Nilfisk-Advance MH 3M User manual

MH 3M & MH 4M
SERVICE MANUAL
SM_MH 3M_4M Ver.1.2_May 2016

SM_MH 3M_4M Ver.1.2_May 2016
Preface
This service manual contains detailed description of the main repair work on the hot HPW
MH 3M & 4M.
Repair work requires a suitable testing workplace with the necessary water and power supply.
If operating errors are evident, refer the customer to the operating instructions.
A fault in the cleaner can have several causes as described in the section on troubleshooting.
Refer to the illustrated spare parts lists during repairs. They show the assembly position and the
sequence in which the individual components should be assembled.
See ”Technical Service Bulletin” (TSB) sheets. They include information on technical
modifications that have been made after this repair manual was printed.
”Technical Service Bulletin” sheets are also valid as a supplement to the spare parts list until
publication of a new edition.
Repair manuals and ” Technical Service Bulletin” sheets should be available at the site
where repairs are carried out.
It is not permitted to give them to third parties.
Use original Nilfisk spare parts only.

A.
B.
C.
D.
E.
F.
G.
H.
I. Special tools
Wiring diagrams
Adjustment / Test
Service / Repair
Troubleshooting
Function
Construction
Technical data
Safety instructions 4
5-24
25-40
41-56
57-59
60-81
82-90
91-98
99

SM_MH 3M_4M Ver.1.2_May 2016
Safety instructions
4
A
For your own safety
ESD measures
(electrostatic discharge)
Observe valid safety regulations
for electrical equipment. In
particular, observe the following
regulations:
IEC 60335-2-79
EN 60335-2-79
Additionally:
Also see national regulations
Before using the cleaner, always
read the operating instructions
and keep them readily available.
Only allow the high pressure
Repair work should be carried
out by persons instructed in
electrical installations or by
trained electricians only.
Take the following ESD precautions before carrying out any
repairs to the electronics:
 Touch the earth conductor before repairing the cleaner
( to discharge electrostatic charge from your body ).
 Wear wrist band if necassary.
 Use a conductive floor covering or a conductive table cover.
 Never touch the printed circuit board or electronic components
( always hold on to plastic ).
 Transport electronic components in conductive packaging
( e.g. ESD bag ).

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 5
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 6
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 7
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 8
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 9
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 10
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 11
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 12
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 13
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 14
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 15
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 16
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 17
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 18
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 19
B

Technical data
SM_MH 3M_4M Ver.1.2_May 2016 20
B