NSS PREDATOR CXC150 User manual

PREDATOR CXC150
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS
BEFORE OPERATING OR SERVICING MACHINE
DANGER!
Failure to ObserveThese Instructions Can Cause Personal Injury
to Machine Operator, By-standers or Possible Machine Damage.
SAVE THESE INSTRUCTIONS
•NEVER attempt to service or perform maintenance functions while machine is plugged into an electrical
outlet.
•ALWAYS unplug machine before attempting to service the motorized brush attachment.
•NEVER operate in standing water. NEVER expose to rain. ALWAYS store indoors.
•NEVER overfill recovery tank or allow water to enter vacuum standpipe.This will cause damage to the
vacuum motor and possible electrocution.
•NEVER operate machine with a cut, abraded or taped cord.
•NEVER operate machine with a broken grounding blade on the plug.
•ALWAYS replace the entire cord when the cord or plug is damaged in any manner.
•NEVER handle the machine, cord or plug with wet hands.
•NEVER drop or insert any object into any machine opening.
•ALWAYS keep face, fingers, hair or any other body part, or loose clothing away from any machine
opening or any moving part, particularly the revolving brush.
•NEVER leave the machine unattended when plugged in. Unplug the machine from the electrical outlet
when not in use.
•ALWAYS turn the machine off before unplugging it from the electrical outlet.
•NEVER operate this machine in the presence of flammable or combustible liquids or fumes.
• When any electrical motor, switch, cord or plug service is required, maintenance should only be done by
an authorized service station, an electrician or other qualified persons.
•NEVER operate this machine if it is not working properly, if it as been dropped, damaged, exposed to
weather, or dropped into water. Return the machine to a service center for examination and repair.
•NEVER operate this machine with any air opening blocked. Keep all air openings free of dust, lint, hair,
ect.
•NEVER operate this machine without solution tank filter screens or vacuum standpipe filter screen in
place or if they are clogged. Clean all filter screens after every use.
•ALWAYS store this machine indoors. Protect it from rain or snow.
•NEVER spray the top of the machine with liquids.
•DO NOT pull or carry this machine by the electrical supply cord, use the cord as a handle, close a door on
the cord, pull the cord around sharp edges or corners, or expose to heated surfaces.
•NEVER disconnect the plug by pulling on the cord.To disconnect the cord from the outlet grasp the plug,
not the cord.
•ALWAYS unplug this machine before attempting to service.
•ALWAYS use a defoamer which will prevent a buildup of foam in the recovery tank. If a defoamer is not
used, the motor can be damaged from shampoo being pulled into the vacuum motor.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INFORMATION & OPERATING INSTRUCTIONS
DO NOT OPERATE MACHINE UNTIL YOU HAVE READ THIS SECTION
IMPROPER USE OF THE PREDATOR CXC150 WILL VOID THE WARRANTY
1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.
2. To keep fitting and lines from damage during freezing conditions, use an
anti-freeze in the pump and heater or keep equipment inside heated areas.
3. Do not let pump run dry.
4. Use neutral pH, water-based products only - NO SOLVENTS!
INSPECTION:
Carefully unpack and inspect the PREDATOR CXC150 for shipping damage. Each unit is
tested and inspected before shipment. Any damage incurred is the responsibility of the carrier,
who should be notified immediately.
CLEANING SOLUTIONS:
We recommend liquid cleaning chemicals. Powders may be used, but unless mixed very
thoroughly, they could cause build-up in the lines, pump, quick-disconnects, etc. A pH of 7-9 is
strongly recommended to avoid premature pump wear, which would void the warranty.
MAINTENANCE:
For optimum performance, flush the machine with clear water at the end of each working day.
Once a month, minimum, run a flushing compound through the machine to cut any alkaline
build-up that may have formed.
Lubricate wheels, casters and hinges as needed. The pump and vacuum motors do not require
any maintenance.
The body can be cleaned with a general all-purpose detergent and protected with a silicone
type product like Armor All®.The quick-disconnects should be lubricated with silicone, also.
Prior to each job, inspect the holding tank filter and the recovery tank float filter for hair and dirt.
The drain valve should also be inspected regularly and kept free of any debris or build-up.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

SET-UP:
Fill the holding tank with clear water and the detergent of your choice. Mix well.The addition of
warm or hot water to the holding tank would be a plus factor.
1. Plug in the cord. (This cord runs the pump and vacuums).
2. Turn on the pump and spray through the cleaning tool for a few seconds to fill the lines with
solution.
BALL FLOAT VACUUM SHUTOFF:
When the recovery tank is full, the ball float system will shut off the incoming air flow and
prevent water from entering the vac motors.The float will not work in heavy foam. Always use a
defoamer to prevent overflow. Once the float is activated, the vac switches must be turned off
and the recovery tank emptied.
CAUTION: To avoid vac motor damage, always make sure the filter is clean and the float
travels freely before turning on the machine. Use a defoamer whenever foam is present.
Water damage to the vac motors is not covered by the warranty.
SAFETY PRECAUTIONS:
All extension cords must have a rating of at least 12/3 (#12 cord). Extension cords should be
no longer than 50 feet. Replace the plug immediately if the ground prong becomes damaged
or is broken off.The ground is necessary for safety.
21
VACUUM SWITCH (1 & 2 : Each switch turns on one vac motor. Turn both switches
on for maximum lift. The vac switches illuminate when
turned on.
PUMP SWITCH (3 : This switch will illuminate when the pump is on.
(3)
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION
#1 4091231 Drain Gate
#1A 4093041 Spout, for Drain Gate
#2 4090581 Screw, 10-32 X 5/8, S/S
#3 4091251 Latch
#4 4091161 O-Ring, Thin
#4A 4091171 O-Ring, Thick
#4B 4090701 Nut, Cast Aluminum
#5 4093191 Vacuum Tank, Black, specify model
#6 4091241 Hose Barb, 1-1/2”, plastic
#7 4091291 PVC Elbow, 1-1/2”
#8 4091391 Gasket, for Vacuum Dome
#9 4091581 Vacuum Dome
#10 4091571 Vac Shut-off, manifold Assy.
#10A 4091501 Ball & Cage
#11 4090701 Nut, Cast Aluminum
#12 4091171 O-Ring, Thick
#13 4091291 PVC Elbow, 1-1/2”
#14 4091121 Hose Clamp, size 28
#15 4093131 Hose, Rubber, 2”X 24”
#15A 4093141 Hose, Rubber, 2”X 13”
#16 4090691 Washer, Vulcanized Fiber
#16A 9122470 Washer, Brass,1”OD X9/16ID X 1/16”
#17 4093091 Nipple, !/4 p.t., S/S
#17A 4091611 Bushing, Vulcanized Fiber
#18 4093171 Stop Chain, 12”
#19 4091181 Split Ring
#20 9120930 3/16 Flat Washer, ZP
#21 9120900 1/4-20 Hex Nut, w/Ny-Lok, ZP
#22 4091211 Vacuum Motor, 2-stage
#23 4091431 Gasket, Vac Motor
#24 4091651 Manifold, Vacuum, #3 or #4
#25 4090631 1/4-20 X 5”Hex Bolt
#26 9120930 3/16 Flat Washer, ZP
#27 9120920 1/4 Hex Nut, Finish
#28 4091651 Manifold, Vacuum, #3 or #4
#29 9120900 1/4 Hex Nut, w/Ny-Lok, ZP
#30 4091401 Chrome Handle
#31 4090601 1/4-20 x 3/4 Screw, Flathead Philips
#32 4091031 Quick Disconnect, male, 1/4 p.t.
#33 4091411 Exhaust Flange
#34 4091311 Louver, 3”(includes 3 screws)
#35 4091261 Latch Strike
#36 4091081 Elbow, Brass, 1/4 pt 90
°
#37 4091331 PVC Reducer
#38 4091151 Cord Retainer w/Strain Relief
#39 4093211 Axle, 1/2”X 17-1/2”
#40 4091361 Wheel, 8 inch, non-marking
#41 4091021 Axle Cap
#42 9120900 1/4 Hex Nut, Ny-Lok, ZP
#43 4091141 Axle Bracket
#44 4090611 1/4-20 X 3/4”Hex Bolt, ZP
#45 4094041 Base, Black (specify model)
#46 4093051 Castor, 4”swivel
#47 4093181 Holding Tank, Black (specify model)
#48 4092031 Hose Barb, Brass
#49 4091191 Filter, Pump Inlet, 40 mesh, S/S
#50 4093201 Lid, with label (no hinges)
#51 4091131 Hose Clamp, 3/8 - 7/8
#52 4093071 Pump, (no fittings), 150 PSI
#53 4091101 Hose Barb & Elbow, Plastic
#54 4093021 Hose Barb, Straight, Plastic
#55 4093121 Hose, Pump Inlet, 3/8”X 13”
#56 4091541 Hose, Pump Outlet, 3/8”X 48”
#57 4090091 Switch Plate (empty), CXH150
#58 4090511 #4 X 3/8”” Screw, Panhead, S/S
#59 4091041 Switch, SPST, Covered, w/light
#60 4093011 Hose Barb
#61 4093151 Funnel, Black
#62 4090541 6-32 X 2”Screw, Panhead, S/S
#63 4090531 6-32 Hex Nut with Ny-Lok
#64 4091441 Cooling Fan, 100 CFM
#65 4091451 Fan Guard
#66 4090071 Label, NSS
#67 4091611 Gasket
#68 4091521 Cord Wrap, Black
#69 4090671 3/8 Acorn Nut, Nickle Plate
#70 1391161 Washer, Plastic 5/8OD X 3/8ID X 1/16
MISCELLANEOUS ASSEMBLIES/PARTS
4091461* Thermistor Control Kit w/Potentiometer
& Probe
4091471* Thermistor Control Kit w/Potentiometer,
Probe & Cutout
4093161 Drain Gate Assembly, complete with
O-Ring & Nut
(NOTE: Items in kits not sold separately.)
PREDATOR CXC150
PARTS LIST
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

PREDATOR CXC150
PREDATOR CXC150
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

COMMON STAINS AND CLEANINGTREATMENTS
TREATMENT METHODS
First: Remove excess material by blotting to absorb liquids, or by scraping with a dull edge
(butter knife) is a solid.
Second: Clean the remaining stain as directed by the chart below. Always follow the direction
on the container. Apply the cleaning material directly to the stain (avoid over wetting
the carpet or upholstery), then remove the loosened stain material with a white ab-
sorbent cloth or tissue.
Third: When the carpet is dry, gently brush the carpet pile to restore its appearance.
Note: Treat unknown stains with a volatile solvent first and follow with other agents as re-
quired. If you are uncertain of the effect of the cleaning agent on the carpet fiber or
dye, test on an inconspicuous area first.
STAINTYPE TREATMENT MATERIAL
Asphalt Volatile solvent/detergent
Beer Liquid detergent, White vinegar
Berry stain Liquid detergent, Ammonia 3-6%, Water
Bleach Liquid detergent, Water
Blood (dried) Warm detergent, Ammonia 3-6%, Water
Blood (wet) Liquid detergent, Water
Butter Volatile solvent
Catsup or Mustard Liquid detergent
Chewing gum Volatile solvent
Chocolate Liquid detergent, Ammonia water
Coffee Detergent, White vinegar, Volatile solvent
Cola drink Liquid detergent
Creme de Menthe (green) Liquid detergent
Egg (raw) Liquid detergent
Food dye Liquid detergent, Water
Furniture dye or polish Paint/Oil/Grease remover, Detergent
Gravy Liquid detergent
Lipstick Paint/Oil/Grease remover
Mascara Paint remover, Volatile solvent, Detergent, Water
Milk Liquid detergent
Orange drink Liquid detergent, Water
Shoe polish Heated iron into clean towel, Volatile solvent
Tea Liquid detergent
Tomato Juice Liquid detergent
Urine Liquid detergent, Water
Vomit Warm detergent, Water, White vinegar
Wine Liquid detergent, Ammonia 3-6%, Water, Vinegar
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

6/27/01
FAN
SW
SW
BLACK
BLUE
WHITE
VAC 2
VAC 1
SW
ORANGE
ORANGE
WHITE
BLACK
GROUND
WHITE
VACUUM
VACUUM
PUMP
CORD 1
PREDATOR CXC150
WIRING DIAGRAM
120V & 240V
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

PREDATOR CXC150 ORIG 05-00 9094008 WHW REV. B 08-01
NSS ENTERPRISES, INC.
3115 Frenchmens Road, Toledo, Ohio 43607
PHONE: [phone] ■FAX: [phone]
NSS®Enterprises, Inc. European Distribution Centre
Unit II, Pinfold Trading Estate 55 Nottingham Road
STAPLEFORD, NOTTINGHAM NG9 8AD ENGLAND U.K.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080