olympia electronics BS-470 User manual

BS-470
BS-470
Shielded input stage to protect against
external interference
Normal and high-sensitivity mode to prevent
small pets activation
Maximum coverage, on the vertical axis, 12m.
Protection from reverse battery installation
Elegant design
Thank you for your trust in our products
Olympia Electronics - European manufacturer
The wireless infrared motion detector BS-470
incorporates a special high efficiency, multi-focal
and wide angle lens. Microprocessor controlled
improved circuitry along with a shielded input
stage ensure maximum protection and external
interference avoidance thus avoiding false
triggering of the device.
The housing of the device has the appropriate
infrastructure to be placed either on a flat surface
or at an angle of surfaces when required.
The device must be mounted in such a position in
order to permit the best possible surveillance.
The mounting height should be between 2.2 and
2.5 meters, with an ideal height of 2.4 metres.
In order to avoid unintended false alarms, the
detectors must not be mounted in areas that have
hot air or air drafts in general such as over
radiators. It must not be mounted near devices that
emit radio waves such as WiFi repeaters and also
must not be in the path of direct sunlight.
Room
door
Balcony door Window
Mounting example in a typical room
BS-470
The sensitivity selection can be used to avoid false
triggering in the presence of small pets.
MOUNTING THE DEVICE
MOUNTING THE DEVICE
Wireless infrared motion detector
for BS-468/A burglar alarm panel
Wireless infrared motion detector
for BS-468/A burglar alarm panel
Page 1 of 5 921470000_09_005

If normal sensitivity is selected then care must
be taken that house pets do not have access
to furniture that is near or at the same height as
the detector in order to avoid false triggering.
Physical obstructions such as walls, furniture,
separators, glass dividers e.t.c must be
avoided because they will degrade the
detection area of the detector.
The room’s ambient temperature is a factor
that plays a significant role in the detection
range of the detector. In hot summer months
the detection range is degraded and can be
compensated if we select high sensitivity
during these months.
The device is unsuitable for outdoor use.
9m.9m.
12m.
Surveillance zone distribution in the horizontal plane
Surveillance zone distribution in the vertical plane
Page 2 of 5
2,4m.
To remove the top cover insert a flat blade
screwdriver in the slot. Push the screwdriver gently
to unlock the latch and remove the cover, as shown
in the photo below.
After removing the top cover it is suggested to
gently remove the circuit board by removing its
retaining screw, as shown in the photo 3 of page 3.
Take care not to touch the IR sensor surface. This
will affect is operation.
Photograph 4 (page 3) shows the interior of the
plastic base as well as the cable entry and
mounting hole positions.
To mount the unit to the wall, increase the hole
diameter of points Α to 4 mm. using a suitable drill
bit and mount the unit using the supplied mounting
accessories.
The same can be done if we require to mount the
unit at an angle or in a corner. Drill out points Β, on
the side that will have contact with the wall and use
the supplied mounting accessories. In corner
mounting, it will require two additional screws and
the corresponding plugs.
When mounting has been finished reinstall the
circuit board, if it was removed, and fasten it using
the respective screw. Care should be taken when
using the screw driver in order to avoid any
damage.
After that the connections with an external contact
can be made, if necessary.
INTERNAL LAYOUT AND SETTINGS
INTERNAL LAYOUT AND SETTINGS
The device can be connected
with external contacts, via the KL1 terminal
Photo 1
Photo 2
921470000_09_005

Point A
mounting point
for wall mounting
Point A, mounting point
for wall mounting
Point Β
Angle or
corner
mounitng
Point C
Cable entry
Point C
Cable entry
Page 3 of 5
Photo 4
Wireless motion detector includes -s its settings 2 DIP witches for (DS1).
DIP-switch 1: ON ensures input and output delays for detectors installed at the entrance of a building. OFF allows the
detector to trigger an alarm immediately if the control panel is armed. The DIP-switch has an effect only if
the detector is programmed in physical response from the control panel (zone with delay or zone without
delay).
Attention!! Selecting the delay zone from the board is required by BS-468 / A.
DIP-switch 2: When is set to OFF, the device is in normal mode. When is set to ON it is in high sensitivity mode and
increases the detection range.
It also has a terminal for connecting an external magnetic contact which, when not in use, must be short-circuited.
Wall mounting Angle mounting Corner mounting
INTERNAL LAYOUT AND SETTINGS (continued)
INTERNAL LAYOUT AND SETTINGS (continued)
DIP-SWITCH SETTINGS
DIP-SWITCH SETTINGS
Photo 3
DS1
Connection
Terminal
Settings
Dip-switch
Tamper
Switch
Battery
CR123A
Input stage
shielding
Infrared
sensor
Circuit board
retaining screw
921470000_09_005

Once the device is connected to the panel's network, remove the battery and wait for 10 seconds.
Then press the tamper and reinstall the battery. Wait until the LED lights up. Once you release the
tamper, the LED will go out. In this case, the range test will start. During range test the device LED
blinks every second. The duration of range test is 60-95 seconds. When it is finished the LED goes off
and after 2 seconds the test result is displayed as follows:
Single blink: Strong signal. The device can be safely installed at this point.
Two blinks: Normal signal. The device can be safely installed at this point.
Three blinks: Weak signal. It is recommended not to install the device at this point. There will be
communication bettween the device and the control panel but there will
be communication packets losses.
Four blinks: Out of range. The device is forbidden to be placed in this point.
Note: As soon as the test procedure is started, it is suggested that the device cover will be placed
directly in order to simulate the actual communication conditions. The environment must be also
adapted to the worst possible conditions (eg closed doors).
Finally, in case of home improvements or renovation, it is suggested to perform a range test again.
RANGE TEST
RANGE TEST
BATERRY REPLACEMENT
BATERRY REPLACEMENT
The detector checks its battery voltage and transmits the information to the panel. When the control
panel displays a low battery indicator, the detector will continue to operate for at least 2 weeks.
Nevertheless it is recommended to replace the battery as soon as possible. This must be done by a
qualified technician and the control panel must be in service mode.
I s not allowed to discard batteries in to common trash bins, they must be discarded only t i
in battery recycling points. Do not incinerate.
Page 4 of 5 921470000_09_005
KL1
Figure 1
Example of connection NC external magnetic contacts
with BS-470
The device can be connected to external magnetic contacts via the KL1 terminal block (Figure 1). If a magnetic field
is connected to this input, the device sends an alarm signal to the control panel. If the contact is not connected to an
external device, at the cable terminal of the KL1, then manufacturer’s cable must remain.
NOTE:The maximum distance of the external sensor cable is 3 meters !!!
CONNECTION WITH EXTERNAL MAGNETIC CONTACTS
CONNECTION WITH EXTERNAL MAGNETIC CONTACTS

52.5mm.
61.5mm.
99mm.
Page 5 of 5
EXTERNAL DIMENSIONS OF DEVICE
EXTERNAL DIMENSIONS OF DEVICE
WARRANTY
WARRANTY
921470000_09_005
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty is
specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which accompanies
each product. This warranty ceases to exist if the buyer does not follow the technical instructions included in
official documents given by Olympia Electronics or if the buyer modifies the goods provided or has any repairs
or re-setting done by a third party, unless Olympia Electronics has fully agreed to them in writing. Products that
have been damaged can be returned to the premises of our company for repair or replacement, as long as the
warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the buyer
depending on the reason of defection. Olympia Electronics reserves the right to charge or not the buyer the
transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
POWER SUPPLY
BATTERY LIFE
COMMUNICATION RANGE
DETECTION RANGE
ACTIVATION TIME
OUTPUT RELAY RATING
INITIAL SETUP TIME
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
DEGREES OF PROTECTION
ENVIRONMENTAL CLASS
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
CONSTRUCTION MATERIAL
EXTERNAL DIMENSIONS (LxWxH)
TYPICAL WEIGHT
GUARANTEE
2 years minimum (without using external contacts)
CR-123A lithium battery (3V rated voltage)
About 200m (open area)
9 - 12 meters, adjustable
0.25 - 0.3 sec.
30V - 0.2A DC
1 minute (the indication LED blinks)
ο
-10 to +50 C
Up to 95%
2
II
IP40
ΕΝ50131-1, ΕΝ50131-2-2, ΕΝ50130-4, ΕΝ61000-6-3
ABS/PC
61.5 x 52.5 x 99 mm.
70 gr.
2 years
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS