NORTH STATES 5323 User manual

INSTRUCTIONS FOR MODEL
5323
Intended for use with children 6-24 months
INSTRUCTIONS FOR MODEL
5323

IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE
Important Safety Information
There is a gap between your gate frame and handle. This is not a defect. The gap on your
gate will close once it is properly mounted.
• Do not use the product if any components are broken or missing. If parts are required
please contact our Customer Service Department (contact information on the rst page).
Do not use replacement parts other than those approved by the manufacturer or
distributor. Non-approved spare parts may render the repair or the product unsafe.
Replacement parts can be ordered at www.northstatesind.com
• Check regularly that all ttings and components are secure and that no components are
worn, broken or missing.
• Check regularly that all ttings are securely tightened and that the locking mechanism is
working properly.
• Any damage to property during installation of your safety gate is the sole responsibility of
the end user.
• We recommend that you carry out the installation away from small children as some
components may present a choking hazard when loose.
WARNING
• Children have died or been seriously injured when gates are not
securely installed. ALWAYS install and use gates as directed using all
required parts.
• STOP using when a child can climb over or dislodge the gate.
• Install only with locking/latching mechanism securely engaged.
• To prevent falls, never use at top of stairs.
• NEVER use to keep child away from pool.
• This product will not necessarily prevent all accidents.
• NEVER leave child unattended.
• Periodically check all fasteners to be sure they are tight and secure,
stop using gate if any parts are missing or become damaged.
A. Bolt with Rubber Pad
B. Tension Knob
C. Tape Pad
D. Wall Cup
E. Screw
F. 1-Bar Extension
G. Small Upper Extension
Adapter
H. Small Lower Extension
Adapter
I. 2-Bar Extension
J. 4-Bar Extension
K. Large Upper Extension
Adapter (2)
L. Large Lower Extension
Adapter (2)
M. Gate Frame
N. Wrench
Your safety gate contains the following:
x4
A
B
C
N
L
M
K
I
D
E
x1
Page 2
F
G
H
L
K
J

Page 3
Installation
Step 1 • Measure width of opening.
• Refer to gures 1A – 1H to determine the correct installation.
1A 1B
1C 1D
1E 1F
1G 1H
29.75”-32.5”
(75.5 to 82.5 cm)
33”-35”
(83.8 to 88.9 cm)
With 1-Bar Extension
35.4” – 37.8”
(89.9 to 96 cm)
With 2-Bar Extension
37.8” – 40.6”
(96 to 103.1 cm)
With 1-Bar and 2-Bar Extensions
49” – 52”
(124.5 to 132.08 cm)
With 1-Bar, 2-Bar and 4-Bar Extensions
41” – 43.3”
(104.1 to 110 cm)
With 4-Bar Extension
43.3” – 46.1”
(110 to 117.1 cm)
With 1-Bar and 4-Bar Extensions
46.1” – 48.8”
(117.1 to 124 cm)
With 2 Bar Extension and 4-Bar Extensions

Step 2 • To add an extension, begin by removing both the upper and lower
plugs from the side of the gate frame. You may need to use a athead
screwdriver to remove the plugs. Figure 2A.
• Attach both the upper and lower adapters to the extension pole.
• Install the fully assembled extension by inserting the upper and lower
extension adapters into the gate in the holes where you removed the
plugs. Figure 2B.
• Reinsert both plugs, then insert the bolts with rubber pads into the
holes on the outside of the extension. Figure 2C.
2A 2B 2C
IMPORTANT: When installing multiple extensions, place as equally as possible
on either side of gate frame. The 1-Bar Extension must be inserted into gate
frame before adding an additional extension.
Page 4
Upper plug
Lower plug
1

Page 5
Step 3 • Install wall cups.
• Place the gate in the opening so that the bottom of the gate
frame is completely at on the oor. Figure 3A.
• Secure the gate, fasten the mounting cups to the wall by
aligning them with the bolts with rubber pads. Use double
coated tape or screws provided as shown in gure 3B.
IMPORTANT: Never install this gate without mounting cups!
Step 4 • Mount your gate
• Place the gate where you want to install it, then extend all 4 bolts
with rubber pads until they reach the walls. Ensure that the ends of
the bolts with rubber pads are seated inside the mounting cups.
3A 3B
Gate
Floor

Page 6
• Tighten both of the bottom tension knobs by turning them
clockwise at the same time. Figure 4A.
• Tighten both of the upper tension knobs by turning them
clockwise at the same time, so that the gap between the gate and
upper right corner comes together, leave 1.5 ~ 2 mm gap as shown
in gure 4B.
4A 4B
4C 4D
• Use the wrench provided to ease turning the tension knobs. Figure 4C.
Note: When securing the gate in the opening, the distance between
the gate frame and the opening should not exceed 2 ¾” on either
side of the gate and the 4 tension bolts should be equal as shown in
gure 4D.

Opening the gate: Pull back the button on the top of the handle with your
thumb, squeeze the trigger on the lower side of the handle, then lift the inner
door up and open the door.
Page 7
Operation
2
1
Closing the gate: Your gate has an easy-close feature. You can leave the gate
in the open position and when ready, simply push the gate door closed until it
clicks.
Note: Always check the handle, bottom swing guard and inner tabs to make
sure that the gate is securely locked, and never leave your child unattended.
3
3

Page 8
Rotate the knob downward on the gate stopper to determine the direction
the gate door will swing. Gate opens in both directions when gate stopper is
not rotated. To fully lock, lower the gate stopper to the locked position on
both sides of the gate.
Swing Control Operation
CLEANING: Clean the safety gate using warm water and mild detergent. Use a
soft cloth or sponge to avoid scratches. Never use solvents or chemicals to
clean the safety gate.
For instructions in Spanish or French, please visit www.northstatesind.com
Care
Locked position
Distributed exclusively in
the United States by
North States Industries, Inc.
5455 Highway 169 N
Plymouth, MN 55442
www.northstatesind.com
Manufactured in China
Rev 11/2019