phase 380V/440V; 50Hz/60Hz
Voltage range 304V~456V; voltage imbalance ≤3%; Allowable
frequency fluctuation ±5%
Rated current (A) 3.7 5.4 7.0 10.7
Braking unit Standard (Built-in)
IP rating IP20
Cooling Forced air cooling
 NE200−4T□□□□PB Three-phase 400V Squared torque/normal-duty
application
Power（kW） 1.5 2.2 4.0 5.5
Adapted motor (kW) 1.5 2.2 4.0 5.5
Output
Voltage (V) 3phase 0~rated input voltage
Rated current (A) 4.0 6.0 9.0 13
Overload 120% 1min; 150% 1sec.
Input
Rated Volt/ Freq 3phase 380V/440V; 50Hz/60Hz
Voltage range 304V~456V; voltage imbalance ≤3%; Allowable
frequency fluctuation ±5%
Rated current (A) 5.4 7.0 10.7 15.5
Braking unit Standard (Built-in)
IP rating IP20
Cooling Forced air cooling

NE200/300 Series rive User Manual
Chapter 1 Introduction to NE200/300 Series rive 3
 NE200−2S□□□□GB Single-phase 220V constant torque/heavy duty
application
Power（kW）
0.4
0.75
1.5
2.2
Adapted motor (kW)
0.4
0.75
1.5
2.2
Output
Voltage (V) Single phase 0~rated input voltage
Rated current(A) 2.5 4.5 7.0 10
Overload 150% 1min; 180% 20sec.
Input
Rated Volt/Freq 1phase 200V/240V; 50Hz/60Hz
Voltage range 176V~264V; voltage imbalance ≤3%; Allowable
frequency fluctuation ±5%
Rated current (A) 5.3 8.3 14 23
Braking unit Standard (Built-in)
IP rating IP20
Cooling Forced air cooling

NE200/300 Series rive User Manual
4 Chapter 1 Introduction to NE200/300 Series rive
1.3.2 NE300 Product Series
 NE300−4T□□□□GB Three-phase 400V Constant torque/heavy-duty
application
Power
（
kW
）
1.5
2.2
4.0
5.5
7.5
11
15
18.5
22
30
37
45
55
75
90
110
Adapted Motor
（kW） 1.5 2.2 4.0 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110
Output
Voltage
（V）3Phase 0~Rated input voltage
Rated
Current(A)
4 6 9 13 17 25 32 37 45 60 75 90 110 150 176 210
Overload
150%
1
min;
180%
20
sec
Input
Rated
Volt/Freq
3Phase 380V/440V; 50Hz/60Hz
Voltage
Range
304V～456V
voltage imbalance ≤3%
Allowable frequency fluctuation ±5%
Rated
Current（A）
5.4 7.0 10.7 15 20.5 27 35 38.5 46.5 62 76 92 113 157 180 214
Brake Unit
Built
-
in
Built
-
out
IP Rating
IP20
Cooling
Forced air cooling
Power（kW） 132 160 185 200 220 250 280 315 355 400 450 500 560 630 710 800
Adapted Motor
（kW）
132
160
185
200
220
250
280
315
355
400
450
500
560
630
710
800
Output
Voltage
（V）3Phase 0~Rated input voltage
Rated
Current(A)
250 300 340 380 420 470 540 600 660 730 840 900 950 1160 1300 1460
Overload
150% 1min; 180% 20sec
Input
Rated
Volt/Freq
3Phase 380V/440V; 50Hz/60Hz
Voltage
Range 3Phase 380V/440V; 50Hz/60Hz 150% 1min;180% 20sec
Rated
Current（A）
256 307* 345 385* 430* 480* 548* 610* 670* 740* 850* 910* 960* 1170* 1310* 1470*
Brake Unit
Built
-
out
IP Rating
IP20
Cooling
Forced air
cooling
* NE300−4T1600G-F and above products are equipped with in-built DC reactor as standard.

NE200/300 Series rive User Manual
Chapter 1 Introduction to NE200/300 Series rive 5
 NE300−4T□□□□PB Three-phase 400V Squared torque/normal-duty
application
Power（kW） 2.2 4.0 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132
Adapted Motor（kW） 2.2 4.0 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132
Output
Voltage
（V
）
3Phase 0~Rated input voltage
Rated
Current（A
）
6.0 9.0 13 17 25 32 37 45 60 75 90 110 150 176 210 250
Overload
120% 1
min;
150% 1
sec
Input
Rated
Volt/Freq
3Phase 380V/440V; 50Hz/60Hz
Voltage
Range
304V
～
456V
Voltage imbalance ≤3%
Allowable frequency fluctuation ±5%
Rated
Current（A
）
7.0 10.7 15.5 20.5 26 35 38.5 46.5 62 76 92 113 157 180 214 256
Brake Unit
Built
-
in
Built
-
out
IP Rating
IP20
Cooling
Forced air cooling
Power（kW） 160 185 200 220 250 280 315 355 400 450 500 560 630 710 800 900
Adapted Motor（kW）
160
185
200
220
250
280
315
355
400
450
500
560
630
710
800
900
Output
Voltage
（V
）
3Phase 0~Rated input voltage
Rated
Current（A
）
300 340
380 420 470 540 600 660 730 840 900 950
116
0
130
0
146
0
164
0
Overload
120% 1min; 150% 1sec
Input
Rated
Volt/Freq
3Phase 380V/440V; 50Hz/60Hz
Voltage
Range
304V
～
456V
Voltage imbalance ≤3%
Allowable frequency fluctuation ±5%
Rated
Current（A
）
307
345
385* 430* 480* 548* 610* 670* 740* 850* 910* 960* 1170* 1310* 1470* 1650*
Brake Unit
Built
-
out
IP Rating
IP20
Cooling
Forced air cooling
* NE300−4T1850P and above products are equipped with external DC reactor as standard.

NE200/300 Series rive User Manual
6 Chapter 1 Introduction to NE200/300 Series rive
1.4 Specifications
NE200
NE300
Control
features
Control mode Closed-loop
vector (VC)
Open-loop
vector (SVC)
V/F
control
Closed-loop
vector (VC)
Open-loop
vector (SVC)
V/F control
Startup torque ---- 0.5Hz
150%
1.5Hz
150%
0.00Hz
180%
0.5Hz
150%
1.5Hz
150%
Speed adjust range ---- 1:100 1:50 1:1000 1:100 1:50
Speed stabilization
precision ---- ± 0.2% ± 0.5% ± 0.02% ± 0.2% ± 0.5%
Torque control ---- Y N Y Y N
Torque precision ---- ± 10% ---- ± 5% ± 10% ----
Torque response time ---- <20ms ---- <10ms <20ms ----
Key Function
Length control; Drooping control
S curve Acc./Dec;
Autotuning; Torque tracking
Switching Torque/ Speed control mode; Multi-function I/O terminals
Undervoltage adjustment; Torque limit; Multi-steps operation
Flying start, Slip compensation; Rich PID; Simple PLC (On board)
Manual/auto torque boost; Current limitation; AVR Function;
AC operation grounding switching
Freq. setting mode Terminal pulse input (X4, X5)
Keypad, terminal up/down, communication (host), analog input AI1 AI2
Output Freq. 0.0~550.0Hz
Starting frequency 0.0~60.00Hz
Acc./Dec. time 0.01~3600s 0.1~3600s
Dynamic braking 400V Braking unit action voltage 650~750V
200V Braking unit action voltage 360~390V

NE200/300 Series rive User Manual
Chapter 1 Introduction to NE200/300 Series rive 7
DC braking
DC braking activation frequency:0.00~550.0Hz;
DC braking current: G type 0.0~100.0%; P type 0.0~80.0%
DC braking time:0.0~30.0s; Quick DC brake activation without lag time
Magnetic flux braking Decelerating quickly by adding motor magnetic flux
Unique
functions
Multi-function key
(MFK)
MFK can exchange operations quickly. Such as JOG, FWD/REV switch, Running
command reference modes etc.
Parameter copy Parameter upload & download via keypad
User can forbid the overwriting of the uploaded parameters.
Common DC bus ---- Yes
Independent air duct ---- Yes
Option card ----
Various Option cards including I/O
Expansion card, injection molding interface
card, ±10V analog Option card, etc.
Power-on detection ---- Automatic detection of internal and
peripheral circuits while power-on
Communicat
ion
Rs485 protocol Equipped with Modbus-RTU communication protocol
Protections
Protections for: Phase-to-phase short circuit,
Auto-tune failure, Output-to-ground short circuit,
Parameter copy error, Option card connection error,
Communication error, Power supply abnormal,
IGBT protection Temperature sampling abnormal,
Output phase lost, Power supply under/over-voltage,
External devices faults, Analog input/output abnormal, Temperature sampling offline
Drives/motor overload Abnormal power failure in running
Over-current, Under/over voltage, Relay contact error
Encoder off-line, Heat sink over-heat, EEPROM abnormal

NE200/300 Series rive User Manual
8 Chapter 1 Introduction to NE200/300 Series rive
Efficiency
Used as rated power: 7.5kW and below
ratings ≥93%, 11kW~45kW ratings ≥95%,
55kW and above ratings ≥98%
Environment
Application Environment In-door, free from sunshining directly, dust, corrosive gas,
combustible gas, oil mist, steam, water drop or salt
Ambient temperature -10 ~ +40ºC, derated at 40 ~ 50ºC, the rated output current shall be
decreased by 1% for every temperature rise of 1ºC
Humidity 5~95%,no condensing
Vibration 3.5mm, 2~9Hz; 10 m/s
2
, 9~200Hz; 15 m/s
2
, 200~500Hz
Altitude 0~2000m; Derating use above 1000m; Derate 1% every 100m
higher.
Storage temperature −40~ +70ºC

NE200/300 Series rive User Manual
Chapter 1 Introduction to NE200/300 Series rive 9
1.5 Product Outline, Mounting Dimension
（Unit：mm）
Note: NE200 series support 35mm DIN-rail mounting.
Model Dimensions
NE200-2S0004GB
See Fig. A
NE200-2S0007GB
NE200-2S0015GB
NE200-4T0007G/0015PB
NE200-4T0015G/0022PB
NE200-4T0022GB-M
NE200-2S0022GB
See Fig. B
NE200-4T0022G/0040PB
NE200-4T0040G/0055PB
NE200-2S0004GB
Note
-M means mini model
Fig. A

NE200/300 Series rive User Manual
10 Chapter 1 Introduction to NE200/300 Series rive
Fig. B
Model Dimensions
NE300-4T0015G/0022PB
NE300-4T0022G/0040PB
NE300-4T0040G/0055PB
See Fig. C
NE300-4T0055G/0075PB
NE300-4T0075G/0110PB
NE300-4T0110G/0150PB
See Fig. D
NE300-4T0150G/0185PB
NE300-4T0185G/0220PB
NE300-4T0220G/0300PB
See Fig. E
NE300-4T0300G/0370P
NE300-4T0370G/0450P
See Fig. F
NE300-4T0450G/0550P
NE300-4T0550G/0750P
See Fig. G
NE300-4T0750G/0900P
NE300-4T0900G/1100P
NE300-4T1100G/1320P
See Fig. H

NE200/300 Series rive User Manual
Chapter 1 Introduction to NE200/300 Series rive 11
Model Dimensions
NE300-4T1320G/1600P-U
NE300-4T1320G/1600P-D
NE300-4T1600G/1850P-U
NE300-4T1600G/1850P-D
See Fig. I
NE300-4T1850G/2000P-U
NE300-4T1850G/2000P-D
NE300-4T2000G/2200P-U
NE300-4T2000G/2200P-D
NE300-4T2200G/2500P-U
NE300-4T2200G/2500P-D
NE300-4T2500G/2800P-U
NE300-4T2500G/2800P-D
See Fig. J
NE300-4T1600G/1850P-F
NE300-4T1850G/2000P-F
NE300-4T2000G/2200P-F
NE300-4T2200G/2500P-F
See Fig. K
NE300-4T2500G/2800P-F
NE300-4T2800G/3150P-F
NE300-4T3150G/3550P-F
See Fig. L
NE300-4T3550G/4000P-F
NE300-4T4000G/4500P-F
NE300-4T4500G/5000P-F
NE300-4T5000G/5600P-F
See Fig. M
NE300-4T5600G/6300P-F
NE300-4T6300G/7100P-F
NE300-4T7100G/8000P-F
NE300-4T8000G/9000P-F
See Fig. N
NE300-4T9000G-F See Fig. P
Note:
-U means input lines come from upside and output lines come out
downside.
-D means input lines come from downside and output lines come out
downside.
-F means freestanding models