OEM Tools 26038 Service manual

WARNING
The following safety information is provided as a guideline to help you operate your Air Blow and Suction Gun under the safest possible
conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not
followed. The following safety instructions are to provide the user with the information necessary for safe use and operation. Please read and
retain these instructions for the continued safe use of your Air Blow and Suction Gun. Failure to follow instructions listed below may result in
serious injury. In addition, make sure that anyone who uses the equipment understands and follows these safety instructions as well.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin
using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues arising from modification. We strongly
recommend that this product is not modified and/or used for any application other than that for which it was designed. If you have any questions relative
to a particular application, DO NOT use the product until you have first contacted customer service to determine if it can or should be performed on the
product.
WARNING:Pursuant to California Proposition 65, this product contains chemicals known to the state of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
Operating Instructions and Parts Manual 26038
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing
all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property.
Please retain instructions for future reference.
1
7/21
2021 OEMTOOLS®
AIR BLOW AND
SUCTION GUN
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
UNPACKING
After unpacking the unit, inspect carefully for any damage that may
have occurred during transit. Check for loose, missing, or damaged
parts. If any damage is observed, a shipping damage claim must be
filed with the carrier. DO NOT use the OEMTOOLS®26038 Air Blow
and Suction Gun if broken, bent, cracked or damaged parts (including
labels) are noted. Any Air Blow and Suction Gun that appears damaged
in any way, operates abnormally or is missing parts should be removed
from service immediately. If you suspect that the Air Blow and Suction
Gun was subjected to shock load (a load that was dropped suddenly,
unexpectedly, etc.) Immediately discontinue use until it has been
checked by a factory authorized service center.

2
Operating Instructions and Parts Manual 26038
7/21
2021 OEMTOOLS®
AIR BLOW AND
SUCTION GUN
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as potential hazards specific
to it.
2. Keep work area clean and well lit. Cluttered or dark work areas
invite accidents.
3. Keep children away. All children should be kept away from the
work area. Never let a child handle a tool without strict adult
supervision.
4. DO NOT operate this tool if under the influence of alcohol or
drugs. Read warning labels on prescriptions to determine if your
judgment or reflexes are impaired while taking drugs. If there is
any doubt, DO NOT attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-
skid safety shoes, hard hat or hearing protection should be used
in appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. DO NOT overreach. Keep proper footing and balance at all times
when operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool
is damaged, it should be carefully inspected to make sure that it
can perform its intended function correctly. If in doubt, the part
should be repaired. Refer all servicing to a qualified technician.
Consult your dealer for advice.
9. Keep away from flammables. DO NOT attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained
persons. Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Properly maintained tools are less likely to bind and are easier
to control. DO NOT use a damaged tool. Tag damaged tools “DO
NOT use” until repaired.
14. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation.
15. If damaged, have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
16. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
17. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified
personnel could result in a risk of injury.
18. When servicing a tool, use only identical replacement parts. Use
of unauthorized parts or failure to follow maintenance instructions
may create a risk of injury.
19. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the
work area free of obstructions, grease, oil, trash, and other debris.
DO NOT use this product in a damp or wet location.
20. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact
OEMTOOLS®for a replacement.
21. Keep the handle dry, clean, and free from brake fluid, oil, and
grease.
22. Before use, read and understand all warnings, safety precautions,
and instructions as outlined in the vehicle manufacturer’s service
manual. It is beyond the scope of this manual to properly describe
the correct procedure and test data for each vehicle.
23. The warnings, precautions, and instructions discussed in this
manual cannot cover all possible conditions and situations that
may occur. The operator must understand that common sense
and caution are factors which cannot be built into this product,
but must be supplied by the operator.
24. We believe the information contained herein to be reliable.
However, general technical information is given by us without
charge and the user shall employ such information at their own
discretion and risk. We assume no responsibility for results or
damages incurred from the use of such information in whole
or in part. Always refer to specific instructions and technical
information supplied by vehicle manufacturer.
25. The manufacturer declines any and all responsibility for damage
to vehicles or components if said damage is the result of
unskillful handling by the operator or of failure to observe the
basic safety rules set forth in the instruction manual.
26. The procedures documented in this manual are to serve as
guidelines for the use of this equipment.
PRODUCT DESCRIPTION
The OEMTOOLS®Air and Blow Suction Gun was developed for quick
and easy clean up, designed with a one touch button that will change
the gun from blow to suction mode.
PRODUCT SPECIFICATIONS
Maximum Air Pressure 90 psig, 6.2 bar
Air Consumption 3.36 CFM
Air Inlet Thread Size 1/4" PT(NPT)
Recommended Hose Size 3/8"
Suction Power 9 cmHg (with dust bag)
Minimum Hose Size 5/16" I.D.
Sound Pressure Level 97 dBA
Vibration 0.4m/s2
Length 5.7"
Weight 0.88 Lb.
CONTENTS
Housing Assembly (1), Deflector (1), Dust Bag (1), Clamp Ring (1),
Extension Tube (1), Flexible Hose Assembly (1), Small Diameter
Vacuum (1), Flat Tube (1), Brush (1)

3
Operating Instructions and Parts Manual 26038
7/21
2021 OEMTOOLS®
AIR BLOW AND
SUCTION GUN
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
WARNING FAILURE TO OBSERVE THESE WARNINGS COULD
RESULT IN INJURY. This instruction manual contains important safety
information. Read this instruction manual carefully and understand all
information before operating this tool.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause
cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
• lead from lead-based paints
• crystalline silica from bricks and cement and other masonry
products
• arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals,
work in a well ventilated area and work with approved safety
equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
WARNINGS
1. Always operate, inspect and maintain this tool in accordance with
American National Standards Institute Safety Code of Portable Air
Tools (ANSIB186.1) and any other applicable safety codes and
regulations.
2. For safety, top performance and maximum durability of parts,
operate this tool at 90 psig; 6.2 bar max air pressure with 5/16"
diameter air supply hose.
3. Always wear impact-resistant eye and face protection when
operating or performing maintenance on this tool. Always wear
hearing protection when using this tool.
4. High sound levels can cause permanent hearing loss. Use
hearing protection as recommended by your employer or OSHA
regulation.
5. Keep the tool in efficient operating condition.
6. Operators and maintenance personnel must be physically able to
handle the bulk, weight and power of this tool.
7. Air under pressure can cause severe injury. Never direct air at
yourself or others. Always turn off the air supply, drain hose of
air pressure and detach tool from air supply before installing,
removing or adjusting any accessory on this tool, or before
performing any maintenance on this tool. Failure to do so could
result in injury. Whip hoses can cause serious injury. Always
check for damaged, frayed or loose hoses and fittings, and
replace immediately. DO NOT use quick detach couplings at tool.
See instructions for correct set-up.
8. Air powered tools can vibrate during use. Vibration, repetitive
motions or uncomfortable positions over extended periods of time
may be harmful to your hands and arms. Discontinue use of tool
if discomfort, tingling feeling or pain occurs. Seek medical advice
before resuming use.
9. Place the tool on the work before starting the tool.
10. DO NOT indulge in any horseplay with this tool.
11. Slipping, tripping and/or falling while operating air tools can be a
major cause of serious injury or death. Be aware of excess hose
left on the walking or work surface.
12. Keep body working stance balanced and firm. DO NOT over reach
when operating the tool.
13. Anticipate and be alert for sudden changes in motion during start
up and operation of any power tool.
14. DO NOT carry tool by the hose. Protect the hose from sharp
objects and heat.
15. Tool shaft may continue to rotate briefly after throttle is released.
Avoid direct contact with accessories during and after use. Gloves
will reduce the risk of cuts or burns.
16. Keep away from rotating end of tool. DO NOT wear jewelry or
loose clothing. Secure long hair. Scalping can occur if hair is not
kept away from tool and accessories. Choking can occur if neck
wear is not kept away from tool and accessories.
17. DO NOT use near flammable material, such as gas tanks.
18. DO NOT vacuum any liquids.
19. Take care that the exhaust air does not point towards any other
person or material or substance that could be contaminated by oil
droplets. When first lubricating a tool or if the tool exhaust has a
high oil content DO NOT allow the exhaust air to come near very
hot surfaces or flames.
20. This tool is not suitable for underwater use or use in explosive
environments.
21. DO NOT lubricate tools with flammable or volatile liquids such as
kerosene, diesel or jet fuel.
22. DO NOT remove any labels. Replace any damaged labels.
23. Use accessories recommended by OEMTOOLS®.
OPERATION INSTRUCTIONS
CAUTION:To operate as a blow gun, remove end cap, remove
and reverse the position of the valve. Always ensure that the o-rings
are replaced properly.
Factors outside the tool may cause loss of power or erratic action.
Reduced compressor output, excessive drain on the air line, moisture
or restrictions in air pipes or the use of hose connections of improper
size or poor condition may reduce air supply. Grit or gum deposits
in the tool may cut power and may be corrected by cleaning the air
strainer and flushing out the tool with gum solvent oil or an equal
mixture of SAE #10 oil and kerosene. If outside conditions are in order
and the tool continues erratic action or low power, disconnect tool
from hose and take tool to your nearest authorized service center.
AIR SUPPLY
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 psi at the
tool while running free. Higher pressure (over 90 psig; 6.2 bar) raises
performance beyond the rated capacity of the tool, which will shorten
tool life because of faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water in
the air line will cause damage to the tool. Drain the air tank daily.
Clean the air inlet filter screen on at least a weekly schedule. The
recommended hookup procedure can be viewed in the below figure.
The air inlet used for connecting air supply has standard 1/4" NPT. Line
pressure should be increased to compensate for unusually long air
hoses (over 25 feet). Minimum hose diameter should be 5/16" I.D. and
fittings should have the same inside dimensions and be tightly secured.
Drain Daily
RegulatorOilerQuick CouplerLeader
Hose
Nipple
Do Not Install
Quick Coupling
Here
Nipple
Filter
Air Supply
Whip Hose

4
Operating Instructions and Parts Manual 26038
7/21
2021 OEMTOOLS®
AIR BLOW AND
SUCTION GUN
Figure Description Qty.
1Housing 1
2O-Ring (AS123) 4
3Valve 1
4End Cap 1
5Trigger 1
6Pin (4*22) 1
7Cap 2
8Regulator Knob 1
9Cover 1
10 O-Ring (P4) 1
11 Valve Seat 1
12 O-Ring (P6) 1
13 Valve Stem 1
14 Spring 1
PRODUCT LAYOUT PARTS LIST
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS®LIMITED LIFETIME WARRANTY
For as long as you own this OEMTOOLS®product, if you find any defect in material or workmanship, through normal usage, return it to the place of purchase or to
OEMTOOLS®for repair or replacement at our discretion. In order to obtain this service, send your tool and proof of purchase (transportation pre-paid) to:
OEMTOOLS®Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our inspection verifies the defect, we will repair or replace the
product, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but
if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will not provide any warranty for products subjected to abnormal
use. Abnormal use includes (but is not limited to) abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,
blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits, files, and batteries as necessary. OEMTOOLS®
reserves the right to make any changes in construction or design at any time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations
outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific
legal rights, and you may also have other rights, which vary from state to state.
Don’t forget to register your new OEMTOOLS®product at www.oem-tools.com.
CONTACT US
Figure Description Qty.
15 Steel Ball (1/8") 1
16 Spring 1
17 Screw (M4*4) 1
18 O-Ring (AS010) 3
19 Ring (ISTW-8) 2
20 Clamping Ring 1
21 Deflector 1
22 Dust Bag 1
23 Extension Tube 1
24 Flat Tube 1
25 Brush 1
26 Small Tube 1
27 Flexible Hose 1
28 O-Ring (SM009) 1
Description Inspection Daily Weekly
Check the condition of air line accessories, and drain out the water from the separators and air line to keep the air
supply system of air line clean and dry.
Always keep the air pressure at 90 psi (6.3kg/cm2) for maximum tool performance and take your reading while the
tool is running.
Use proper couplers, nipples, hoses, pipes and fittings.
Check that quick change couplers are in secure connection and good order.
Keep tools properly lubricated to prevent wear and rust.
Always use safety goggles or a face shield when operating air tools. Never wear loose clothing that might get
caught in the tool and cause injuries.
While installing ship hoses or quick coupler directly into the tool, use a liquid pipe sealant to prevent damage to the
housing from damage. (do not use Teflon tape)
Always use proper wheel and pad for sanding and keep the secure connector in good order
Never use a sander as a grinder. Sanders are intended for sanding only.
Always use accessories with a rated speed equal to or greater than the sander’s speed.
TROUBLESHOOTING