Nitgen NAC-2500+ User manual

NAC-2500 Terminal Installation
Guide

- 2 -
ⓒ Copyright 2003-20089 NITGEN Co., Ltd.
All rights reserved
To Contact Us
Tel. [phone]
(Toll Free)
Fax. [phone]
E-mail: [email protected]
URL: http://www.nitgen.com
Reproduction of part or all of the contents in any form is
prohibited other than in accordance with the permissions.
Product specification can be changed and upgraded to improve
functionality without prior notice.
NITGEN, NITGEN logo are registered trademark of NITGEN.

- 3 -
Table of Contents
1. Before Installation
1.1 To install ----------------------------------------------------------- 4
1.2 Product package ------------------------------------------------ 4
2. Installation Environment ---------------------------------------------- 6
3. System Configuration
3.1 Network mode ----------------------------------------------------- 7
3.2 Standalone mode ------------------------------------------------- 8
4. Installation
4.1 Fastening the auxiliary plate ---------------------------------- 9
4.2 Attaching other devices except the terminal -------------- 11
4.3 Connecting external cables ----------------------------------- 12
4.4 Fastening the terminal ----------------------------------------- 16
5. Check After Installation ----------------------------------------------- 18

- 4 -
1. Before Installation
1.1 To install
Please follow the installation guide because the performance
can be decreased if the product is installed incorrectly.
1.2 Product package
Product Pictures Qty Use
Terminal
1ea Access Controller
Adapter
1ea
Power cord
1ea
Supplying power for
the terminal
Rear case
1ea Fastening the terminal

- 5 -
4ea Fastening the terminalBolt
6ea Fastening the rear
case
Housing
1ea
Receptacle
& cable
5ea
Connecting door cable
S/W CD 1ea

- 6 -
2. Installation Environment
Please keep in mind the following conditions when you install the
product. You might need to obtain the user's consent if necessary.
① This product is originally designed to install indoors. If you
have to install it outdoors, however, do not expose the terminal
to direct sunlight, snow or rain.
② The connection cables should not be exposed outside, and it
is highly recommended to bury them underground. If that is
impossible, you must obtain the user's consent before
installation.
③ Power supply should begin after all connections are completed.
Do not disconnect the lines or make any additional
connections while the power is supplied.
④ If you install the product as an access controller at a proper
height for the users and in a near place that facilitates control
of the entrance, you can use it more efficiently.
⑤ The power requirement for the system is AC 100~240V,
50/60Hz.

- 7 -
3. System Configuration
3.1 Network mode
Terminals are connected by network and it can be remote
control.
Figure 3.1 Network Block Diagram
Network(TCP/IP)
Server PC Client PC
Terminal
LockDoor Open S/W

- 8 -
3.2 Standalone mode
One terminal is used independently. All settings such as user
registration, deletion, and access control are performed in the
terminal alone.
Figure 3.2 Terminal Block Diagram
Locking Device
Door Open S/W
Interphone

- 9 -
4. Installation
☞ The overall installation procedure is as follows:
① Fasten the bracket
② Attach other devices except terminal(locking device, interphone,
etc.)
③ Connect the external cables
④ Fasten the terminal
4.1 Fastening the auxiliary plate
① Decide where you want to install the product, and cut the
rear case as shown Figure 4.1 to make the hole for wiring.
Figure 4.1 Making the hole for wiring in the rear case

- 10 -
② Align the bracket with the hole for wiring as shown Figure
4.2, and fasten it with 6 bolts supported in the packet.
Figure4.2Fasteningrearcase

- 11 -
4.2 Attaching other devices except terminal
☞ You can attach the following devices. Refer to the specifications
of each device for more information on installation.
① Locking device
② Door Open button
■Types of installable locking devices and specifications
Type Specifications Remarks
Deadbolt input: DC12V,
1A or lower
Voltage output,
Fail Safe/Secure
Electronic
Magnetic-Lock
input: DC12V,
1A or lower
Voltage output,
Fail Safe/Secure
Electric Strike input: DC12V,
1A or lower
Voltage output,
Fail Safe/Secure
Auto Door *Maximum Switching Voltage:
220V DC,250V AC.
*Maximum Switching Current:
2A DC,AC or lower
Contact output
☞Fail Safe Type: UNLOCKED, Open Type on Emergency
☞Fail Secure Type: LOCKED, Close Type on Emergency
4.3 Connecting the external cables
☞ You should connect the following external cables.
But you don't have to install the network cables if the customer
doesn't request them.
① Door control cable
② Network cable
③ Power cable
④ Wiegand signal cable
⑤ RS485 cable

- 12 -
4.3.1 Connecting the door control cable (Main board J2)
■Specifications of the cable and material
Housing Receptacle Cable
5264-06 5263PBT UL Cable, 24~28AWG
☞ Connection Note
① Pay attention to terminal numbers when connecting the cable to
the connector.
② Contact output is used when installing on the auto door. So make
sure to set the terminal [JP1] as OPEN. The factory default of
the terminal [JP1] is JUMPER.
③ Some locking devices may not have door monitoring signals.
☞ JP1 is positioned back of the terminal, beside product label.
JP1 is jumper for supplying power(12V) to the door
lock. If you use the external power supply, those
jumper must be removed before connecting the
릴레이보드의
[JP1]
은
도어락의
전원을
공급하기

- 13 -
■How to connect cables by types of locking devices
Deadbolt/Strike/Electronic Magnetic-Lock
PIN
NO. Feature Fail
Safe Type
Fail
Secure
Type
Door
Monitoring
Door
Open
1 GND GND GND COM Open
button
2 Door Open button Open
button
3 Door Monitoring Monitor
(12/24V)
4 CONTACT_B VCC(12/24
V)
5 COMMON (COM)
6 CONTACT_A VCC(12/24
V)
*The Relay Boad [JP1]=>Close
Common
Contact_B
GND
Door Monitor
Door Open
Contact_A
Door Open Button
Power(Fail Secure)
Deadbolt
Power(Fail Safe)
Strike EM Lock
Door Monitoring Signal

- 14 -
Auto Door
PIN
NO. Feature Normal
Open
Normal
Close
Door
Monitoring
Door
Open
1 GND COM Open
button
2 Door Open button Open
button
3 Door Monitoring Monitor
(12/24V)
4 CONTACT_B Contact
5 COMMON Contact Contact
6 CONTACT_A Contact
*The relay board [JP1]=>Open

- 15 -
4.3.2 Connecting the network cable (Network board J3)
①Connect network lines as follows (pay attention to PIN numbers):
Schematic
Housing Cable PIN No Feature
1 TXP
2 TXN
3 RXP
RJ45, 8PIN UTP
6 RXN
4.3.3 Connecting the power cable
Connect 12V adapter to Relay Board J4.
Connect 5V adapter ro Main Board J3
'NOTICE : When you connect extend cable, make sure the
polarity(+, -) are correct'
4.3.4 Wiegand output (Main board J5)
Check if the external device is pull up. If it is not, connect J16 and
J17.
J5 Connection
PIN Number Function
1 GND
2 Wiegand 1
3 Wiegand 0
4 +5VDC

- 16 -
4.3.5 RS-485 (Main board J1)
* If the device needs a termimal resistance, connect J18.
J1 Connection
PIN Number Function
1 GND
2 TRX-
3 TRX+
4.3.6 Wiegand input (Main board J9)
* Wiegand input cannot be used with RF module.
J9 Conncetion
PIN Number Function
1 +5VDC
2 GND
3 Wiegand 0
4 Wiegand 1

- 17 -
4.3.7 Normal RF Module Option(J9): HID, MIFARE, EM
- JP2: 5VA
- R74,R75: 0Ω
- R72,R73: Open

- 18 -
4.3.8 SOC RF Module Option (J9)
- JP2: 3VA
- R74,R75: Open
- R72,R73: 0Ω

- 19 -
4.4 Fasten the terminal
① Assemble the terminal with the rear case as shown in
Figure 4.3.
Figure 4.3 Assebling with rear case
② Screwing the terminal as shown in Figure 4.4 with the 4
terminal screws supported in the package.
Figure 4.4 Screwing the terminal

- 20 -
③ If you did all the procedures described, the termimal
installation is completed as shown in Figure 4.5.
Figure 4.5 Teminal after the installaion