OAKWORKS Clinician Premiere User manual

INSTRUCTION MANUAL
Clinician
Premiere
www.oakworks.com · 717.235.6807
Electric Salon Top
Shown with optional
Adjustable Side Arm Rests
and Universal Table Extender
Flat Top
Shown with optional
QuickLock™ Face Rest and
Boiance™ Crescent and
Hot Towel Cabi

TAB TEXT HERE
© 2012 Oakworks®, Inc.
All rights are reserved. No part
of this document may be
photocopied, reproduced or
translated to another language
without prior written consent
of Oakworks®, Inc.
Oakworks®is a registered
trademark of Oakworks®, Inc.
Notice
The information contained in this
document is subject to change
without notice and should not
be construed as a commitment by
Oakworks®, Inc.
Oakworks®, Inc. assumes no
responsibility for any errors that
may appear in this document nor
does it make expressed or implied
warranty of any kind with regard
to this material, including, but not
limited to, the implied warranties
of merchantability and fitness for
a particular purpose.
Oakworks®, Inc. shall not be liable
for incidental or consequential
damages in connection with or
arising out of the furnishing,
performance, or use of this
document and the program
material which it describes.

TABLE OF CONTENTS
Symbol Identification ................................................................................................ ii
Warnings & Safety Instructions .................................................................................iii
Grounding Instructions .............................................................................................. v
Section I: Product Description
Premiere™ Table Photo & Specifications ................................................. 1
Section II: Installation
Leveling Instructions ................................................................................ 2
Section III: Directions for Use
Daily Cycling For Continued Quiet Operation ....................................... 3
Foot Control .............................................................................................. 3
Table Key Switch ...................................................................................... 4
Under-Table Cabinet ............................................................................. 4-6
Side Arm Rests .......................................................................................... 7
Accessory Option: QuickLock™Face Rest ........................................... 8-9
Accessory Option: Table Extender ..........................................................10
Moving the Premiere™ ............................................................................10
Section IV: Troubleshooting
If Table will not change height or position ............................................11
If Table is making a noise during height adjustment.............................11
Section V: Care & Cleaning .................................................................................12
Section VI: Product Identification .....................................................................13
Section VII: Table Specifications...........................................................................14
Section VIII: List of Parts ........................................................................................15
Section IX: Warranty ...................................................................................... 16
Contact Information ................................................................................ back cover
i
TABLE OF CONTENTS

SYMBOL IDENTIFICATION
ii
SYMBOL IDENTIFICATION
SYMBOL IDENTIFICATION
This symbol, when used in documentation on this product, represents a cau-
tion. Be sure to read and comply with all precautions and warnings.
This symbol, when used in documentation on this product, indicates danger
and warns against an electrical shock hazard. Be sure to observe and
comply with all warnings and instructions.
This symbol, when used in documentation on this product, indicates a
Protective Earth (Ground) Terminal.
This symbol when used in documentation on this product, warns that dur-
ing transport there should be no stacking of containers.
This symbol, when used in documentation on this product, indicates that
the product should be protected from moisture. The humidity specifications
for Transport & Storage are listed on page 18.
This symbol, when used in documentation on this product indicates that
information is given regarding the recommended temperature limits
during transport and storing. The specifications for these limits are listed
on page 18.
This symbol, when used in documentation on this product, indicates the
date of manufacture of the device.
This symbol, when used in documentation on this product indicates
alternating current (AC).
This symbol, when used in documentation on this product, indicates direct
current (DC).
This symbol, when used in documentation on this product, indicates
that instructional information is included. All instructions should be
read carefully and completely before using the equipment.
~
----

WARNINGS & SAFETY INSTRUCTIONS
Improper use of this device can cause injury. Be sure to read all
operating instructions prior to use to prevent injury to operator or client.
Electrical Shock Hazard. To reduce the risk of electric shock, always
disconnect the table from the electrical outlet before moving the table
or doing any maintenance or troubleshooting procedures. Never use
this equipment if it has a damaged cord or plug. Use this equipment
only for its intended use as described in these instructions. Do not use
any attachment or accessories not recommended by the manufacturer.
To reduce the risk of burns, fire, electrical shock or injury:
 •The power supply/control module is located under the top and beneath
the base. Refer servicing to qualified personnel and follow manual
instructions when doing any authorized troubleshooting. Before doing
any work on the unit, disconnect the power cord from the power outlet.
 •Beforecleaningwithanyliquidcleanerbesuretoun-plugthepowercord
from the power outlet. Do not operate the table in standing water.
 •Beforemovingthetable,disconnectthepowercordfromthepoweroutlet
and secure the electrical cord, hand control and foot control out of the
way for moving.
 •RiskofElectricalShock.–Connectthistabletoaproperlygroundedoutlet
only. See Grounding Instructions.
 •Usethisfurnishingonlyforitsintendeduseasdescribedinthese
instructions. Do not use attachments not recommended by the manufacturer.
 •Neveroperatethistableifithasadamagedcordorplug,ifitisnotworking
properly, if it has been dropped or damaged, or dropped into water. Return
the table to a service center for examination and repair.
 •Keepthecordawayfromheatedsurfaces.
 •Donotuseoutdoors.
 •Donotoperatewhereaerosol(spray)productsarebeingusedorwhere 
oxygen is being administered.
 •Maximumshelfloadweight:200lbs.(91kg.)
RiskofInjury–Childrenshouldneverbenearthetablewheninuse.Thistable
must be locked out (use key lock) and controls stored out of reach if there is any
possibility that children would be near the table when not in use.
Never drop or insert any object into any opening.
iii
WARNINGS & IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
DANGER
READ AND
SAVE THESE
INSTRUCTIONS
WARNINGS

WARNINGS & SAFETY INSTRUCTIONS
iv
WARNINGS & IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS(CONT.)
This product is equipped with an interior accessory outlet. The total
electrical load of equipment plugged into this set of outlets is not to
exceed 750 watts.
Close supervision is necessary when this furnishing is used by, or near,
children, invalids or disabled persons. DO NOT leave children alone or allow
them to operate the controls. Keep controls out of reach of children. DO NOT
allow children to crawl into the cabinet or under the table.
To remove the accessories from the cabinet: Turn the accessory controls to the
‘off’ position and then disconnect the unit from the interior power source
by removing the plug from the outlet.
When moving the table: Turn the accessory controls to the ‘off’ position,
disconnect the table from the exterior power source by removing the table
plug from the outlet.
Be certain that the table is completely lowered without any tilt being
present prior to discharging an ambulatory patient. The patient may
lose balance and fall. Do not leave clients unattended when table is set at
its highest level.
The table weighs as much as 200 lbs. DO NOT lift or move the unit
without using proper safely procedures or equipment. DO NOT turn
the Premiere™on its side for any reason. To do so could cause damage
to the base and will void the warranty. There are no serviceable items that
require this action. Never lift the table by grasping the table top as the
table top is not designed to hold the weight of the base and you could
damage the table.
When operating the Premiere™controls and making any and all
adjustments to the table, move hands and feet away from the working
mechanism of the table.
DO NOT sit on the Arm Rests, the elevated Back Rest or Leg Rest. DO NOT
place excess weight on the Side Arm Rests. DO NOT use them in assisting
the client on and off the Premiere™.
DO NOT put excessive weight or pressure on the QuickLock™Face Rest.
Excessive pressure can cause premature failure of the QuickLock™Face
Rest. Do Not extend the dowels of the Face Rest further than 3” from the
table edge to ensure a stable connection.
DO NOT use the hand control and the foot control simultaneously as this
can cause damage to one or both units.
READ AND
SAVE THESE
INSTRUCTIONS
WARNINGS
CAUTIONS

WARNINGS & SAFETY INSTRUCTIONS
v
WARNINGS & IMPORTANT SAFETY INSTRUCTIONS
GROUNDING
INSTRUCTIONS
This product must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electrical current to reduce
the risk of electric shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances. See U.S. sample below.
This product is manufactured for use on a nominal 120-volt circuit for the
United States and a nominal 220-volt circuit for use in Europe. The plug has
a grounding pin in a pattern that varies by country as shown in the Product
Identification section of this manual. Make sure that the product is connected
to an outlet having the same configuration as the plug.
DO NOT store or place anything on the cabinet hood under the Back Rest as
this can cause damage to top and/or hood and will void the warranty.
Maximum Working Load Rating (client and accessories): 500 lbs. (227 kg.)
Plug table into an outlet that is surge protected to a level of 750J or higher.
Failure to do this may void all or part of the warranty.
Correct Implementation Incorrect Implementation
READ AND
SAVE THESE
INSTRUCTIONS
READ AND
SAVE THESE
INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS(CONT.)
DANGER-Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified electrician
or service man if you are in doubt as to whether the product is properly
grounded. Do not modify the plug provided with the product - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician.
To reduce the risk of electric shock, this furnishing has a polarized plug
(one blade is wider than the other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
No adapter should be used with this product.
CAUTIONS
WARNINGS

PRODUCT DESCRIPTION
1
PRODUCT DESCRIPTION
TABLE SPECS* :
• Height *: 25” - 35”
• Width: 29” or 31”
• Length: 73”
• Lift Capacity: 500 lbs Maximum Working Load
• Weight**: 157-182 lbs. (depends on model)
• Top: Electric Salon or Flat top
• Electronics: 1 Multi-Function Foot Control
• Padding: 4” AeroCel™ or 6” AeroCel™
• Upholstery: TerraTouch™ or Ultratouch™
• Cabinetry: Wood/Maple
For electrical specs, see Specifications Chart
* measurements are determined from floor to top of seat pad using
standard padding; these measurements can be affected by natural
material variations in padding
** published weight may differ due to options chosen, natural
material variations and padding density
Self Adjusting
Removable
Arm Rests (2)
(optional)
Sliding Cabinet doors
(access both sides)
Fully Enclosed
Cabinet Base
Accessory
Outlets (2)
Vertical
Hydraulic
Lift Columns (4)
Foot
Control (1)
Premiere™
Universal
Table Extender
(optional)
Table shown here with
optional Golden Oak stain
and Signature One Piece
Leaf Pattern Acrylic Doors.
• Width: 29” or 31”
• Lift Capacity: 500 lbs Maximum Working Load
Flat Top model
shown here with
optional hot towel
cabi ready end
panel. (Must be ordered
at time of table purchase)
Also shown with
QuickLock™Face
Rest and Boiance™
Crescent

INSTALLATION
2
INSTALLATION - LEVELING INSTRUCTIONS
The Premiere™ comes completely assembled and ready to use. Plug the
cord into a functioning outlet that is rated for the table.
Arrange the power cord and control cords so that they will not create a trip-
ping hazard. Place the controls in a safe location where they are convenient
and accessible. Keep the controls out of the way of all table mechanisms.
LEVELING INSTRUCTIONS:
If Table Will Not Sit Flat on the Floor:
The Premiere™is equipped with Leveler Feet that adjust to level the table on
uneven floors. To adjust the Leveler Feet to suit common floor differences
you will need to use a 1 /2” open-end wrench or an adjustable wrench. Adjust
each leg individually in turn by adjusting the height of each leveler foot until
the unit rests level and steady. This adjustment will not effect the function of
the table. The feet can be adjusted out ¼”.
The table weighs as much
as 200 lbs. DO NOT lift or
move the unit without using
proper safely procedures
or equipment. DO NOT turn
the Premiere™on its side for
any reason. To do so could
cause damage to the base
and will void the warranty.
There are no serviceable
items that require this action.
Never lift the table by grasp-
ing the table top as the
table top is not designed to
hold the weight of the base
and you could damage the
table.
When operating the
Premiere™ controls be
sure to observe all cautions
and warnings given in the
manual to prevent injury to
both operator and client.
CAUTION
Use 1/2” Open-end
Wrench to adjust
Leveler Foot
INSTALLATION INSTRUCTIONS:

DIRECTIONS FOR USE
3
DIRECTIONS FOR USE
FOOT CONTROL:
The Oakworks®Premiere™comes complete with a multifunctional foot
control that operates the backrest and leg rest positioning functions as
well as the height. The lifting motor is equipped with a thermal
overload limiter. It has a 10% duty cycle, 2 minutes operating and
18 minutes off.
When operating the
Premiere™controls and making
any and all adjustments to the
table, move hands, feet and
controls away from any work-
ing mechanisms of the table.
Children must be supervised
when around this equipment
by a responsible adult. Do not
leave children alone or allow
them to operate the controls.
Do not allow children to crawl
into the cabinet or under the
table.
Press and hold the appropriate button until the position desired is
achieved and then release. The arm rests (available on Salon Top) will
adjust automatically to provide the most in comfort and ergonomics
while staying parallel to the floor, no matter what the position.
CAUTION DAILY CYCLING
The Oakworks®Premiere™uses hydraulics and hydraulic fluids to adjust
the table height. Maintaining the quiet operation of your table requires
that you fully cycle your table (up & down) twice per day. Cycling of
the table will maintain the lubrication within the hydraulic cylinders for
continued smooth and quiet operation. When not possible, we recom-
mend that you cycle the table (up & down) four times at least once per
week.
1
Backrest UP
Backrest
DOWN
Legrest UP
Legrest
DOWN
2
High Range
Low Range
4
5
3
6
If you have the flat top model,
your table will be equipped
with a two button foot switch
to raise and lower the table.

DIRECTIONS FOR USE
4
DIRECTIONS FOR USE
To Access the Storage in the Under Table Cabinet:
The Premiere™has a fully integrated wood cabinet and base. The large
under-table cabinet provides storage for stacks of towels and other
equipment without interfering with the lift capacity of the table.
There are two (2) sliding doors on both sides of the table. The doors
slide all the way open. The doors on the under-table cabinet are placed
in a slide track for ease of movement. The doors, two (2) on each side,
slide independently along this track with slight pressure on the handles.
The cabinet hood area under the backrest top is not designed for storage or
as an area to hold accessories while with a client. DO NOT use this area
for holding anything. Damage can occur to the table, especially when
commands that are accessed by the foot or hand control are activated.
Placing anything on this area will prohibit movement of the backrest and
can cause damage to the table or the object and will void the warranty.
DO NOT store or place
anything on the cabinet hood
under the backrest as this can
cause damage to the top
and/or hood.
IMPORTANT SAFETY NOTE
Use care when opening
the doors all the way so
that you do not pinch or
injure your fingers.
not FoR StoRAge!
Track
UNDER-TABLE CABINET
CAUTION
CAUTION
TABLE KEYSWITCH
A table keyswitch is located
inside the cabinet on the shelf at
the head end of the table. This
key switch will lock-out the
table and prevent all motions.
It should be used to prevent
unauthorized use. Remove the
key if children have the
opportunity to access the table
without adult supervision.
Track
shown with optional
hand control

DANGER
DIRECTIONS FOR USE
5
DIRECTIONS FOR USE
To Access the Storage in the Under Table Cabinet: (cont)
The cabinet doors will open until they meet the other side of the cabinet
and stop. Slide the door shut to open the other side.
The Premiere™ offers an in-cabinet power strip to accommodate electric
hot towel warmer or other electric devices. This allows you to store the
unit inside with no excess cords to get in the way. With it plugged in,
your towels stay warm and within easy reach, yet are still out of the way.
You will find the plug inside the cabinet at the foot end of the Premiere™.
To access the interior plug and insert the Hot Towel cabi
at head end of table:
The Premiere™ has a removable panel at the head end of the cabinet
to allow the placement of an electric hot towel warmer or other electric
devices inside the cabinet. Before any work is started, unplug the
power cord from the receptacle. To remove this panel unscrew and
remove the 4 screws from the panel retaining strips found on both sides
of the head end of the interior of the cabinet. Once these screws are
removed, push the bottom of the panel inside the cabinet and then
angle the panel to remove it from the opening. Place the screws and
the panel in storage in case of future need to reinstall the panel.
To re-install the panel, unplug and remove any appliances from the
cabinet, angle the panel into the opening and fit the panel into place.
Position the screws into the retaining strips and tighten. Do not over-
tighten the screws.
Screws
found inside
cabinet
holding
retaining strips
UNDER-TABLE CABINET (CONTINUED)
This product is equipped
with an interior 120-volt 60Hz
accessory outlet. Disconnect
all power cords from the
interior power outlet (found
within the cabinet) after
use. The total electrical load
of equipment plugged into
this set of outlets is not to
exceed 1000 watts.

DIRECTIONS FOR USE
6
DIRECTIONS FOR USE
Plug in the towel warmer and slide it inside being careful to move any excess
cord inside the wooden cabinet.
To access the interior plug for use with optional accessory appliances:
For the times when an optional electrical appliance such as a facial
massager is used the Premiere™ comes equipped with an opening to allow
the cord of the appliance to pass through the cabinet and access the
interior outlet, thus giving you complete power without the safety hazard
and distraction of loose cords in the working area.
UNDER-TABLE CABINET (cont)
Note: Appearance of outlets will
vary depending on country of use.

DIRECTIONS FOR USE
7
DIRECTIONS FOR USE
OPTIONAL ACCESSORY
AVAILABLE ON SALON TOP ONLY
Manicure Arm RestsAdjustable Side Arm Rests
1. Insert end of arm rest into
hole in backrest while holding
arm rest at 60° angle.
2. Push end all the way into hole and drop arm rest into horizontal
position. Tug slightly to make sure the armrest is fully locked to
the table (for patient safety).
To remove the arm rest, simply reverse the procedure above.
TO INSTALL THE ARM REST:
The arm rests adjust automatically as the table’s back support moves to remain parallel to the floor in any position.
They are designed to be strong and will take a reasonable amount of weight, but they are not designed to be used to
sustain a person’s weight when getting on or off the table.
CAUTION: Do not use the arm rest
for customer weight support during the
mounting or dismounting of the table.
The arm rest is not designed to support
the patient’s weight.
The arm rest height is adjusted to level at the factory. When in use, some of the new
parts will wear, and you may see some sagging of the arm rest over time. If the arm
rest is too low the height can easily be adjusted using the enclosed Allen wrench.
1. Loosen bottom 2 set screws
(turn counter-clockwise).
2. Turn side set screw in (clock-
wise) while lightly raising the arm
rest with your other hand (to make
the adjustment easier).
3. When you have achieved the desired
height, tighten the two bottom set screws
(turn clockwise).
1. Loosen bottom 2 set screws
(turn counter-clockwise).
2. Turn side set screw out (turn
counter-clockwise).
3. When you have achieved the desired
height, tighten the two bottom set screws
(turn clockwise).
To Raise the Arm Rest
To Lower the Arm Rest
TO LEVEL THE ARM REST:
ARM REST INSTALLATION AND ADJUSTMENT INSTRUCTIONS

DIRECTIONS FOP USE
DIRECTIONS FOR USE
8
QuickLock™FACE REST: * U.S. Patent #5,177,823
Do not put excessive weight
or pressure on the face rest.
Excessive pressure can cause
premature failure of the
QuickLock™Face Rest.
Double articulating action provides nearly limitless positioning options
with the QuickLock™Face Rest. The adjustable pad takes pressure off
sensitive facial areas while providing superb support. The QuickLock™
Face Rest can be used in both prone and supine positioning and folds
out of the way when not in use. Adjustments are made easily by loosen-
ing the cam locks, adjusting for height and angle and then locking the
cam locks into that position. The Premiere™has outlets at the head of the
table for a variety of uses and outlets at the other end that work as well
for additional procedures.
Attaching the QuickLock™ Face Rest / Head & Foot End Outlets:
When attaching the QuickLock™Face Rest to the head or foot end by
using the provided outlets, just slide the frame dowels into the outlets
being sure to keep the 1st cam lock within 3” of the table to ensure a stable
connection.
To remove the QuickLock™Face Rest, just pull the frame from the outlet
until it comes free. Set it safely aside or store it inside the under-table
cabinet until needed.
3”
QuickLock™Face Rest Important Safety Note: Maximum
Distance from edge of table = 3”
Important Safety Note: Maximum
Distance from edge of table = 3”
outlets
CAUTION

DIRECTIONS FOR USE
9
DIRECTIONS FOR USE
Tips for Great Positioning using the QuickLock™ Face Rest:
 • Tousethefacerestwithyourclientsupine,rotatethefacerest
pad so that the thick part of the pad supports your client’s cervical
region. Adjusting the height and angle of the face rest gives your
client perfectly comfortable support.
 • The face pad is flexible so that you can bring the open ends together
or spread them apart to achieve the most comfortable support for
any size face. To avoid your client’s chin from hitting the spacebar,
make sure the pad is narrow enough to support the whole face.
 • Forappropriatecervicalflexion,usethecamlockstoadjustthe
downward angle of the face rest, making sure that the surface of
the face rest pad at the chin is not lower than the surface of the table.
Do not put excessive weight
or pressure on the face rest.
Excessive pressure can cause
premature failure of the
QuickLock™Face Rest
CAUTION
QuickLock™FACE REST (CONTINUED):

ACCESSORY OPTIONS
10
The optional stationary Table Extender provides ultimate comfort for
your tallest clients, quickly and easily. The Table Extender comes with
two connecting arms that slide into the outlets at the foot end of the
tabletop. Slide these fully into the outlets so the Table Extender is flush
to the end of the table top. This Stationary Extender provides 11” of
additional comfort and support when needed.
The Premiere™weighs approximately 200 lbs. You will need 4 people
working together if it is necessary to move the table. Never lift the table
by grasping the table top as the table top is not designed to hold the
weight of the base and you could damage the table and the electronics
that run the tabletop.
If you need to move the table, place one person at each corner of the
table. We recommend that you have the table top in a flex position(with
Arm Rests removed) to have the table top ends out of the way as much
as possible. Have each person firmly grasp the cabinet base at the bottom
by the table legs and lift the table from the base. As when moving any
piece of heavy equipment, bend at the knee and lift with your legs
beneath you and not with your back. Be aware and use proper, safe
procedures for moving a table of this size to prevent injury to yourself
or the table. We strongly recommend that a flatbed dolly be used that
can hold the entire table if moving the table involves any distance.
Before moving the
Premiere™, disconnect the
power cord from the power
outlet and secure the elec-
trical cord, hand control and
foot controls for moving.
The table weighs as much
as 200 lbs. DO NOT lift or
move the unit without using
proper safety procedures
or equipment. DO NOT turn
the Premiere™ on its side for
any reason. To do so could
cause damage to the base
and will void the warranty.
There are no serviceable
items that require this action.
Never lift the table by grasp-
ing the table top as the
table top is not designed to
hold the weight of the base
and you could damage the
table.
Outlets
Moving the Premiere™:
Position 8 at low height range
Grasp
at base
corner
Do not put excessive weight
or pressure on the extender.
Excessive pressure can cause
premature failure of the Table
Extender.
CAUTION
CAUTION
DIRECTIONS FOR USE
Table Extender

TROUBLESHOOTING
IF THE TABLE WILL NOT CHANGE HEIGHT OR POSITION
•Check that the keyswitch inside the table is in the “on” position.
•Check the outlet to be sure that it has power and that the power
cable is plugged in. Try all Foot Control Buttons to see if any work. If
any work, then possibly there is a loose connection or a faulty control-
ler.
•Unplug the power cable from the wall outlet.
•Make sure that all male and female connectors are firmly pushed
into each other. Even a slight misconnection can cause a possible
malfunction.
•Plug the unit back into the wall and check the controls
again. If one or more of the controls still do not work, contact
Customer Service at 800-558-8850 to arrange replacement.
The table weighs as much
as 200 lbs. DO NOT lift or
move the unit without using
proper safety procedures
or equipment. DO NOT turn
the Premiere™ on its side for
any reason. To do so could
cause damage to the base
and will void the warranty.
There are no serviceable
items that require this action.
Never lift the table by grasp-
ing the table top as the
table top is not designed to
hold the weight of the base
and you could damage the
table.
Before doing any work on the
unit, disconnect the power
cord from the power outlet.
Be sure to read all
cautions, warnings
and instructions given
in the manual to prevent
injury to both operator
and client.
11
TROUBLESHOOTING
CAUTION
IF THE TABLE IS MAKING NOISE DURING HEIGHT ADJUSTMENT
•If you hear squealing or a pop during the height adjustment, this
may be related to lack of lubrication in the hydraulic cylinders. We
recommend that you immediately cycle the table fully up/down at
least four times. If this does not work, then let the motor cool down
for at least 30 minutes and repeat the procedure. The table should
return to its normal quiet mode. Refer to “DIRECTIONS FOR USE;
Important for continued quiet operation.”

CARE & CLEANING
12
CARE & CLEANING
Before cleaning with any
liquid cleaner be sure to un-
plug the power cord from the
power outlet. Do not operate
the table in standing water.
UPHOLSTERY
In order to maintain your product’s quality and ensure the life of your upholstery, we
have tested several preventative steps you can take to protect the upholstery fabric on
your table and accessories.
Here are a few suggestions in caring for your upholstery fabric:
• DO NOT store your table or upholstery fabric-covered accessories in temperatures
below 32°F/0°C or above 95°F/35°C. Extreme hot and cold temperatures will
damage the upholstery fabric. Some potential results are cold-cracking, brittleness
and upholstery fabric stretching. And, always keep your table away from heaters,
electrical appliances and direct sunlight.
• We recommend cleaning your upholstery fabric to protect it against oil stains and
dirt which will cause cracking and permanent stains over time. Clean your uphol-
stered items when needed using a mild solution of 4:1 diluted non-alcohol cleaner
such as Formula 409®, Fantastik®, Green Windex®or some other non-abrasive
cleaner. For disinfecting purposes you may use Protex, MadaCide, Accell TB,
Virox®(Canada) or a diluted 1/100 bleach solution. Dry the table immediately after
cleaning to remove excess cleaning solution. Using citrus based cleaners or other
strong cleaners, such as alcohol, acetone, higher concentrations of bleach or other
products that contain high concentrations of these substances, can shorten the life
of your fabric, or discolor it. Note: Damage caused by cleaners will not be covered
under the warranty.
• Use both ends of the table evenly. Occasionally switch the face rest from one end
of the table to the other to reduce uneven wear.
• Protect your table and accessories with sheets and fleeces. We offer both fitted
sheets and thick fleeces that protect your upholstery fabric against oil stains while
offering comfortable softness to your clients. You can also preserve your face rest
and bolsters with covers and fleeces.
• Use only a mild solution of 4:1 diluted non-alcohol cleaner such as 409®, Fantastik®
or some other non-abrasive cleaner to wipe down the metal and wooden surfaces.
Apply with a damp (not wet) lint-free cloth. Be sure excess liquid does not drip
onto, or into, any of the electrical controls or mechanisms. Be sure that the unit is
unplugged before cleaning these areas. Wipe these areas dry carefully with a lint free
cloth.
• Electronic and/or manual lift mechanisms require no general maintenance or
lubrication. Hydraulic units may require yearly maintenance.
• If the table will be out of use for an extended period of time, the power cord
should be unplugged from the receptacle. To prevent inadvertent damage to the
plug or cord, the cable should be coiled and secured with a wire tie or rubber band.
• The wooden cabinetry of the equipment can be polished with any polish approved
for wooden surfaces. Spray, or pour the polish onto a soft cloth and be careful not
to get it onto other surfaces.
• It is important to visually inspect your table on a quarterly basis to ensure all
components are working properly and safely. Be sure to tighten all bolts to be sure
they are secure. Over time they may work their way loose, leading to an unsafe
condition.
•
• Thefacerestandtableextendershouldberemovedwhennotinuse.
These items should be stored in a cool, dry place.
BASE & CONTROLS
ACCESSORIES
WARNINGS

PRODUCT IDENTIFICATION
13
PRODUCT IDENTIFICATION
POWER LEAD PLUGS
Oakworks® Part #: Voltage (ACE) Power Cord Plug
7791 120v 60 Hz 3 prong grounded
North America
7791-03 220v 50 Hz Continental Plug;
Europe/Italy
7791-04 220v 50 Hz Swiss plug; Switzerland
7791-02 220v 50 Hz British plug;
United Kingdom
7791-06 220v 50 Hz Australian Plug; Australia