Nidec TNX Series User manual

DIGTAL TORQUE METER
Please read the following content before operation
Please read instruction manual and [safty notes]carefully before
operation,the operate correctly.
93591B
Instruction Manual
TNX SERIES
www.nidec-shimpo.co.jp

1
Safty notes
Please read instruction manual carefully before installation ,operation,maintenance,check,read
,product knowledge,safty information,not before operation.
[Danger],[warning],[cantion]differentiate the importance of safty notes in the instruction
manual,they are very import.Please comply.
please comply
Danger mark indicates o possible death,serious injury or 󲶻re if the user
disregards the instruction .
Danger
Warning mark indicates the possibility of a serious injury if the user does not
follow the instruction .
Caution mark indicates the possibility of light injury or dangers if user operates
improperly .And that lead to great effect base on different instance.please comply.
Darning
cantion
Warning
Cauction
The following marks indicate the sort of contents which are complied voith.
The mark indicates warning,please pay attention .
The mark indicates prohibit operation.
The mark indicates follow instraction.
Heavy! Pay close attention to operation
When the product falls on user foot ,it leads to serious injury .
※ Please refer to P25 about the weight of product.
Please place the product on the
convenient .
cocation when mainterance and
check.
Please check it the object is 󳞛x up.
Please check the object is 󳞛x up not to more.
The object cannot be test correctly while ti can move.
Do not mangle ,bend ,oull , turn,truss power
cables.Don't place object on the cables
.Don't nip power cables.
while power cable breakoff,it may lead to
electric shock,󳞛re,injury.
While exceeded the bound of toquemoment
Don't exceed the bound of
torquemoment.
,the inductor and other parts may go wrong .
Do not more and hold the product
while .
The power is on while power cables break
off,it may lead to electric shock,󳞛re,injury.
Please check the electric source is single
phase .
The voltage of electrical outlet is equalto the mark
voltage.Don't connects many power cables.
while power cable break off,it may lead to electtic
shock ,󳞛re,injury.

2
Cauction
Don't charge with other instuction except
AC connect instrution ,it may leads to circuit
damage and 󳞛re.
Please insert power cable. into AC connet
instrument while use in the loose condition,it
may lead to electric shock and 󳞛re for short
circuit.
Don't disconnect .repair ,alter.
It may lead to injury for improperty operation.
Don't use except AC 100v
It may lead to 󳞛re and electrical shock 󳞛re .
Don't plug into or unplug from AC connect
instrument.
it may leads to electric shock.
Don't haul AC connect instrument .
If soft cable break off,it may lead to
󳞛re,forshort circuit.
Don't use while AC connect instrument touch
with dust it may lead to 󳞛re.
Please wipe with the clean .Soft cloth while it
is dirty.Don't use gas ,thinner,ethanet.
Suggest examination and adjustment at times.
The test de󳞛nition will drop together with time
according to the use frequency and torque.
Don't use and save in the following
enviroment:dank, sunniness,corrsive
air,󳞜ammable air.
・ The environmental which requires water, the place where direct sunlights hit
・ Environment which condensation generates
・ Environment with much dust, salt, and iron
・ Environmental which requires oil, water, and chemicals
・ A place with corrosive gas and combustible gas
Use it the temperature bound(0 ～ 40℃ )
It may lead to wrong operation if exceed the
temperature bound.
Use in the humidity bound(35 ～ 85%RH)
(Not mirage).It may lead to wrong operation if
exceed the humidity.
INDEX
13.2 Characteristic of digitorq_TNX 20
13.3 loandown sequence of digitorq_TNX 20
13.4 notes in USB operation 20
14. Convient function 21
14.1 Set the loading of storage outside 21
14.2 Warning code in setting parameter 21
15. set the operation of time 22
16. Connect instrument outside 23
16.1 Pin eith lock 23
16.2 Overload output/compare instrum output 23
17. Charge 24
18. Technolgy supporting 24
18.1 About repairment and rectfy 24
18.2 Guarantce 24
19. Type 25
20. Rule grap 25
8. Graduat function 8
8.1. Record graduation 8
8.2. Express graduation 9
8.3. Canel graduation 11
8.4. Canel all data 11
9． Save USB graduation(all graduat data) 12
9.1 Method for saving USB graduation 12
9.2 Warning code in USB graduation saving 12
9.3 Format of data 󳞛le 13
1
0． Copy output 14
10.1 Method for copying statist data 14
10.2 Example and format of print 14
11. Set function 15
11.1 Types of function 15
11.2 Method of operation 15
12． Set daterminant upper 18
12.1 Set operating of determiant upper 18
12.2 Output of determinant result of
compare instrument 19
13. The adoption of data 20
13.1 Function of USB communication 20
1. Characteristic of this product 3
2. Con󳞛rm the appendant 3
3. Name and function of each part 3
3.1. Mainframe 3
3.2. Operational panel 4
3.3. LCD display part 4
3.3.1. Value display part 4
3.3.2. Unit display part 5
3.3.3. Charge display part 5
4. Summary of keyboard 5
4.1. Basal key operation 5
4.2. Pecial key operation 5
5. Method of tes 5
5.1. Method of open test
6
5.2. Method of close test 6
5.3. Method of average test
6
6. Function of compare instrument 7
7. Method of test 7
7.1. Fixing of test sample 7
7.2. 0 point adjustment 7
7.3. Determine 7

3
1.Characteristic of this product
● Because it suit for P.P,so you can land save function 1st ,2nd ,3rd ,close,each of which are 1000 details.
● Can test the torque of open.close direction.
● Can save graduate land value to USB storge.
● Because of USB communication, it can send data into computer .
● Connect to the printer(buy besides),you can print save data.
● Can shift overload output/compare instrum output
● Because it is suitable for spare electric.
● Tsrque(DSP_10),you can use it as electric tsrque test.
● Record data,time of open/close Max value recorded through clock funtion.
● Can test MAX value
● Prove 󳞛 x torque of instruction 2N.m,5N.m,10N.m.
● Can shift each unit of N.m,N.m.
● Can chose test cycle(inclicate cycle)from 8t/s,4t/s,2t/s,1t/s.
2.Confirm the accessory
ainframe backside of mainframe
2. AC connect instrument
6. Instruction manual
3. fix bolt(4)
（30mm lengths）
4. USB voire 5. USB storge
3.Name and funtion of each part
3.1 Mainframe
Operation panel
Fix bolt
Fix open handle
AC connect instrument
Special socket for USB storge
Test table
Use to connect with soket forUSB communication
AC connect instrument
Test table put test sample
Operation panel 各種キー、 LED が配置されています。
Special socket for USB storge USB メモリを差し込みます。 ( 注 ) PC との通信には使用できません。
Fix open handle チャックピンを開閉させる際に使用します。
Fix bolt サンプルを固定する際に使用します。
Socket for AC connect instrument AC アダプタで動作させる際に使用します。
Connect socket outside Use when connect spare electric torque or print(use when exceed output/compare instrument output)
Socket for USB communication Use when PC is communicating with USB.
1.ainframe

4
3.2 Operation panel
① POWER KEY Use for ON/OFF the power
② RECALL KEY Load the data inputed in storge when open/close the test.
Can't load the data inputed in storge shen in overage testing.
③ MEM KEY Input max value into storge when open/close the test .Can't save input when in average testing.
④ Open/Close KEY Shift test method
Keep pressing the button will return to the method.
⑤ FILE KEY When it is open/close test method :save store data of mainframe into USB storge
Store data indicates:input store data of mainframe to printer . （(only when F06=print
⑥ ZERO/RST KEY When avweage test: set zero.Method of open/close test : resert max value
⑦Lcd indicate part Indicate test data or test unit .
⑧Test indicate LED One of open ,Mean,Close light, then indicate test method.
⑨Compare test determination
indicate LED When campare test determination is effective ,one of Hi,Go,Lo is light then indicates determinant recult.
Method of average test: against test data to do determinant of compare test and indicate result.
Method of open/close test :against max value to do determinant of compare test and indicates result.
When store exprossing ,against store value to do determinant of compare test and indicate result.
Hi,Go,Lo isn't light when determinant of compare test doesn't work.
② RECALL KEY
⑦ Lcd indicate part
① POWER KEY
⑧ Test indicate LED
⑨ Compare test determination indicate LED
④ Open/CloseKEY
③ MEM KEY
⑤ FILE KEY
⑥ ZERO/RST KEY
3.3 LCD indicate part
3.3.1 Value indicate part
Indicat the test value with symbol and 4 states value.
The symbols of torque are different according to the difference of test method .
Charging display
Numbers displays (measurement values the display)
Units display
LO BAT
Test method Torque of open direction Torque of close direction
Open test method No symbol Indicate negative
Close test method Indicate No symbol
Average test method No symbol Indicate negative

5
4.Summary of key operation.
4.1 Operation of basic operation.
3.3.3 Charging display
Indicate 󳞜lowing contents accrding to charge state.
LO BAT Blinking ：
The internal nickel metal hydride batteries
voltages is declinning.
Please connect AC suitable instrument to
charge.
BAT At display:
A internal nickel metal hydride batteries is
under charge.
Even shut off the power,indicates "BAT"
when charging.
Names of keys Operation
POWER ON/OFF of power
Open/Close Transfer test method
FILE Save data into USB panel/printer
ZERO/RST Set resert 0 /resert MAX height
MEM Input data of MAXheight
RECALL Indicate after record data
4.2 A special key the operation
Operation key Operation Operation method
ZERO/RST ＋ POWER Function form When power is OFF,keep pressing ZERO/RST and power,then away.
MEM ＋ POWER Cancel store data When power is OFF,keep pressing MEM and until indicate"non E"canceled by store data.
RECALL ＋ POWER Comparison set When power is OFF,keep pressing recall key and power the away.
Keep pressing RECALL until indicates"1-H"of comparison set.
FILE ＋ POWER Time set When power is OFF ,keep pressing FILE and power then away.
Keep pressing FILE until indicates"YEA"of time set.
3.3.2 Express unit
Express unit . Indicate"OVR"when exceed load Indicat"PWR"one minute before turn off the power .
Blinking the LED of Open,Mean,Close
N・m Unit N・cm Unit At the overload Auto power off before 1 minute
5.Test form
Test form contains open test porm,close test form,use open/close button to shift.
Open Mean Close Open Mean Close Open Mean Close
Open test porm Average test method Close test form
Open
Close Open Close
Open
Close
Nm Nm Nm

6
5.3Average test form
Indicate torque walue each sample(1000t/s)of test table direction according cycle with real time torque.
cycle setted accroding to mochine funtion, add number "1"to torque of close direction(1t/s,2t/s,4t/s,8t/s)
resert 0 by press ZERO/RST key.
Open Mean Close Open Mean Close
Zero- point adjustments
Open Mean Close Open Mean Close
Peak reset
5.1 Open test form
Test the max torque presured on test table of open direction.
Display cycle ： 8 times per second.
Resert max height point by press ZERO/RST key.
resert max height point.
torque indicates
torque indicates
When correlative with close direction indicate with out of wine of real time
When correlative with open direction indicate with out of wire of real time
real torque
real torque
The opening directions
The closing directions
＋
＋
－
－
ZERO
RST
ZERO
RST
5.2 Close test form
Test the max of torque pressed on close diection of test table.
Display cycle ： 8 times per second.
Resert the max height point by press ZERO/RST.
Set 󳞛lter(F04)as 150 mesc,then 150t/s.
※
※
Use"-"express torque value if close driection . use out of wine of real time to
express torque of max height point pressed on open direction.
Use"-"express torque value of open direction. use out of wire of real time to
express torque of max height point pressed on close direction.
Nm Nm
Nm
OpenOpen MeanMean CloseClose
Nm Nm
ZERO
RST
ZERO
RST
ZERO
RST
Nm
The opening directions
The closing directions

7
● average average test method
determinate HI when test data is in -101 (LED of "HI" light)
determinate GO when test data is in -100-50 (LED of "GO" light)
determinate LO when test data is in -49-49 (LED of "LO" light)
determinate GO when test data is in 50-100 (LED of "GO" light)
determinate HI when test data is in 101- (LED of "HI" light)
7.Measuring method
7.1 Fix test smaple
1 relax handle for set on off one test table
2 adjust the set bolt to compatible bulk and shape,then insert into any position.
3 put sample on the test table
4 close handle of set on_off and fasten the sample
※ fasten the main top of sample to the center of the table
When it is difficult for a form to bring an end caps to centers of tables with bad samples etc., please manufacture the fixture implement
reserving a
sample.
※ The length of a zipper pin is preparing 10mm, 20mm, and 50mm as the option.
7.2 ZERO adjustment
Turn test sample toward testing direction,it will appear torque about sample.
So you have to keep pressing ZERO/RST key to resert before test next sample.
7.3 Please resert peak in cordition of no connection with torque.
If a measuring samples is turned in direction, the torque concerning a sample will be displayed.
Since display maintenance of the maximum of the torque which started is carried out, in the case of opened and closed torque measurement mode, please
press the ZERO/RST keys, and carry out peak reset, before measuring the following samples.
※ Please perform peaks resets in the state where torque does not start.
6.Function of test instrument
■ Determinant management(determinant upper limit value:100/determinant lower limit value 50)
● when open test method
determinate LO when test data is in 0-49 (LED of "LO" light)
determinate GO when test data is in 50-100 (LED of "GO" light)
determinate HI when test data is in 101- (LED of "HI" light)
open
close
100
50
0
Hi：Lighting
Go：Lighting
Lo：Lighting
Upper value
Lower value
Not the results
● when close test method
determinate LO when test data is in 0-49 (LED of "LO" light)
determinate GO when test data is in 50-100 (LED of "GO" light)
determinate HI when test data is in 101- (LED of "HI" light)
100
50
0
Lo：Lighting
Go：Lighting
Upper value
Lower value
Hi ： Lighting
Not the results
open
close
(-100)100
(-50)50
0
Lo：Lighting
Go：Lighting
Lower value
Hi ： Lighting
open
close
100
50
Go：Lighting
Upper value
Hi ： Lighting
Lower value
Upper value
Ｈｉ Ｇｏ Ｌｏ
Measurement table
Zipper pin
Cap
Chuck opening knobs
Sample-and-hold jigs
※ It is an end caps to the center
of a jigs implement.
Wrong installation Correct installation
×○
( )In the inside, it is a display value.
・ Compare determinant upper/lower limit value with test data,max or store data loaded.LED light and indicate result.
・ Can set determinant upper/lower limit value of 1st,2nd,3rd separately.(reher to set operation of determinant upper/lower limit value of P12.1)
・ Can't set determinant outputwhen determinant upper limit value and determinant lower limit value are all set as 0.
・ Compare determinating with absolute value not determinate upper/lower limit.
・ Again st average test method,determinate upper/lower limit through real time.
・ Determinate upper/lower lomit value when express store data or record max value,degree in case of about open/close test method.

8
8.storage instrument function
8.1 1 store land
When in open/close test mode,through keep pressing MEM key to land the max value to storge open test mode
【open test mode】
Storge record(1st)
Storge record(2nd) Open(2st)
In case of exceeding 1000 data.
after one second,resert the max value and
return to test mode.
※1 use no data to express when 󳞛rst choice of open
※2 use no data to express when second choice of close
Storge record(3rd)
Torque
1st
MEM
MEM
MEM
MEM
MEM
MEM
2nd
3rd
Time
torque indicated
real torque
If keep pressing MEM key,when load the max value in
storge,resert the max height poin after 1 second.
Nm
1ST
2Nd
001
※1
※2
Nm
Nm
Open(1st)
Nm

9
After 1second,peak resert
Memory record
When data exceed 1000
It returns to original in 1 second.
【Close test mode】
indicate memory code
・ ・
indicate memory data
shift indication in
1 second distance
shift indication in
1 second distance
8.2 Memory indication
Memory indicate open test mode,then press RECALL key to enter memory indication mode.
Memory data of memory indication mode are 󳞛nally indicated.
Nm
Nm
Nm Nm
CNTCNT CNT
Nm
【When open 1st/close choosing】
enter 󳞛nal memory
code indicate data
shift indication in
1 second distance
cancel memory
testing
RECALL
RECALL
RECALL
enter test mode
Nm
Open
Close
Nm
001
MEM
Nm
ZERO
RST
RECALL

10
【When open 2nd/3nd choosing】
Indicate memory code
・ ・ ・ ・ ・ ・
Indicate memory data
Enter test mode
Nm
Enter 󳞛nal memory
code indicate data
Cancel memory
After indicating for one second
After indicating for one second
After indicating for one second
After indicating for 1 second After indicating for 1 second
After indicating for one second
when F01=3nd
when F01=2nd
After indicating for one second
testing
Enter final memory code
indicate data
RECALL
RECALL
・ ・
CNT
1ST 1ST 1ST
2Nd
3Rd
CNT CNT
ZERO
RST
RECALL
RECALL
Open
Close
Nm

11
8.3 Cancel final data
When 󳞛nal code,deta indicating keep pressing ZERO/RST key to cancel Data of 󳞛nal memory code.
Enter 󳞛nal memory code indicate data Indicate clear
Memory code
Enter 󳞛nal memory dat indicate data
At the time of the power off ：
MEM ＋ POWER Enter usual test mode
when F01=2nd
when F01=2nd
After indicating for 1 second
After indicating for 1 second
After indicating for 1 second
Enter usual
After indicating for 1 second
After indicating for 1 second
・ Keep pressing ZERO/RST key to cancel 󳞛nal data in condition of only one data leftThen main display part"nonE"indicating for 2 secong and return to test mode.
CNT CNT
1ST
2Nd
3Rd
8.4 Cancel all data (all memory data)
When the power is OFF,keep pressing MEM key and power key and power key ,then unclinch simultaneity. If keep pressing MEM ,the memory data of open
test and close test are all canceled.
CNT
No data
No data
（Indicating for about 2 second）
（Indicating for about 2 second）
ZERO
RST
ZERO
RST

12
● Record positing of storge data saved
storge data recorded by CSV form in 󳞛le SHIMPO of USB storge.
root directory
＋－－ SHIMPO ※ When there is no SHIMPO 󳞛le in USB storge,it will recorded automatically.
＋－－ ********.CSV
● File name format
Record 󳞛le name of storge data according to following provision .
$MMDD***.CSV
$ ： O （open storge data）、 C （close storge data）
MM ： month （01 ～ 12）
DD ： day （01 ～ 31）
*** ： continuous number ： 001 ～ 999 （As many as 999 pieces）
Code follow the max number of continuous month,day in SHIMPO 󳞛le.
9.USB memory save
9.1Ways for saving USB memory
9.2 Noticing code saved in USB memory.
USB memory save is to save .Peal hold value inputed in memory and it statistical data by keep pressing FILE key when in open/close test
mode. Besides,when saving in USB memory,determinating upper/lower limit by determinant upper /lower limit value setted and save the results.
Accessoral USB memory of approriative connector for USB memory on right side of mainframe close test mode.
Open Open
Mean Mean
Close Close
Nm
Nm
Nm
Open test mod and Close test mode
FILE LED lights when inputing
Finish inputing when LED off
Notes:FILE LED lights when visiting USB storge
Please don't touch USB storge before LED light off
Code Meaning Method management
U-10 No memory data save in USB memoring Peak torque,please load memory.
U-11
Don't insert into USB memory ・ Please insert USB memory .
・ Please connect USB memory again.
・ Please connect another USB memory.
U-12 No space in USB memory ・ Please increase the capacity of USB memory
U-13 Fail to visit USB memory ・ Please connect USB memory again
Please insert another USB memory
U-14
Can't make 󳞛le because there move all 󳞛le in 󳞛le SHIMPO
to computer is 󳞛le of continuous number 999
in 󳞛le SHIMPO
・ Move all 󳞛le in 󳞛le SHIMPO to computer
FILE
FILE
Sometimes indicate code in USB memory save.
After indicate code con󳞛rmation ,then pressing zero key to indicate clear.

13
9.3 Memory Data File Format
oper(3rd)Memory Data
Open (1)
Date,Jul/18/2007 15:29:24 (2)
Model,TNX-5 (3)
Unit,Nm (4)
Data,10 (5)
Step,3rd (6)
Denominator for SD,N-1 (7)
,1st,2nd,3rd
Maximum,0.427,0.367,0.429 (8)
Minimum,0,0,0 (9)
Average,0.2047,0.1646,0.1839 (10)
Standard Deviation,0.1281,0.1187,0.1188 (11)
Difference,187.8,216.3,193.7 (12)
Upper Limit,0.1,0.2,0.3 (13)
Lower Limit,0.05,0.15,0.25 (14)
Number of High NG,8,4,1 (15)
Number of Low NG,1,4,8 (16)
Defective rate(%),90,80,90 (17)
No.,Date,Time,1st,,2nd,,3rd, (18)
※ 1,Jul/18/2007,15:28:10,L,0.015,O,0.175,H,0.355
2,Jul/18/2007,15:28:47,H,0.116,L,0.145,L,0.157
(1)Measuring Mode:Open Memory Data(Open)Or Close Memory Data(CLOSE)
(2)Date:date of saving date in USB memory
(3)Model:TNX model
(4)Unit:torgue date unit
(5)Date number:number of torque date
(6)Open peak torgue:open peak torque(1st,2nd,and3rd)in case of measuring mode is open
(7)Standard deviation:installed denominator of standard deviation
(8)Max.value:max.value of torque date
(9)Min.valne:min.value of torque date
(10)Ave.value:ave.value of torque date
(11)Denominator of standard deviation:standard deviation of torque data
(12)Variation:variation of torque data
(13)Upper limit value:installed upper limit value(note)
(14)Lower limit value:installed lower limit valae(note)
(15)Upper limit NG:number of upper limit NG of torqne data(note)
(16)lower limit NG:number of lover limit NG of torque data(nate)
(17)Fraction dafective:fraction defective of torque data(note)
(18)Data contents:data contents of torque data
No:data number
Date:measuring date of torqne data
Time:measuring time of torqne data
1st:open 1st
2nd:open 2nd
3rd:open 3rd
data:close
(19)Measuring data:every comma,data contents in each measaring data
upper/lower limit result H:hi o:go l:lo
(19)
}
※ 1,Jul/18/2007,15:28:10,L,0.015,0,0.175,H,0.355
No.
(note)only upper/lower value is effective
month/date/year hour/minute/second
1st upper/lower valae
torque data
2nd upper/lower valae
torque data
3rd upper/lower valae
torque data

14
Denominator of standard deviation,variation,and fraction defective are calculated as follows.
Open(3rd)memory data Close memory data
variationr= （denominator of standard × 3/ave.value） × 100
fraction defectiver= （upper limit NG number ＋ lower limit NG number） /N × 100 Ｎ =memory data number
● In case of N-1
N-1
N
∑
∑
2
2
denominator of standard= (Xi -ave.value)
(Xi -ave.value)
denominator of standard=
ave.value= ∑Xi/N
Xi =measuring data N=memory data number
ave.value= ∑Xi/N
Xi =measuring data N=memory data number
● n case of N
10.Printing
10.1 Print for statistic data
10.2 Pringting example and printing format
Set function f06 into print prior to printing.(11.refer to function setting)
connect option printer with outer connector of back side of body
FILE
RECALL
CNT CNT
FILE
Open measuring mode
or
close measuring mode
Print compbeted by LED lights out
File led lights up in printing
measuring unit
data number
max.value
min.value
ave.value
stardard deviation
denomination of standard deviation
variation
upper limit value ※
lower limit value ※
data
data number ※ ： Only when a high and low test is
effective.
upper/lower limit result data number ※
h:hi empty:go l:lo
2nd:2lines
3rd:3 lines
}
over upper limit number data ※
over lower limit number ※
fraction defective ※

15
11.Function setting
11.1 Function mode
Function modes are as follows
11.2 Operation
Item Sub display Setting conterds Initial setting
Open peak torque F01 1st、 2nd、 3rd change 1st
Measuring unit F02 N ・ m、 N ・ cm change N・m
Display cycle F03 1、 2、 4、 8minites change 2
A/Dfelter F04 3、 20、 150 change 3
Auto powerOFF F05 OFF、 ON (10minites) change ON
Select of communication device F06 PC、 Print change PC
Change of outside output F07 ovEr、 Hi-Lo change ovEr
Denomination of standard
deviation F08 N-1、 N change N-1
In power off
1step （1st）
3step （3rd）
Measuring unit setting
Display cycle setting
N ・ munit N ・ cmunit
2step （2nd）
※ current setting is displayed first.
※ current setting is displayed first
＜ Open peak torque setting ＞
Open peak tonque is selectable frow 1 step,2step,or 3 step.
＋
POWER
＜ Measuring unit setting ＞
Measuring unit is selectable from N.m or N.cm.
ZERO
RST
Open
Close
Open
Close
Open
Close
F01
F01
F01
Open
Close
Open
Close
Nm Ncm
ZERO
RST
ZERO
RST

16
1 time/second
3msec
OFF （Prohibition) ON （10minutes）
20msec
150msec
2 time/second 4 time/second
8 time/second
ZERO
RST
＜ Display cycle setting ＞
In measuring mode display cycle is selectable from 1 time/second,2times/second,4 times/second,or 8 times/second.
＜ A/D 󳞛lter setting ＞
Sampling cycle are as follows depending on 󳞛lter response time
＜ Auto power off setting ＞
When auto power off is ef󳞛ctive on power on in use of battery,power becomes off automatically after 10 minutes no
operation.
*No operation of key touch,outside communication,current setting is displayed 󳞛rst.
and USB communication. Teme can not be changed from 10 minutes.
※ Cnrrent setting is displayed first
※ Cnrrent setting is displayed first
※ Cnrrent setting is displayed first
Open
Close
Open
Close
A/D 󳞛lter setting
Auto power off setting
Select of communication device
Filter response time Sampling cycle
3msec 1000numbers/second
20msec 1000numbers/second
150msec 150numbers/second
Input(actual load variation)
90％
Measuring numbe
90％ resporse time
F04 F04
F04
F05
F05
F03 F03 F03
F03
Open
Close Open Close
Open
Close
ZERO
RST
Open
Close
Open
Close
Open
Close
ZERO
RST
Open
Close

17
＜ Communication device sitting ＞
Set it connect voith printer or compnter
＜ Setting of outside output ＞
Set the single of ouerweighed ortput,outside output or ortside output of compare instrument.
＜ Denominator of standard deviation ＞
When calculating standard deviation,you can set denominator from N-1,N.
F06 F06
※ Cnrrent setting is displayed first
※ Cnrrent setting is displayed first
※ Cnrrent setting is displayed firs
Setting of outside output
Denominator of standard deviation
Set land,test mode
Connecting with computer
Overweighed output ※
Choose N-1 Choose N
Compare instrament output
※ Chift to overweighed output automatically
when connecting with electric torque.
Connecting with printer
Open
Close
F07
F08 F08
ZERO
RST
Open
Close
F07
Open
Close
Open
Close
ZERO
RST
Open
Close
ZERO
RST
Open
Close

18
Set daterminant upper/lower limit value on 4 lines that no singles,then decide decimal point.According to unit and type.
Choose 0,2,3,4...9 according through pressing recau key on 1~4 lines(press relall key to return o when 9)
move right by pressing mem key
Expless the location of choosing unit decimae point
Set the determinate lower limit value of compare instrument by pressing o key.
Please set deternuiant upper limit value>determinant lower limit value.
When determinant upper limit valne<deterninant lower limit value,lights of Hi,go,lo shine.press open/close key
to determinant upper limit value.
＋
POWER
RECALL
＜ Set determinant upper limit value of open 1st of lompare instrument ＞
＜ Set determinant lower limit value of open 1st of compare instrument ＞
Check out abnormality in power of in_out
Hi、 Go、 Lo LED Blinking
※ key operation is the same as the setting of determinant lower limit value of
compare instrument
Determinant upper limit value
設定変更開始
Move rightMove right
Move right line by line as preeing memkey
Determinant lower limit value
Retum to the 4th
when press the 1st mem key
Press recall key to add 1
RECALL
RECALL
RECALL
MEM MEM
ZERO
RST Set determinant lower limit value of open 1st of compare instrument
※ Cnrrent setting is displayed first
※ Cnrrent setting is displayed first
1 - H
1 - H
1 - H
1 - H 1 - H
ZERO
RST
ZERO
RST
1 - L
12. Set determinant upper/lower limit value12.1
Setting operation of determinant upper/lower limit value.

19
Please set throngh press the key as set determinant upper limit value of 1st.
return to the setting of determinant upper limit value as check out abnormality in
power of in_out.
2nd Determinant upper limit value
When F01=1sth,set towards to deterninant upper limit value of close.
When F01=2nd,set towards to deterninant upper limit value of close.
2nd Determinant lower limit value
3rd Determinant upper limit value
3rd Determinant upper limit value
Deterninant upper limit value of close
Deterninant lower limit value of close
Set land,test mode
12.2 Output the result of determination of compare initrument
Compare the test value(LCD indicating value)with the setting value of determinant upper limit input
the result of compare instrument according to the.....outside.
test value>set vakye if uppe limit value,output of compare instrument is ON.
test value<set valre of lower limit value,output of compare instrument is ON.
when the setting mode of instrument is shifting output,you have to set "Hi_Lo",so as to con󳞛m the effect of compart instrument.
ZERO
RST
ZERO
RST
ZERO
RST
ZERO
RST
ZERO
RST
ZERO
RST