oGrow OGAL-666A User manual
Notes:
1. It takes about 2-3 hours to assemble the greenhouse by 2-3 persons.
2.The UV-protected side of the sheet is covered with opal white film and
must face towards the sun.
3.Remove approximately 2 inches of film from all sheet edges before
installing.Removing all film immediately after the construction is
completed
4.Make sure the greenhouse is located on a flat, level surface.
TO PREVENT INJURY, READ AND UNDERSTAND THE
GREENHOUSE ASSEMBLY INSTRUCTIONS BEFORE USE.
GENERAL SAFETY, WARNINGS AND PRECAUTIONS
KEEP WORK AREA CLEAN AND DRY.
Cluttered, damp or wet work areas invite injuries.
STAY ALERT. Watch what you are doing at all times. Use common
sense. Do not use the greenhouse when you are tired or distracted from
the job at hand. It is recommended to use gloves for assembling the
greenhouse.
MAINTAIN THIS PRODUCT WITH CARE.
Keep the greenhouse clean and dry for better performance:
maintenance should be performed regularly.
USE THE RIGHT PRODUCT FOR THE JOB.
Do not attempt toforce a small product to do the work of a larger
industrial product. There are certain applications for which the
greenhouse was designed. It will do the job better and more safely in the
manner for which it was intended. Do not modify the greenhouse and do
not use the greenhouse for a purpose for which it was not intended.
MAINTAIN A SAFE WORKING ENVIRONMENT.
Keep the work area tidy. Make sure there is adequate surrounding
workspace. Avoid high traffic areas. Always keep the work area free of
obstructions, grease, oil, trash and other debris.
PROPER GREENHOUSE LOCATION.
Make sure the greenhouse is located on a flat, level surface.
TO PREVENT INJURY, PLEASE READ AND UNDERSTAND THE
GREENHOUSE ASSEMBLY INSTRUCTIONS MANUAL BEFORE
USE.
Notes:
1. Around 2-3 hours is needed to assemble the greenhouse by 2-3
individuals.
2. The UV-protected side of the panel sheets is covered with opal
white film and must be placed facing the sun.
3. Before installing the sheets, remove around 2 inches of film from all
the edges. Once the construction is completed, remove the the entire
film immediately.
4. Ensure that the greenhouse is located on a flat and level surface.
GENERAL SAFETY, WARNINGS AND PRECAUTIONS
KEEP WORKING AREA CLEAN AND DRY.
Cluttered, damp or wet working areas invite injuries.
BE ALERT. Always be cautious of your actions. Use your common
sense. Do not assemble the structure if you are tired or distracted.
Use gloves when assembling the greenhouse.
HANDLE THIS PRODUCT WITH CARE
Keep the greenhouse clean and dry to maintain better performance.
Also, regular maintenance must be done.
USE THE SUITABLE TOOLS FOR THE JOB
Do not use small tools in lieu of larger ones. Tools are not suitable for
every type of work. The greenhouse is designed in order to provide
better condition and safety. So, do not perform any modification on
the greenhouse. Do not use it aside from its intended purpose.
MAINTAIN A SAFE WORKING ENVIRONMENT
Keep your working area clean and organized. Make sure that there is
enough space for you to work on. Avoid crowded areas. Also, keep
source of obstruction, grease, oil or trash far from your working zone.
PROPER GREENHOUSE LOCATION
Place the greenhouse on a flat and level surface.
6X6FT
79 inches x 76 inches x 75 inches
OGAL-666A
Notes:
1. It takes about 2-3 hours to assemble the greenhouse by 2-3 persons.
2.The UV-protected side of the sheet is covered with opal white film and
must face towards the sun.
3.Remove approximately 2 inches of film from all sheet edges before
installing.Removing all film immediately after the construction is
completed
4.Make sure the greenhouse is located on a flat, level surface.
TO PREVENT INJURY, READ AND UNDERSTAND THE
GREENHOUSE ASSEMBLY INSTRUCTIONS BEFORE USE.
GENERAL SAFETY, WARNINGS AND PRECAUTIONS
KEEP WORK AREA CLEAN AND DRY.
Cluttered, damp or wet work areas invite injuries.
STAY ALERT. Watch what you are doing at all times. Use common
sense. Do not use the greenhouse when you are tired or distracted from
the job at hand. It is recommended to use gloves for assembling the
greenhouse.
MAINTAIN THIS PRODUCT WITH CARE.
Keep the greenhouse clean and dry for better performance:
maintenance should be performed regularly.
USE THE RIGHT PRODUCT FOR THE JOB.
Do not attempt toforce a small product to do the work of a larger
industrial product. There are certain applications for which the
greenhouse was designed. It will do the job better and more safely in the
manner for which it was intended. Do not modify the greenhouse and do
not use the greenhouse for a purpose for which it was not intended.
MAINTAIN A SAFE WORKING ENVIRONMENT.
Keep the work area tidy. Make sure there is adequate surrounding
workspace. Avoid high traffic areas. Always keep the work area free of
obstructions, grease, oil, trash and other debris.
PROPER GREENHOUSE LOCATION.
Make sure the greenhouse is located on a flat, level surface.
TO PREVENT INJURY, PLEASE READ AND UNDERSTAND THE
GREENHOUSE ASSEMBLY INSTRUCTIONS MANUAL BEFORE
USE.
Notes:
1. Around 2-3 hours is needed to assemble the greenhouse by 2-3
individuals.
2. The UV-protected side of the panel sheets is covered with opal
white film and must be placed facing the sun.
3. Before installing the sheets, remove around 2 inches of film from all
the edges. Once the construction is completed, remove the the entire
film immediately.
4. Ensure that the greenhouse is located on a flat and level surface.
GENERAL SAFETY, WARNINGS AND PRECAUTIONS
KEEP WORKING AREA CLEAN AND DRY.
Cluttered, damp or wet working areas invite injuries.
BE ALERT. Always be cautious of your actions. Use your common
sense. Do not assemble the structure if you are tired or distracted.
Use gloves when assembling the greenhouse.
HANDLE THIS PRODUCT WITH CARE
Keep the greenhouse clean and dry to maintain better performance.
Also, regular maintenance must be done.
USE THE SUITABLE TOOLS FOR THE JOB
Do not use small tools in lieu of larger ones. Tools are not suitable for
every type of work. The greenhouse is designed in order to provide
better condition and safety. So, do not perform any modification on
the greenhouse. Do not use it aside from its intended purpose.
MAINTAIN A SAFE WORKING ENVIRONMENT
Keep your working area clean and organized. Make sure that there is
enough space for you to work on. Avoid crowded areas. Also, keep
source of obstruction, grease, oil or trash far from your working zone.
PROPER GREENHOUSE LOCATION
Place the greenhouse on a flat and level surface.
6X6FT
79 inches x 76 inches x 75 inches
OGAL-666A
Notes:
1. Remove approximately 2 inches of film from all the sheet edges prior to installation.
Upon completion, immediately remove all the remaining film.
2. The UV-protected side of the sheet, which is covered with opal white film, must face
the sun.
Front
Rear
Notes:
1. Remove approximately 2 inches of film from all the sheet edges prior to installation.
Upon completion, immediately remove all the remaining film.
2. The UV-protected side of the sheet, which is covered with opal white film, must face
the sun.
Front
Rear
1 | OGAL-666A ASSEMBLY INSTRUCTIONS
1.1 Create a right angle by positioning
the parts of F-03b and F-04. However,
make sure that the grooves of F-03b and
F-04 are placed outside.
1.2 Form a right angle using two F-04
parts, but ensure that the edges of
these pieces are located on the
outside.
These are the parts used in this section.
Image
Item No.
Qty
These are the parts used in this section.
Image
Item No.
Qty
2.1.1 Insert the F-B14 bolts into the holes.
2.1.2 From the top, insert F-05 into the
previously placed F-B14 bolts.
2.1.3 and 2.1.4 Tighten and secure with nuts.
3
3.1.2 Connect F-05, F-19b, F-18 by
the upper bolt. Once the notch on
F-19b is aligned with the top of F-05,
you can screw the nut tight on the bolt.
OGAL-666A ASSEMBLY INSTRUCTIONS | 4
These are the parts used in this section.
3.1.1 Insert two bolts into F-05 and cross
its upper bolt to the lowest hole of F-19b.
3.1.2 When the notch of F-19b is
already aligned with the top of F-05,
tighten and secure with a nut.
3.2 Follow the same process performed in figure 3.1.
Image
Item No.
Qty
4.1 Connect F-18 and F-29 to F-05 using
bolts and nuts. When connecting these
pieces, maintain a 3/4 of an inch distance
from the bolts to the top of F-05.
4.2 Using bolts and nuts, connect F-29 to
F-04.
NOTE: Do not tighten the nuts yet.
These are the parts used in this section.
Image
Item No.
Qty
5 | OGAL-666A ASSEMBLY INSTRUCTIONS
6.1 Insert F-08, F-09, F-10 and F-11 into the
bolt and secure it with nuts.
6.2 Individually insert one bolt into F-08
and F-09. Then, connect F-18 to F-08 and
F-09 and tighten using bolts and nuts.
6.3 Insert one bolt each
into F-10 and F-11.
Connect F-17 to F-10
and F-11 with bolts and
nuts. Afterwards,
connect F-17 to F-05
through the hole
mentioned in step 5.3
using a bolt and nut.
These are the parts used in this section.
Image
Item No.
Qty
5.1 Connect F-30 and F-05 to
the lowest notch of F-19b
using bolts and nuts.
NOTE: Align the top of F-05
with the notch of F-19b.
5.2 Using bolts and nuts, connect F-30 to F-04.
NOTE: Do not tighten the nuts yet.
5.3 Insert two bolts into
F-05, then, connect F-30
and F-05 to the lowest
notch of F-19b using the
lower bolt and nut. next,
insert the above bolt to
the remaining lower hole
of F-19b.
NOTE: The notch of F-19
must be aligned with the
top of F-05.
These are the parts used in this section.
Image
Item No.
Qty
OGAL-666A ASSEMBLY INSTRUCTIONS | 6
6.1 Insert F-08, F-09, F-10 and F-11 into the
bolt and secure it with nuts.
6.2 Individually insert one bolt into F-08
and F-09. Then, connect F-18 to F-08 and
F-09 and tighten using bolts and nuts.
6.3 Insert one bolt each
into F-10 and F-11.
Connect F-17 to F-10
and F-11 with bolts and
nuts. Afterwards,
connect F-17 to F-05
through the hole
mentioned in step 5.3
using a bolt and nut.
These are the parts used in this section.
Image
Item No.
Qty
5.1 Connect F-30 and F-05 to
the lowest notch of F-19b
using bolts and nuts.
NOTE: Align the top of F-05
with the notch of F-19b.
5.2 Using bolts and nuts, connect F-30 to F-04.
NOTE: Do not tighten the nuts yet.
5.3 Insert two bolts into
F-05, then, connect F-30
and F-05 to the lowest
notch of F-19b using the
lower bolt and nut. next,
insert the above bolt to
the remaining lower hole
of F-19b.
NOTE: The notch of F-19
must be aligned with the
top of F-05.
These are the parts used in this section.
Image
Item No.
Qty
7 | OGAL-666A ASSEMBLY INSTRUCTIONS
Slide the poly-carbonate panels into
the designated area.
These are the parts used in this section.
Image
Item No.
Qty
7.1 Connect F-23 to F-04 with a tightened
nut and bolt.
7.2 Slide a bolt into the slit in F-23, and
perpendicularly attach F-18 through the
designated hole. Tighten the nut.
These are the parts used in this section.
Image
Item No.
Qty
OGAL-666A ASSEMBLY INSTRUCTIONS | 8
Slide the poly-carbonate panels into
the designated area.
These are the parts used in this section.
Image
Item No.
Qty
7.1 Connect F-23 to F-04 with a tightened
nut and bolt.
7.2 Slide a bolt into the slit in F-23, and
perpendicularly attach F-18 through the
designated hole. Tighten the nut.
These are the parts used in this section.
Image
Item No.
Qty
9 | OGAL-666A ASSEMBLY INSTRUCTIONS
This is the part used in this section.
Image
Item No.
Qty
10.1 Place the bolt and nut into the hole
of F-B06, but do not tighten the nut yet.
10.2 Insert two bolts each into F-08, F-09,
F-10 and F-11.
10.3 Place the bolts
and nuts in the hole
of F-19b as shown
in the picture, but
do not tighten the
nuts yet.
9.1 Insert the bolts and nuts in each hole
of F-B06, but do not tighten the nuts yet.
Then, insert the bolts into the grooves of
F-05.
9.2 Insert the bolts into the grooves of F-23.
These are the parts used in this section.
Image
Item No.
Qty
OGAL-666A ASSEMBLY INSTRUCTIONS | 10
This is the part used in this section.
Image
Item No.
Qty
10.1 Place the bolt and nut into the hole
of F-B06, but do not tighten the nut yet.
10.2 Insert two bolts each into F-08, F-09,
F-10 and F-11.
10.3 Place the bolts
and nuts in the hole
of F-19b as shown
in the picture, but
do not tighten the
nuts yet.
9.1 Insert the bolts and nuts in each hole
of F-B06, but do not tighten the nuts yet.
Then, insert the bolts into the grooves of
F-05.
9.2 Insert the bolts into the grooves of F-23.
These are the parts used in this section.
Image
Item No.
Qty
11 | OGAL-666A ASSEMBLY INSTRUCTIONS
12.1 Insert one bolt into F-06 and F-07,
then insert into the hole of F-B07.
These are the parts used in this section.
Image
Item No.
Qty
11.1 Insert F-06 and F-07 through the bolts
inserted in F-19b and F-B06. then, tighten the
nuts.
11.2 Slide the bolts which were inserted
through F-08 and F-09 through the holes
in F-19 as shown.
11.3 Insert two bolts into the grooves of F-06
and F-07, then, cross the bolts into the hole of
F-19 and tighten.
NOTE: The side with 3 holes must be upward
as correctly shown in 11.3 (left).
These are the parts used in this section.
Image
Item No.
Qty
OGAL-666A ASSEMBLY INSTRUCTIONS | 12
12.1 Insert one bolt into F-06 and F-07,
then insert into the hole of F-B07.
These are the parts used in this section.
Image
Item No.
Qty
11.1 Insert F-06 and F-07 through the bolts
inserted in F-19b and F-B06. then, tighten the
nuts.
11.2 Slide the bolts which were inserted
through F-08 and F-09 through the holes
in F-19 as shown.
11.3 Insert two bolts into the grooves of F-06
and F-07, then, cross the bolts into the hole of
F-19 and tighten.
NOTE: The side with 3 holes must be upward
as correctly shown in 11.3 (left).
These are the parts used in this section.
Image
Item No.
Qty
13 | OGAL-666A ASSEMBLY INSTRUCTIONS
14.1 Slide one bolt into the bottom of each
of the four F-24 frames, and connect two to
each F-B06 frames at the top of the left and
right walls.
These are the parts used in this section.
Image
Item No.
Qty
j
14.2 Slide one more bolt into the tops of
each of the four F-24 frames and connect
to the ridge frame F-B07. Tighten screws.
14.2
13.1 Insert F-40 to F-06 and F-07.
Afterwards, connect F-12 to F-19 using a
bolt and nut.
These are the parts used in this section.
Image
Item No.
Qty
14.1 Slide one bolt into the bottom of each
of the four F-24 frames, and connect two
to each F-B06 frames at the top of the left
and right walls.
14.2 Slide one bolt into each F-24 in the right
side of roof.
14.3 Slide one more bolt into the tops of each
of the four F-24 frames and connect to the ridge
frame F-B07. Tighten screws.
15 | OGAL-666A ASSEMBLY INSTRUCTIONS
16.2 Slide F-B05 into F-B06 as shown.
16.1 Connect F-28 to F-24 using the bolts
left in F-24 and tighten with nuts.
These are the parts used in this section.
Image
Item No.
Qty
Place the poly-carbonate panels into
each designated area.
These are the parts used in this section.
Image
Item No.
Qty
Other oGrow Greenhouse Kit manuals
oGrow
oGrow OG03AL86-BKE User manual
oGrow
oGrow OGAL-46A User manual
oGrow
oGrow OGAL-866A Quick start guide
oGrow
oGrow OGAL-466A User manual
oGrow
oGrow OGAL-46 User manual
oGrow
oGrow OG03-PE5565E User manual
oGrow
oGrow Walk-in OGAL-466 User manual
oGrow
oGrow OGAL-CF23 User manual
oGrow
oGrow Walk-in OGAL-666 User manual
oGrow
oGrow OGAL-866 User manual
Popular Greenhouse Kit manuals by other brands
Janssens
Janssens HELIOS SL Mounting instructions
LAMS
LAMS LAURUS 784817 Assembly instructions
C.A.P.
C.A.P. XGC-1e Specification sheet
Flower House
Flower House OrchidHouse Setup instructions
Greenhouse Style
Greenhouse Style PC812SG instructions
Elite Greenhouses
Elite Greenhouses TITAN K800 Instructions & Illustrations
Vitavia
Vitavia VM0005-V 6200 Assembly instructions
Summer Garden Buildings
Summer Garden Buildings Greenhouse 05 instructions
Halls
Halls Universal 108 manual
Grandio
Grandio Summit Series installation manual
Halls Greenhouses
Halls Greenhouses Qube 66 Assembly instructions
Elite Greenhouses
Elite Greenhouses 6'3" WIDE CRAFTSMAN Instructions & Illustrations
