Nucraft Saber Collection User manual

Saber Collection™Installation Instructions
ID034 – Saber Conference Installation
Revision M – 8/12
Pg. 1 of 2
If you have any questions regarding installation, please call
Nucraft Customer Service at 1
Nucraft Customer Service at 1Nucraft Customer Service at 1
Nucraft Customer Service at 1-
--
-877
877877
877-
--
-N CRAFT
N CRAFTN CRAFT
N CRAFT
Tools Required:
Tools Required:Tools Required:
Tools Required:
Phillips Head Screwdriver
1/4” Allen Wrench
5/32” Drill Bit
Note:
Note:Note:
Note: Sight-Line Tables use different width Bases for the narrow end
versus the middle and wide end of the table. Shorter Tables (i.e. 120”
and 144”) omit the Center Base.
1. End Base Installation: Loosen (Do not remove) 5/16” Cap Screws
attached to Clamp Bars (See Figure 1)
2. Slide Main Beams into position with the Clamp Bars aligned in
the slots of the Main Beam
(See Figures 1 & 2)
Note:
Note: Note:
Note: For sightline
For sightline For sightline
For sightline with
with with
with center
centercenter
center column base
column base column base
column base only
only only
only
s
ss
shorter be
horter behorter be
horter beams mounted between wider
ams mounted between wider ams mounted between wider
ams mounted between wider bases
basesbases
bases.
..
.
3. Beams should overhang the Base as following;
Note: Dimensions are approximate. Saber allows the Bases
to be positioned where needed for floor core locations,
etc. (See Figure 2)
a. 48” Wide Tables
I. Panel Base = 5”
II. Column Base = 1”
b. 60” Wide Tables
I. Panel Base = 11”
II. Column Base = 7”
4. sing the Allen Wrench, tighten Cap Screws to secure
Bases to the Main Beams
Figure 1
Figure 1Figure 1
Figure 1
Figure 2
Figure 2Figure 2
Figure 2

Saber Collection™Installation Instructions
ID034 – Saber Conference Installation
Revision M – 8/12
Pg. 2 of 2
5. Center Base Installation: For Tables 168” and
longer Slide (2) Main Beams together onto the
Clamp Bars positioning such that the (2) Main
Beams meet in the center of the Base. sing the
Allen Wrench, tighten Cap Screws (See Figure 3)
5a. For Sightline only
For Sightline onlyFor Sightline only
For Sightline only: Tighten locking bolt once all
bases are secured to beams
6. Leveling: Place a Level on the Main Beams to
ensure that the Base structure is level side to side
and end to end. Adjust Glides as necessary to level
the Bases prior to installing the Top
7. Place Top onto the Base and Beam structure. Center
Top using the “L” shape marks on the underside of
the Top as a guide. Pre-drill 5/32 x 3/4” deep holes
corresponding to the Top Attachment Brackets.
Attach Base and Beam structure to Top using olive
colored #12 x 1” Wood Screws provided (See
Figure 4)
8. Base Panels: The Base Panels are designed to bend into
place. Place one side of the Panel into Panel Retention Rail
and flex Panel positioning the opposite side into the
opposite rail. Make sure shorter Panel is on the inside and
the taller Panel is on the outside. The curved end should be
oriented towards the floor to allow wire passage if needed
(See Figures 4 & 5)
Figure 3
Figure 3Figure 3
Figure 3
Figure 5
Figure 5Figure 5
Figure 5
Figure
Figure Figure
Figure
4
44
4