OHAUS Defender D5K1S User manual

DefenderTM 6000 Series Base
Instruction Manual

Defender Series Base EN-1
INTRODUCTION
This manual covers installation, and maintenance instructions for the OHAUS Defender TM Series Base. Please
read this manual completely before installation and operation.
SAFETY PRECAUTIONS
For safe and dependable operation of this product, please comply with the following precautions:
Operate the base only under ambient conditions specified in these instructions
Ensure that the load cell cable does not pose an obstruction or tripping hazard
Do not operate the base in hazardous environments or unstable locations
Do not drop loads on the base
Do not lift the base by the top frame; always lift from the bottom frame when moving the
base
Service should only be performed by authorized personnel
INSTALLATION
Unpacking
Unpack and inspect the product to make sure that all components have been included. The package includes the
following:
• Defender TM Series Base • Weighing Pan • Instruction Manual
When purchased as a complete Defender Series Scale, the package will also include:
• Indicator • Column Assembly
ASSEMBLY
Weighing Pan
Remove the shipping spacers, and place the weighing pan securely over the rubber load pads on the top frame of
the base.
Wiring Connections
When connecting the base to an OHAUS indicator equipped with the matching circular connector, push the base
connector onto the indicator connector and turn the locking ring clockwise to lock it in place.
When connecting the base to an indicator that does not have the matching connector, install the optional load cell
cable adapter (P/N 30429931sold separately) to the indicator using the wiring codes in Table 1. Then attach the
load cell cable to the cable adapter.
Note: As an alternate wiring method, cut off the connector, strip the wires and attach them to the indicator using
the wiring codes in Table 1.
The extension cable accessory (P/N: 30429931) cannot be used if the scale will be used in a legal for trade or
legally controlled application, because there is no provision to seal the connection between the indicator and
platform.

EN-2 Defender Series Base
TABLE 1. LOAD CELL CONNECTION
Type1. For model i-D5K1S, i-D12K1R, i-D25K1R, i-D50K1L, bases
FUNCTION WIRE COLOR
+ Excitation Blue
- Excitation Black
+ Signal White
- Signal Red
+ Sense Green
- Sense Grey
Shield Yellow
Type2. For model i-D150K1L base
FUNCTION WIRE COLOR
+ Excitation Green
- Excitation Black
+ Signal White
- Signal Red
+ Sense Light Yellow
- Sense Blue
Shield Deep Yellow
Selecting the Location
To ensure accuracy, proper performance and safety, locate and operate the base on a stable, level surface. Avoid
locations with rapid temperature changes or excessive dust, air currents, vibrations, electromagnetic fields or heat.
Level the base by adjusting the four leveling feet until the bubble in the level indicator is centered. A wrench may
be needed to loosen the locking nut above each leveling foot. When the base is level, retighten the locking nuts up
against the base to lock each foot into place.
Note: Ensure that the base is level each time its location is changed.
CORRECT INCORRECT
MAINTENANCE
Cleaning
The base components should be kept clean and free of excessive material build up.
A damp cloth with water and a mild detergent may be used to wipe clean the external surfaces – do not
use acids, alkalis, strong solvents or abrasive materials.
To maintain surface integrity, do not allow debris to remain on the surface of the painted or stainless steel base
frame.
Remove the pan and use fresh water to clean the base frame surface of any debris. Dry the base with a
clean cloth or allow to air dry before replacing the pan. Repeat daily for best care.

Defender Series Base EN-3
Troubleshooting
Aside from installing components and leveling adjustments, the Defender Series Base does not require any other
adjustments as shipped from the factory.
Operational difficulties that may be encountered can often be traced to simple causes such as:
Loose or incorrect wiring connections
Failure to remove the shipping spacers
Obstructions to the base frame
Unstable environments
Incorrect calibration or setup of the indicator
If the troubleshooting section does not resolve or describe your problem, contact your authorized OHAUS service
agent. For service assistance or technical support in the United States call toll-free 1-800-526-0659 between 8:00
AM and 5:00 PM EST. An OHAUS product service specialist will be available to provide assistance. Outside the
USA, please visit our web site, www.ohaus.com to locate the OHAUS office nearest you.
TECHNICAL DATA
Technical Specifications
The technical data is valid under the following ambient conditions:
Operating temperature: -10ºC to +40 ºC (14 °F to 104 °F)
Relative humidity: 100% relative humidity, non-condensing
Altitude: Up to 2,000m
Note: Not all models may be available in your area. Check with your local OHAUS representative.
TABLE 2.1 SPECIFICATIONS
MODEL i-D5K1S i-D12K1R i-D25K1R i-D50K1L i-D150K1L
Capacity 10 lb /
5 kg
25 lb /
12.5 kg
50 lb /
25 kg
100 lb /
50 kg
300 lb /
150 kg
Approved Resolution NTEP/MC 5000 NTEP/MC 3000
Safe Overload Capacity 150% of capacity
Pan Dimensions 254 x 254 mm
10 x 10 in
305 x 305 mm
12 x 12 in
400 x 500 mm
15.7 x 19.6 in
Base Construction
316 stainless steel top and bottom frame,
hermetically sealed IP68/IP69K stainless
steel loadcell.
316 stainless steel removable
weighing platform with 316
stainless steel frame,
hermetically sealed
IP68/IP69K stainless steel
loadcell.
Repeatability
(std.deviation) 2d
Linearity ±2d
Load Cell Capacity 10 kg 20 kg 50 kg 100 kg 200 kg
Load Cell Cable 50cm L x 6-wire 1m L x 6-wire
Load Cell Type 350 Ohm, SST, single point
Load Cell Excitation 3.3-15V DC/AC
Load Cell Rated Output 2mV/V
Load Cell Protection IP69K
Net Weight 6 kg / 13.2 lb 7.5 kg / 16.5 lb 16 kg / 35.3 lb
Shipping Weight 7 kg / 15.4 lb 8.5 kg / 18.7 lb 18 kg / 39.7 lb

EN-4 Defender Series Base
Drawings
Figure 1. Defender Base Dimension Drawing.
TABLE 3. DIMENSIONS
Base
A B C D
Pan Depth Pan Width Height of Pan to
Surface of Table Height of Pan
i-DxxxKxS 254 mm 254 mm 106 mm N/A
i-DxxxKxR 305 mm 305 mm 106 mm N/A
i-DxxxKxL 400 mm 500 mm 136.5 mm 80 mm
*For leveling purposes, the feet may be extended up to an additional 15 mm.

Defender Series Base EN-5
COMPLIANCE
Compliance to the following standards is indicated by the corresponding mark on the product.
Mark Standard
This product complies with the applicable harmonized standards of EU Directives 2011/65/EU
(RoHS). The EU Declaration of Conformity is available online at www.ohaus.com/ce.
This product complies with the EU Directive 2012/19/EU (WEEE). Please dispose of this
product in accordance with local regulations at the collecting point specified for electrical and
electronic equipment.
For disposal instructions in Europe, refer to www.ohaus.com/weee.
ISO 9001 Registration
The management system governing the production of this product is ISO 9001 certified.
ACCESSORIES
TABLE 4. ACCESSORIES
Part Number Description
30616409 Wheel Kit, Defender Series
30626654 Mounting Set Front SST
30572907 External power bank sealing kit
30424409 Cable Extension 9m D52
30429931 Cable Kit Extension for base
30572908 Column Kit 260mm 316 D61
30572909 Column Kit 670mm 316 D61

EN-6 Defender Series Base
LIMITED WARRANTY
OHAUS products are warranted against defects in materials and workmanship from the date of delivery through
the duration of the warranty period. During the warranty period OHAUS will repair, or, at its option, replace any
component(s) that proves to be defective at no charge, provided that the product is returned, freight prepaid, to
OHAUS. This warranty does not apply if the product has been damaged by accident or misuse, exposed to
radioactive or corrosive materials, has foreign material penetrating to the inside of the product, or as a result of
service or modification by other than OHAUS. In lieu of a properly returned warranty registration card, the warranty
period shall begin on the date of shipment to the authorized dealer. No other express or implied warranty is given
by OHAUS Corporation. OHAUS Corporation shall not be liable for any consequential damages.
As warranty legislation differs from state to state and country to country, please contact OHAUS or your local
OHAUS dealer for further details

Base serie Defender ES-1
INTRODUCCIÓN
Este manual describe instrucciones de instalación y mantenimiento para la base de la serie Defender™ de
OHAUS. Lea completamente este manual antes de la instalación y funcionamiento.
PRECAUCIONES DE SEGURIDAD
Para una operación segura y confiable de este producto, respete las siguientes precauciones:
Opere la base solamente bajo las condiciones ambientales especificadas en estas
instrucciones
Asegúrese de que el cable de la celda de carga no represente un riesgo de obstrucción o
de tropiezo
No utilice la base en entornos peligrosos o en lugares inestables
No deje caer cargas sobre la base
No levante la base por medio de la parte superior del marco, levántela siempre por medio
de la parte inferior al mover la base
Cualquier reparación y servicio debe ser realizado solo por personal autorizado
INSTALACIÓN
Desembalaje
Desembale e inspeccione el producto para asegurarse de que incluye todos los componentes. El paquete
contiene lo siguiente:
• Base de la serie DefenderTM • Plato de pesaje • Manual de instrucciones
Si es adquirida como una báscula de la serie Defender, el paquete también contiene:
• Indicador • Unidad de columna
MONTAJE
Plato de pesaje
Retire los espaciadores de envío y coloque el plato de pesaje firmemente sobre las almohadillas de caucho en el
marco superior de la base.
Conexiones del cableado
Al conectar la base a un indicador OHAUS equipado con el correspondiente conector circular, empuje el conector
de la base en el conector del indicador y gire el anillo de bloqueo para asegurarlo.
Si conecta la base a un indicador que no tenga el conector correspondiente, instale el adaptador opcional del
cable de la celda de carga (P/N 30429931 vendido por separado) para el indicador utilizando los códigos de
cableado en la tabla 1. A continuación conecte el cable de la celda de carga al adaptador del cable.
Nota: Como un método de cableado alternativo, corte el conector, pele los cables y conéctelos al indicador
utilizando los códigos de cableado en la tabla 1.
El cable de extensión accesorio (P/N: 30429931) no puede utilizarse si la báscula va a tener un uso
comercial legal o una aplicación controlada legalmente, ya que no existe disposición para sellar la
conexión entre el indicador y plataforma.

ES-2 Base serie Defender
TABLA 1. CONEXIÓN DE LA CELDA DE CARGA
Tipo 1. Bases i-D5K1S, i-D12K1R, i-D25K1R, i-D50K1L
FUNCIÓN COLOR DEL
CABLE
+ Excitación Verde
- Excitación Negro
+ Señal Rojo
- Señal Blanco
+ Detección Azul
- Detección Marrón
Blindaje Amarillo
Tipo2. Bases i-D150K1L
FUNCIÓN COLOR DEL
CABLE
+ Excitación Verde
- Excitación Negro
+ Señal Blanco
- Señal Rojo
+ Detección Azul
- Detección Marrón
Blindaje Amarillo
Seleccionar la ubicación
Para garantizar la precisión, funcionamiento correcto y seguridad, coloque y opere la base sobre una superficie
estable y nivelada. Evite los lugares con cambios rápidos de temperatura o exceso de polvo, corrientes de aire,
vibraciones, campos electromagnéticos o calor.
Nivele la base ajustando los cuatro pies de nivelación hasta que la burbuja en el indicador de nivel quede centrada.
Puede ser necesaria una llave para aflojar la tuerca de seguridad situada sobre cada pie de nivelación. Cuando la
base esté nivelada, apriete las tuercas de seguridad contra la base para bloquear cada pie en su lugar.
Nota: Asegúrese de que la base esté nivelada cada vez que
cambie su ubicación.
CORRECTO INCORRECTO
MANTENIMIENTO
Limpieza
Los componentes de la base deben mantenerse limpios y libre de acumulación excesiva de material.
Puede utilizar un paño humedecido con agua y un detergente suave para limpiar las superficies externas,
no use ácidos, álcalis, disolventes fuertes o materiales abrasivos.
Para mantener la integridad de la superficie, no permita que haya suciedad en la superficie pintada o de acero
inoxidable de la estructura de la base.
Retire el plato y utilice agua fresca para limpiar la superficie de la estructura de la base. Para secar la
base, utilice un paño limpio o deje secar al aire antes de reemplazar el plato. Repetir diariamente para
mantener un buen cuidado.