Noble House Home Furnishings Barstool User manual

CAUTION: This Barstool is NOT a TOY.
Keep your child / children at bay during the assembly process.
For turning the Barstool and to prevent damage to the Barstool, 2 people may be needed to
execute this action.
Assembly Instructions
Caution: You must read this before you proceed
Please look in the Seat Panel for Hardware Pack
BARSTOOL
Noble House Home Furnishings LLC 1

Label Picture Description QTY
ASeat Panel 1
BFront Leg Frame 1
CBack Leg Frame 1
DShort Support Bar 2
ELong Support Bar 2
Label Picture Description QTY
①
Screw (M6x35mm) 3
②
Screw (M6x65mm) 7
③
Bolt (M6X60mm) 3
④
Allen Wrench 1
Parts List
Hardware
Noble House Home Furnishings LLC 2

Assembly Steps
Overview
This Barstool has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Barstool, the
above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.
Assembly Preparation
Before Beginning Assembly:
FRONT FACING
x 3
x 7
x 1
Seat Panel (A)
Front Leg Frame (B)
Back Leg Frame (C)
Short Support Bar (D)
Long Support Bar (E)
x 3
Noble House Home Furnishings LLC 3

With assistance from your adult partner,
3.1) Position the Short Support Legs(D) to the assembled part in Step 2.
3.2) Position Front Leg Frame(B) to the assembled part in Step 3.1 and turn the Barstool onto the opposite side as shown in the above
picture.
3.3) Secure the Short Support Legs(D) and the Long Support Legs(E) onto the Front Leg Frame(B) using Screws (②) and the Allen
Wrench(④) as shown in the above picture.
Do not fully tighten the Screws.
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
With assistance from your adult partner, position the Long Support Legs(E) into the Back Leg Frame(C) as shown in above
picture.
Then using Screws(②) and the Allen Wrench(④ ), secure the Long Support Legs(E) to the Back Leg Frame(C).
Do not fully tighten the Screws.
Step 3
DE
3.1
3.3
3.2
Noble House Home Furnishings LLC 4

Step 5
Attach the Seat Panel(A) onto the assembled part in Step 4 as shown in the above picture.
With assitance from your adlut partner, lay down the Barstool as in the above picture, then use the Screws(①) and the Allen
Wrench(④ ) to secure the Seat Panel(A) to the Front Leg Frame(B) and the Back Leg Frame(C).
Do not fully tighten the Screws.
Step 4
With assistance from your adult partner, turn the Barstool right side up as shown in above picture.
Then using Bolt(③) and the Allen Wrench(④ ), secure the Short Support Legs(D) to the Back Leg Frame(C).
Do not fully tighten the Bolts.
D
C
B
Noble House Home Furnishings LLC 5

With assistance from your adult partner, turn the Barstool right side up.
Inspect it and make sure all parts are adequately connected.
Carefully sit onto the Barstool. This pressure will help align all parts at all joints.
Then get off the Barstool and proceed to tighten the Bolts abd Screws in a sequential manner.
When tightening the Bolts and Screws tighten sequentially.
DO NOT tighten any Bolt and Screw fully and then move on towards the next one.
If there are any wobbles after tightening, loosen the Bolts and Screws and execute this same process.
Adjust the Levellers until the Barstool is level with the ground.
To adjust the Levellers, get assistance from an adult partner to lift/lean and hold the Barstool while you are working.
Your Barstool is ready for use.
This Barstool can only be used on a flat, level surface.
Noble House Home Furnishings LLC 6