NORTH STATES 4928 User manual

Quality Products
for the way you live
Intended for use with children 6-24 months
IMPORTANT: PLEASE KEEP FOR FUTURE REFERENCE!
For helpful tips and instructions, please visit our website:www.northstatesind.com or
contact our Customer Care department via email: [e-mail]
Phone: [phone] or Toll Free: [phone]
INSTRUCTIONS FOR MODEL
4928

WARNING
• Children have died or been seriously injured when gates are not securely
installed. ALWAYS install and use gates as directed using all required parts.
• STOP using when a child can climb over or dislodge the gate.
• Install only with locking/latching mechanism securely engaged.
• NEVER use to keep child away from pool.
• This product will not necessarily prevent all accidents.
• NEVER leave child unattended.
• Periodically check all fasteners to be sure they are tight and secure, stop
using gate if any parts are missing or become damaged.
• Hardware is included for use in solid materials only, such as wood or metal.
!
Page 2
Your safety gate contains the following:
x8 x2
x1
ABC
D
A.
B.
C.
D.
Screws
Upper Wall Mount with Pin
Lower Wall Mount with Pin
Gate Frame
To ensure safe operation, additional or replacement parts should be obtained only from North States or
its authorized distributors. Contact information appears on the cover of these instructions. Replacement
parts can be ordered at www.northstatesind.com
Any damage to property during installation or your safety gate is the sole responsibility of the end user.

Page 3
1. MEASURE OPENING
OPENING
72"
OPENING
38 1/3”
The gate can easily be adjusted to accommodate openings from 38 1/3" to 72" as shown above.
If the opening is smaller than 72" you will need to angle the gate at the pivot points to fit the opening.
Installation
2. WALL MOUNTING - Follow steps 1-3 as illustrated below at both ends of the gate
First, take enclosed mounting template and cut on cutting line. Place template on both sides of opening.
Locate the mounting template vertical to the
floor and mark the screw holes.
Mount the upper and lower wall mounts onto the
wall or flat surface with screws provided.
Extend the folded gate.
Unfold the sides of the barrrier to fit in your space.
FIGURE 1 FIGURE 2
WallWall WallWall
Do not mount hinges into sheetrock or plaster. Hardware is included for use in solid materials only such as wood or metal.
Do not allow gate to swing over the stairs.
Place the gate in the opening so that the bottom of the gate frame is completely flat on the floor.
Do not angle gate towards the top of stairs.
WARNING:When installing at the Top of the Stairs
•
•
•
•
FLOOR

FIGURE 5A
Page 4
3. SECURING GATE PANELS
Rotate both removable vertical
bars counterclockwise until they
are tight.
FIGURE 3
Note: Release by turning the
removable vertical bar clockwise
prior to folding or moving the gate.
TO CLOSE THE WHOLE BARRIER
Lift the gate. Press the push button. Hook the upper pin, and then
release the push button.
Operation
FIGURE 5B FIGURE 5C
TO OPEN THE ENTIRE BARRIER
Press the push button. Lift the gate to open.
Keep pressing the push button
until the gate is open.
FIGURE 4A FIGURE 4B FIGURE 4C

Page 5
Press and hold the door release
button.
Lift the door panel upward. Swing door open and release
button.
TO OPEN AND CLOSE THE DOOR
While the door is open, release it and it will close automatically.
NOTE: To ensure safety, always check to make certain that the gate is securely locked after it has been closed.
To close gate, push gate gently toward frame.
STAY-OPEN SYSTEM
FIGURE 6A
FIGURE 7
6B 6C
The stay-open feature should be used only by adults. When it is activated, the auto-close feature is
temporarily disabled, rendering the gate ineffective as a child barrier.
To activate the stay-open feature, merely swing the gate to its fully open positions to hold the gate open
for easy access.
TO FOLD THE BARRIER FOR EASY STORAGE
FIGURE 8A FIGURE 8B FIGURE 8C
4

Page 6
Alignment marks are now in proper position.
Retighten screw on upper locking housing.
Lock Troubleshooting and Adjustment
If the lock alignment indicators do not line up as in figure 9D, please make the following
adjustments to make sure that the door panel an be auto-closed.
If the mark on the upper locking housing is displaced to the left (9A) or right (9B) then:
Loosen the screw on the upper locking housing as shown in figure 9C adjust the gate until the marks are
aligned as shown in figure 9D.
FIGURE 9A 9B
9C 9D
Please use two screwdrivers when tightening
or loosening the screw.
If the upper locking housing is displaced upward 9E or downward 9F.
Loosen the screw on the door lower hinge.
Press the door panel and the lower door hinge towards each other as shown in figure 9G
until the two marks illustrated in 9D are aligned.
Retighten the screw on the door lower hinge.
9E 9F 9G

Page 7
1. Do not use the product if any components are broken or missing. Do not use
replacement parts other than those approved by the manufacturer or distributor.
Non-approved spare parts may render the repair or the product unsafe.
2. Check regularly that all fittings and components are secure and that no
components are worn, broken or missing.
3. Check regularly that all fittings are securely tightened and that the lockinge
mechanism is working properly.
IMPORTANT SAFETY CAUTIONS
CLEANING: Clean the safety gate using warm water and a mild detergent.
Use a soft cloth or sponge to avoid scratches. Never use solvents or chemicals to clean the safety gate.
CARE

Distributed exclusively in the United States by
Page 8
North States Industries, Inc.
5455 Highway 169 N
Plymouth, MN 55442
www.northstatesind.com
Manufactured in China
Rev 9/2019