OAKWORKS PROLUXE convertible User manual

INSTRUCTION MANUAL
www.oakworks.com · 717.235.6807
your portable table converted to a lift table and back again
convert i second! ...the bac t  portabl!
PROLUXE™convertible

© Copyright 2011
Oakworks® , Inc.
Manual Part # MMMNST0022
1st Edition, January 2011
Printed in U.S.A.
All rights are reserved. No part
of this document may be
photocopied, reproduced or
translated to another language
without prior written consent
of Oakworks®, Inc.
Oakworks® is a registered
trademark of Oakworks®, Inc.
Notice
The information contained in this
document is subject to change
without notice and should not
be construed as a commitment by
Oakworks®, Inc.
Oakworks®, Inc. assumes no
responsibility for any errors that
may appear in this document nor
does it make expressed or implied
warranty of any kind with regard
to this material, including, but not
limited to, the implied warranties
of merchantability and fitness for
a particular purpose.
Oakworks®, Inc. shall not be liable
for incidental or consequential
damages in connection with or
arising out of the furnishing,
performance, or use of this
document and the program
material which it describes.

TABLE OF CONTENTS
TABLE OF CONTENTS
TABLE OF CONTENTS
Symbol Identification .................................................................................. pg 1
Warnings & Cautions .............................................................................pg 1
Grounding Instructions ..........................................................................pg 2
Product Description & Specs ................................................................pg 3
Directions for Use
One time only set up ...........................................................pg 4 - 8
Loading your portable table .............................................. pg 9 - 11
Remove your portable table ................................................... pg. 12
Controls - Foot control & Hand control ................................... pg 13
Using your ProLuxe Convertible ................................................ pg 14
General care of equipment ....................................................................... pg 15
Electrical specifications .............................................................................. pg 15
Power & lead plug ID .................................................................................. pg 16
Contact Information ..................................................................... back cover

1
WARNINGS & CAUTIONS
SYMBOL ID & WARNINGS
SYMBOL IDENTIFICATION - WARNINGS & CAUTIONS
SYMBOL IDENTIFICATION
This symbol, when used in this manual and on product labels, represents a caution
warning. Be sure to read and comply with all precautions and warnings.
This symbol, when used in this manual and on product labels, warns against an electrical
shock hazard. Be sure to observe and comply with all warnings.
This symbol, when used in this manual or on product labels, indicates a Protective
Earth (Ground) Terminal.
This symbol when used in this manual or on product labels, warns that during transport
there should be no stacking of containers.
This symbol, when used in this manual or on product labels, indicates that the product
should be protected from moisture. The humidity specifications for Transport &
Storage are listed in the back of this manual.
This symbol, when used in this manual or on product labels, indicates that information
is given regarding the recommended temperature limits during transport and storing.
This symbol, when used in this manual or on product labels, indicates the date of
manufacture of the device.
This symbol, when used in this manual or on product labels, indicates alternating
current (AC).
This symbol, when used in this manual or on product labels, indicates direct current
(DC).
This symbol, when used in this manual or on product labels, indicates that
instructional information is included. It should be read carefully and completely .
~
----
Improper use of this device can cause injury. Be sure to read all operating instructions
prior to use.
Weight limit is defined by the portable table used with this product. (If the portable
table has a weight limit of 450 lbs, then the system is 450 lbs) up to a maximum of 550 lbs.
Be certain that the table is completely lowered prior to discharging an ambulatory
patient. The patient may lose balance and fall.
Electrical Shock Hazard. The power supply/control module is located below the base
of the table. No user serviceable parts are inside. Refer servicing to qualified personnel.
Before doing any work on the unit or cleaning with any liquid cleaner, unplug wall con-
nector prior to contact with any cables connected to the power supply.
Plug table into an outlet that is surge protected to a level of 750J or higher.
Failure to do this may void all or part of the warranty.
WARNING
CAUTION
WARNING
CAUTION

2
GROUNDING
GROUNDING
GROUNDING
INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical current to reduce
the risk of electric shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances. See U.S. sample below.
This product is manufactured for use on a nominal 120-volt circuit for the
United States and a nominal 220-volt circuit for use in Europe. The plug has
a grounding pin in a pattern that varies by country as shown in the Product
Identification section of this manual. Make sure that the product is connected
to an outlet having the same configuration as the plug.
DANGER-Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified electrician
or service man if you are in doubt as to whether the product is properly
grounded. Do not modify the plug provided with the product - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician.
To reduce the risk of electric shock, this furnishing has a polarized plug
(one blade is wider than the other). This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
No adapter should be used with this product.
CAUTION
GROUNDING INSTRUCTIONS

3
DIRECTIONS FOR USE
DIRECTIONS FOR USE
PRODUCT
DESCRIPTION
wheels (2)
TABLE SPECIFICATIONS
• Height Range: 20” - 36”
• Width: fits portable tables 27” - 33” wide
• Lift Capacity: Weight limit is defined by the portable table
used with this product. (If the portable table
has a weight limit of 450 lbs, then the system is
450 lbs) up to a maximum of 550 lbs.
• Top: works with rectangular, round
corner, or backrest portable tables
• Electronics: 120v or 220v electric motor
(1) low voltage hand control or
(1) low voltage foot control
knobs (4)
Adjustable portable
table supports (2 sets)
Center alignment
groove
Portable table
secure strap
Strap cleat
electric
motor
End bumper of
portable table
support
Hook behind the cleat

4
PREPARE YOUR PROLUXE CONVERTIBLE
PREPARE YOUR PROLUXE CONVERTIBLE
ONE TIME ONLY PROLUXE CONVERTIBLE SET-UP
STEP 1
Loosen all knobs below the adjustable
portable table supports by turning the
knob counter-clockwise.
STEP 2
Slide the adjustable portable table
supports to their widest position.
STEP 3
Remove the portable table secure
strap from the strap cleat
(if necessary).
STEP 4
Plug in the Convertible and
lower to its lowest height
This is a one time only procedure for each given portable table.

5
PREPARE YOUR PROLUXE CONVERTIBLE
PREPARE YOUR PROLUXE CONVERTIBLE
STEP 5
Open your portable table on its side.
STEP 6
Remove the shiatsu cables or bolts on
one side to enable your table to lay at.
There are different types of shiatsu
cables. Follow the directions below
based on the type you have. Or follow
your table manufacturer’s instructions.
WING NUT
Remove the wing nut
Location of Shiatsu
release bolts or
wing nuts
Remove wood brace Remove cable Replace wood brace
and wing nut
Repeat these steps on both sides of the table. Locations shown above.
C-CLAMP
C-Clamp closed Open C-Clamp Remove Shiatsu
cable
Repeat these steps on both C-Clamps.
Close C-Clamp
CAUTION
Follow your table
manufacturer’s instructions
for using the Shiatsu option
if your table has them.
The instructions shown here
are for general reference
only.
NOTE: Some systems may be slightly different such as; cable not between braces, hex nut
instead of wing nut. You may need to use a wrench to remove the bolt.

6
PREPARE YOUR PROLUXE CONVERTIBLE
STEP 6
With your ProLuxe
Convertible at its lowest
height, stand at the side
where the portable table
supports are towards the
outside, as shown here.
Have the widest side of the adjustable
portable table supports facing you.
A
Lift your portable table onto
the ProLuxe Convertible
base.
B
Open your portable table
so that it is at and position
the bottom away from you.
C
Lower your portable
table onto the ProLuxe
Convertible base.
CAUTION
Be sure to read and follow
the directions on how to
center & secure your
portable table (shown on
page 7) before use.
PREPARE YOUR PROLUXE CONVERTIBLE
STEP 7
Load your portable table

7
PREPARE YOUR PROLUXE CONVERTIBLE
STEP 8
Once your portable table is on the ProLuxe Convertible, you are ready to align &
secure it to the base.
B
Visually center the portable table
with the base of the ProLuxe
Convertible on both ends.
C
Be sure that the knobs are loose so
you can adjust the table supports.
D
Keeping the portable table centered,
push the adjustable table supports
together against the sides of your
portable table.
A
Align the hinge of the portable table
over the center alignment groove.
Hinge of portable table
Center alignment
groove
PREPARE YOUR PROLUXE CONVERTIBLE