Ocean Matrix OMX-HDMI-HDB1X8 User manual

USER MANUAL
OMX-HDMI-HDB1X8
8-port HDMI Splitter Extender over Single Cat5/Cat5e/Cat6
using HDbitT Technology with 8 Receivers
Ocean Matrix
812 Kings Highway ·Saugerties, NY 12477
www.oceanmatrix.com

OMX-HDMI-HDB1X8
8-port HDMI Splitter Extender
The Ocean Matrix OMX-HDMI-HDB1X8 Splitter Extender System over
Single Cat6 distributes 1 HDMI source to 8 HDMI displays simultane-
ously. This system extends high definition audio/video transmission be-
yond the standard distances for HDMI cable limitations via HDbitT tech-
nology. The OMX-HDMI-HDB1X8 delivers full 1080P HDMI signal up to
394feet over a single Cat6 network cable. An IR signal transmission
allows for remote control of the source at a secondary location with IR
extension cables.
Includes
 One Extender Splitter
 Eight Receivers—each receiver includes one IR receiver extension
cable and one 5VDC/1A power adapter
 One IR blaster extension cable, connects to transmitter
 12VDC/3A power adapter
Specifications
Supported Resolutions 480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz,720p@50/60Hz, 1080i@50/60Hz,
1080p@50/60Hz
Transport Protocol HDbitT
Transmission Range Full 1080P HDMI signal up to 394 feet
IR Remote Control Supports 20-60kHz standard IR remote controls
Power Supply TX: 12VDC/3A, RX:5VDC/1A
Power Consumption TX: 24W, RX: 3W
Working Temperature 32°F - 140°F (0℃- 60℃)
Dimensions (LxWxH) TX: 11.77x4.36x1.17in(299x110.7x29.6mm)
RX: 3.81x3.70x0.93in (96.8x94x 23.7mm) per unit
Weight Transmitter 0.95 lb., Receiver 0.31 lb. (142g /430g)
HDMI Signal Compatible with HDCP
Ocean Matrix OMX-HDMI-HDB1X8 Page 2

OMX-HDMI-HDB1X8
Installation Requirements
1. HDMI source device such as a video camera, media player,
monitoring equipment or computer.
2. HDMI display device such as an SDTV, HDTV, or projector with
HDMI port.
3. UTP/STP Cat 5/Cat5e/Cat6 network cable in accordance with the
IEEE-568B wiring standard.
4. Transmission length: Cat5-80m, Cat5e-100m, Cat6-120m.
Installation Safety
1. Identify the receiver and the transmitter in order to make proper
connections during installation.
2. Do not hot swap (plug/unplug) when in operation.
3. Only use included power supplies to reduce risk of damage
or injury.
IR User Guide
1. Plug the IR blaster extension cable into the IR-OUT port
of the Transmitter TX.
2. Plug the IR receiver extension cable into the IR-IN port of the
Receiver RX.
3. Place the emitter of the IR blaster as close as possible to the IR
receiver of the signal source device.
4. Direct the IR remote controller of the signal source device towards
the IR receiver (connected to the RX of HDMI extender), to remote
control the source media playback.
Ocean Matrix OMX-HDMI-HDB1X8 Page 3

1 Reset Button 2 HDMI Signal Input 3 IR Extender Output - connect IR blaster extension cable 4 Signal Link Status Indicator 5 RJ45 Output 6 Power Input
Ocean Matrix OMX-HDMI-HDB1X8 Page 4
OMX-HDMI-HDB1X8
Transmitter
32 6
541

OMX-HDMI-HDB1X8
Receiver
1 Reset Button
2 HDMI Signal Output
3 IR Extender Input - connect IR receiver extension cable
4 5VDC Power Input
5 Power Status Indicator
6 HDbitT Network Input
7 Data Transmission Status Indicator
8 Network Link Status Indicator
7 8654
1 32
Ocean Matrix OMX-HDMI-HDB1X8 Page 5

Installation
Cat6 Network Cable—follow the IEEE-568B wiring standard:
OMX-HDMI-HDB1X8
Ocean Matrix OMX-HDMI-HDB1X8 Page 6
5. Blue/White
6. Green
7. Brown/White
1. Orange/White
2. Orange
3. Green/White
4. Blue

Connection
1. Connect HDMI input with HDMI output of source device
2. Connect IR blaster extension cable to the IR extender out port
3. Connect RJ45 port with RJ45 input port of HDMI extender RX
4. Connect HDMI output of HDMI extender RX to HDMI input of HDTV
and set the source input to the correct HDMI input channel
Troubleshooting
Display shows “Waiting for Connection”
 Ensure power supply is firmly connected.
Display indicates there is a signal loss
 Check all connections.
 Connect the signal source directly to the display device to
ensure there is a signal output. Change the signal source if
necessary.
Degraded video signal
 Check cable lengths between the TX to the switch, the
switch to RX.
 Ensure the connection between each level is within
required ranges.
 Press the RESET button on the TX/RX front panel, reset
and reconnect.
OMX-HDMI-HDB1X8
Ocean Matrix OMX-HDMI-HDB1X8 Page 7

Ocean Matrix
812 Kings Highway
Saugerties NY 12477
www.oceanmatrix.com
SAFETY PRECAUTIONS
1. To prevent fire or shock hazard, do not expose this equipment to high
humidity and/or dust. Do not use in an unprotected outdoor installation
nor any area classified as overly damp or wet.
2. The temperature for installation should be kept between 32°F to 140°F
(0°C to 60°C). Avoid direct sunlight exposure or extreme changes of
temperature over a short period of time.
3. Do not disassemble the unit or place it on an unstable base.
4. Do not drop the unit and avoid heavy impact.
5. This unit should not be permanently installed unless proper ventilation is
provided. Any enclosure openings must not be blocked or covered as
they protect the unit from overheating.
6. Before cleaning, turn off the power and unplug the unit from all
connections. Use a damp cloth. Do not use liquid or aerosol cleaners.
7. Do not overload outlets and extension cords as this may result in a risk of
fire or electric shock.
8. Enclosure entry is dangerous. Never push objects of any kind, including
liquids, into this unit through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock.
9. Do not attempt to open or service this unit yourself as opening orremoving
covers may expose you to dangerous voltage and other hazards.
10. There are no user-serviceable parts inside the unit. If the unit requires
service contact your authorized dealer, or an authorized repair service
company.