Noble House Home Furnishings Club Chair User manual

Label Picture Description QTY
A Chair Seat 1
B Backrest 1
C Right Armrest 1
Assembly Instructions
Caution : You must read this before you proceed
Club Chair
Parts List
Noble house Home Furnishings LLC 1 of 8

D Left Armrest 1
E Leg 4
Label Picture Description QTY
①Plastic Washer 7
②Double Head Insert 4
③Bolt 1
Hardware List
Assembly Preparation
Before Beginning Assembly:
x1
x4
x1
x7
x1 x1
x1
x4
Noble house Home Furnishings LLC 2 of 8

Assembly Steps
Overview
This Club Chair has multiple parts and may require up to 30 minutes
to assemble. To give you an overview of the Club Chair parts, the
above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with
the parts and steps before assembly.
Position the Chair Seat(A) on a clean, non-marring surface.
Unzipper non-woven Fabric and Remove the Backrest(B) , Leg(E) and
Hardware package as shown above.
Step 1
FRONT FACING
Leg(E)
Chair Seat(A)
x7
x4
Chair Seat(A)
Backrest(B)
Right Armrest(C)
Left Armrest(D)
x1
x4
x1
Backrest(B)
Noble house Home Furnishings LLC 3 of 8

Step 2
Step 3
Slide the Double Head Insert(②) on the Left Armrest(D) into the Double Head
Insert(②) on the Chair Seat(A) as shown in the picture.
Note: Make sure the Double Head Insert(②) on Left Armrest(D) lock into the
Double Head Insert(②) on the Chair Seat(A).
Assistance from an adult partner is necessary for this assembly process.
Repeat the same step to install Right Armrest(C).
During this assembly process - do exercise caution. You may need to use your
hand to press down and or pave away the padded surface to facilitate the 'slip
and slide' assembly.
Caution: Ensure that your fingers do not get caught or pinched in the assembly
process.
Position Left Armrest(D) on its back,put Double Head Insert(②) into Left
Armrest(D) as shown above.
Repeat the same step to put Double Head Insert(②) into the Right Armrest(C).
Chair Seat(A)
Left Armrest(D)
Left Armrest(D)
Noble house Home Furnishings LLC 4 of 8

Step 4
Step 5
Attach the Backrest(B) to the Chair Seat(A) by pushing the Backrest (A)
downwards until the Backrest(A) is fully slotted and locked into position with
Chair Seat(A).
Chair Seat(A)
Backrest(B)
Chair Seat(A)
Noble house Home Furnishings LLC 5 of 8

Put the Chair Seat(A) on its back as shown.
Attach the Backrest(B) to the Chair Seat(A) Using Bolt(③) by turning clockwise
until tight as shown above.
Then close the non-woven Fabric zipper.
Install the Leg(E) onto the bottom of the Chair Seat(A) by putting a
Plastic Washer(①)(optional but improves security and tightness),
onto the threaded stem. Insert the threaded stem into the threaded
hole at each corner of the bottom of the Chair Seat(A). Tighten the leg
by turning clockwise.
Repeat the same steps to install the remaining 3 legs.
Step 6 Leg(E)
Chair Seat(A)
Noble house Home Furnishings LLC 6 of 8

Your Club Chair is ready for use.
Your Chair can only be used on a flat, level surface.
Step 7
Noble house Home Furnishings LLC 7 of 8

Noble house Home Furnishings LLC 8 of 8