Nucraft Flow XT User manual

Flow XT Installation Instructions
ID:

Before Beginning Installation
•Read through the entire instruction thoroughly
•A minimum of 2 persons is required for this assembly
•These instructions reflect typical assemblies. They may not match your specific configuration.
•Tables 120” and less are shipped with beams and power island attached to the bases.

Required Tools
•Drill Driver
•#2 and #3 Phillips Bit
•5/32” Drill Bit
•¼” Allen Wrench
•1/8” Allen Wrench
•Level
•Draw-Tight Fastener Tool (included)

Included Hardware
•Bolt – 3/8” UNC x 5/8” L-HW2248
•Screw –10-12 x 1-1/4” PHIL
•Screw - #12 x 1” PAN-PHIL
•Draw-Tight Hardware
•Bolt –5/16 –18 x 5/8 Fit Socket Head Cap (post base leg only)

Flow XT Table

Flow XT Table Exploded
1. Top
2. End Base
3. Center Base
4. Main Beam
5. Power Island
6. Power Island Mounting Bracket
7. Beam Shroud
1
2
3
4
5
6
7

Installation Prep –3-Piece or 4-Piece Tops
•3-Piece and 4-piece tops include gussets for extra support.
–Locations are marked on the main beam.
•Slide the gusset’s clamp bar onto the main beam BEFORE attaching the beam to the bases (facing
outward).
•Tighten the 5/16 –18 hex bolts.

Step 1: Tables over 120”
•Locate the beam labels and match for correct placement of the bases.
•Loosen clamp bars from base.
•Attach end bases by sliding the clamp bars into the beams.
–Beams should be 1/8” from the top of the base panel.
•Tighten cap screws to secure.
•Repeat to attach beams to center base. Keep beams tight and flush at the joint.

Step 2: Power Island
•Level the frame by adjusting the base glides.
–BEFORE adding the power island.
•Place power island onto frame. Use the 3/8” x 5/8” UNC bolts to hold the power island brackets to
the beams.
–Keep bolts loose to allow location adjustments when top is later added.
–Tables with shipped beams and power island attached to bases, loosen the cap screws on the
brackets to move freely on beam.

Step 3: Storage Well Installation (if applicable)
•Place the storage well in the power island.
•Attach the well to the power island using the bracket and ¼ - 20 x ¾ PHIL flat fastener.
•Tighten the fastener to ensure no gaps.

Step 4: Top Installation
•Open the doors on the power island to avoid damage to the top.
•Slide the top within 4 inches of the two halves connecting. STOP. Close the doors on the power island
before continuing to join the two halves.

Step 5: Work Surface Alignment
•Align the “L” shaped notes on the bottom of the top with the corners of the bases.
•Center the power island with the top before fastening to the bases.
•With multi-piece tops, join the pieces with the provided draw tight hardware.
•Fasten the work surface with the 1” #12 screws and brackets provided.
“L” Shaped
Notes
Draw Tight
Hardware

Step 6: Fastening
•Fasten these to the underside of the top with 1” #12 screws.
–Storage Well
–Power Island Brackets
–Gussets from the frame
•Tighten the cap screws that attach the power island to the beams
•Install the supplied shroud on the bottom of the frame using the 10-12-1/4” screw.

Power Island Trouble Shooting
•Power Island flush to table surface:
•When the power island is not flush to the underside of the table, loosen the cap screws that connect
the mounting bracket to the power island.
•Push the power island up against the underside of the table and retighten the bolts.
•Work around the table for each bracket.

Power Island Trouble Shooting cont.
Power Island Door Alignment:
•When the power island doors are not aligning or laying flush to one another, use a rubber mallet to
lightly tap into place.
–Open the door slightly, and tap until the door aligns. Repeat for each affected door.
•Use a 1/16” Allen wrench to tighten the hinge attachment screws.
•This does not work for storage well doors. In this case, adjust the hinges to better align the doors.

Flow XT Table –Post Leg Base

Flow XT Table –Post Leg Base Exploded
1. Top
2. End Base
3. Center Base
4. Main Beam
5. Power Island
6. Power Island Mounting Shroud
7. Beam Shroud
1
2
4
3
1
6
7

Installation of Post Leg Base
•Slide the clamp bars from the end base into a beam.
•Tighten the screws that fasten the end baes to the beam.
•Then continue with Step #2 in instructions above.