Niigata seiki WR-100 User manual

mm
WIRE ROPE CALIPER WR-100
Model No.
User Manual
Thank you for purchasing the Wire Rope Calipers.
This product is designed for measuring wire rope diameter with precision and repeatability.
●For safe and proper use of this product, please read this instruction manual before use and follow the procedures
described. Keep this manual with the calipers for future reference.
●Keep this manual with the instrument if transferred or leased to a third party.
●For inquiries about this product, please contact dealer or Niigata Seiki at the address listed on the following page.
■PARTS IDENTIFICATION AND FUNCTION
SAFETY PRECAUTIONS
⑩Scale
⑨Battery Cover
④Lock Screw
⑤
[HOLD]Button
⑥Output Connector※１
③LCD Display
①Jaw
②Measuring
Surfaces
Read this manual and follow the instructions.
・Use of product other than as described in the manual
may cause accident.
Use only for measuring.
・Use for any purpose other than measuring may
cause damage or wear to the instrument. Improper
use may also cause accident.
Handle with Care.
・Do not drop or subject instrument to excessive shock.
Do not place under heavy objects. Improper handling
may cause damage or poor accuracy.
・Do not scratch instrument.
Before use, make sure measuring surfaces and
slide are clean of dirt and debris.
・Debris may cause damage to Display Unit or
erroneous reading.
Use and store only in environment meeting the
following conditions:
●Dry location protected from rain, water, and oils.
●Location that does not become hot.
●Location protected from use by children and
unauthorized people.
・Use in places contrary to the above may cause
damage to the product resulting in accident or injury.
Avoid using in locations with high electric fields, such
as near fluorescent lights or switching power supplies.
・May cause damage to Display Unit or erroneous
reading.
When Lock Screw is tight, do not slide the Display Unit.
・Will cause damage to Gauge.
Do not disassemble or modify.
・Doing so may cause accident or injury. Please
contact distributor or place of purchase for service.
⑦
[ON/OFF]Button
⑧
[ZERO]Button
※１：This feature not available.
①Jaw...................... For positioning on Object to be measured.
②Measuring ...........Surfaces for measuring Outside Dimension
Surfaces of object.
③LCD Display ........Displays digital measurement.
④Lock Screw .........Tighten to Prevent the slide and display from
moving.
⑤
[HOLD]Button
.......Will Hold value on Display.
⑥
Output Connecto r※１ ..Connector external output.
⑦
[ON/OFF]Button
........For turning power ON / OFF.
⑧
[ZERO]Button
...........Resets display to 0.00mm.
⑨Battery Cover ..........Cover for Silver Oxide SR44 Battery.
⑩Scale.......................Supports LCD Display Unit.
Please Observe
Always follow the proper operating procedures in order to prevent
harm to yourself or others, and to prevent damage to property.
Denotes a prohibition
-You MUST NOT do
Denotes a requirement
-You MUST do
Indicates risk of personal injury or property damage if not followed.
WARNING

Battery
Cover
OPEN
Correct
○Wrong
×
PREPARATION FOR USE
OPERATION
※Use one SR44 Battery
・Please wipe off corrosion protectant
with a soft, oiled cloth.
・Please insert Battery.
①Slide cover in direction of arrow.
②Insert battery with (+)side outward.
③Replace Battery Cover.
①Wipe off Corrosion Protectant Oil from Gauge using a soft
cloth moistened with oil.
②Remove any dirt or contamination from measuring surfaces
and slide before use.
③Check alignment of Measuring Surfaces by placing in fully
closed position and using light to verify that they are tight.
Make sure there is no gap between surfaces. (light does not
pass.)
Preparations to be performed after
purchase prior to first use.
①Press [ON/OFF]to turn ON power.
②With caliper Jaws fully closed, press the [ZERO]Button.
③When “0.00mm”is displayed on LCD, caliper is ready for
measurements
I263-K 1511
Ｑ．Nothing is displayed, or the numbers are flashing.
Ａ．The battery may be running low, please replace battery
with a new one.
Ｑ．With power on, the number on the LCD does not
change as Display Unit is moved.
Ａ．Please reset by removing battery for about 30sec., and
then replacing.
Ｑ．Nothing happens when buttons are pressed.
Ａ．Make sure battery is properly inserted.
Ｑ．The characters “MIN”, “MAX”, or “△” are displayed on
LCD.
Ａ．Cycle power, or apply several long presses to [HOLD]
Button. Use as normal once character is off.
AFTER USE CARE・STORAGE
TROUBLESHOOTING
●If Instrument is not working properly, or if you have any
questions, please contact distributor or place of purchase.
●Please note, manufacturer is unable to respond to inquires
or provide service directly. Please contact distributor or place
of purchase.
SERVICE
PRODUCT SPECIFICATIONS
Model No.
Resolution
Measurement Range
Instrument Error
Auto-Off Feature
Operating Temperature Range
Storage Temperature
Max. Response Speed
Weight
Power Supply
Battery Life
Accessories
WR-100
0.01mm
0-100mm
±0.05mm
approx. 20min.
0℃〜 40℃
-10℃〜 60℃
approx. 170g
Silver Oxide Battery: SR44・1.55V
approx. 1 Year with normal use.
Silver Oxide Battery: SR44 1.55V
(1x included for test)
●After use, wipe off any dirt or oil from measuring
surfaces, sliding surfaces, and exterior of Gauge using a
soft cloth and corrosion protecting oil.
Use thin coating of corrosion protectant or store in anti-rust
bag.
●Store with Lock Screw slightly loose and Jaws open
approximately 1mm to prevent excessive force caused
by thermal expansion.
Excessive forces may affect accuracy.
●Store in provided case in a cool, dry, location out of
direct sunlight.
Keep secure from unauthorized personnel.
●If Gauge will not be used for more than one month,
please remove battery to prevent damage from battery
leakage.
Absolute Measurement
Preparation Before Use
Relative Measurement
How to Position Object to Measure
CALIBRATION
●We recommend a regular accuracy check by periodic
calibration in order to insure measurement accuracy.
With extended use, the measuring surfaces will wear and
accuracy may be affected. We recommend implementing a
regular accuracy check.
We provide calibration services. Please contact
agent in country of purchase to make arrangements.
①Press [ON/OFF]to turn ON power.
②With caliper Jaws closed, or at any desired position, press0
the [ZERO]Button.
③When “0.00mm”is displayed on LCD, caliper is ready for
measurements.
※Exceeding the maximum response speed of caliper will lead
to erroneous reading on LCD.
Please do not move LCD slide violently.
Opening: 1.5m/s
Closing: 0.75m/s
Object to
Measure
Jaw
Object to
Measure
Jaw
Niigata seiki Co., Ltd.
6-15-22, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : [phone] Fax. : [phone]
MAIL:[email protected]
URL http://www.niigataseiki.co.jp