NXP Semiconductors FRDM-K32L2B3 User manual

QUICK START GUIDE
FREEDOM DEVELOPMENT PLATFORM
FRDM-K32L2B3

2
GET TO KNOW THE FRDM-K32L2B3
Figure 1: FRDM-K32L2B3 Callouts Figure 2: FRDM-K32L2B3 Pin-Outs
J14J14
K20 JTAGK20 JTAG
HeaderHeader
U13U13
Accelerometer/Accelerometer/
MagnetometerMagnetometer
(DNP)(DNP)
J3 HeaderJ3 Header
J4 HeaderJ4 Header
DS1 sLCDDS1 sLCD
SW3SW3
J11 K32L2B3J11 K32L2B3
SWD HeaderSWD Header
J2 HeaderJ2 Header
J1 HeaderJ1 Header
Green LEDGreen LED
Red LEDRed LED
SW1SW1
J13 Power/J13 Power/
OpenSDAOpenSDA
Micro USBMicro USB
SW2SW2
ResetReset
ButtonButton
J10J10
K32L2B3K32L2B3
Micro USBMicro USB
2-PTA132-PTA13
4-PTD24-PTD2
6-PTD46-PTD4
8-PTD68-PTD6
10-PTD710-PTD7
12-PTD512-PTD5
14-GND14-GND
16-AREF16-AREF
18-PTE018-PTE0
20-PTE120-PTE1
NC-1NC-1
NC-3NC-3
NC-5NC-5
NC-7NC-7
NC-9NC-9
NC-11NC-11
NC-13NC-13
NC-15NC-15
PTB17-17PTB17-17
PTB16-19PTB16-19
2-PTA12-PTA1
4-PTA24-PTA2
6-PTD36-PTD3
8-PTA128-PTA12
10-PTA410-PTA4
12-PTA512-PTA5
14-PTE2914-PTE29
16-PTE3016-PTE30 15-NC15-NC
13-NC13-NC
11-NC11-NC
9-NC9-NC
7-NC7-NC
5-NC5-NC
3-NC3-NC
1-NC1-NC
11-PTE3011-PTE30
9-PTE09-PTE0
7-PTE237-PTE23
5-PTE225-PTE22
3-PTE213-PTE21
1-PTE201-PTE20
PTB18-1PTB18-1
PTB19-3PTB19-3
PTC0-5PTC0-5
PTC4-7PTC4-7
PTC6-9PTC6-9
PTC7-11PTC7-11
NC-13NC-13
PTC5-15PTC5-15 5V_VIN-165V_VIN-16
GND-14GND-14
GND-12GND-12
P5V-10P5V-10
P3V3-8P3V3-8
RST-6RST-6
P3V3-4P3V3-4
PTD5-2PTD5-2
PTC1-12PTC1-12
PTC2-10PTC2-10
PTB3-8PTB3-8
PTB2-6PTB2-6
PTB1-4PTB1-4
PTB0-2PTB0-2

QUICK START GUIDE FRDM-K32L2B3
3
HOW TO GET STARTED
1. Connect the FRDM-K32L2B3 development board to a PC using the included micro-
USB cable to the Power/OpenSDA Micro USB connector (J13).
2. When the board is powered up, a green LED (D8) will illuminate, indicating 3.3V is
on. Notice that Boot ROM code is executed first out of reset, a time of about three
seconds are consumed by ROM bootloader to check the active communication port
before application code is executed.
3. The FRDM-K32L2B3 board comes preprogrammed with a demo that will initiate the
LED on the board to flash periodically when plugged in.
4. J10 is the USB connector of K32L2B3 on chip USB module.
5. J14 is the K20 JTAG header for OpenSDA firmware update.
6. J11 is the SWD header for K32L2B3.
7. Explore more out-of-box demos and download software and tools at
www.nxp.com/FRDM-K32L2B3.

SUPPORT
Visit www.nxp.com/support for a list of phone numbers within your region.
WARRANTY
Visit www.nxp.com/warranty for complete warranty information.
www.nxp.com
NXP and the NXP logo are trademarks of NXP B.V. All other product or service names are the property of their
respective owners. © 2021 NXP B.V.
Document Number: FRDMK32L2B3QSG REV 1
Agile Number: 926-46355 REV B
GET STARTED
Download installation software
and documentation under
“Jump Start Your Design” at
www.nxp.com/FRDM-K32L2B3