olympia electronics ZLD-34 User manual

SELF-TESTING MAINTAINED ILLUMINATION SIGNS WITH WHITE LEDs
ZLD-34
TECHNICAL CHARACTERISTICS
Operation temperature range
Relative humidity
Construction materials
External dimensions
Typical weight
Guarantee
Mains voltage
Maximum power consumption
Batteries (Ni-MH)
Recharging time
Battery protection
Indications
Minimum emergency duration
Degrees of cover protection
Produced in accordance with
Light source intensity (230V) / (emerg.)
220-240V AC/50-60Hz
3h
24h
Overcharging and full discharging protection
Charge LED, Lamp Fault LED, Fault LED
IP 40
3.6V/1.5Ah
145lm / 125lm
8.5 VA
EN 60598-1, EN 60598-2-22, EN 1838
o
0 to 40 C
up to 95%
Aluminum, plexiglas
3 years (1 year for the battery)
1020gr.
350x225x38mm
922503452_09_011
Page 1 from 4
Operation instructions
automatically every 15 days. In order to be
Installation
To install the illumination sign you must performed, the main power supply and the
connect the battery first (see page 4) and battery should be connected.
follow the installation instructions in pages 2
and 3. Automatic Autonomous Test
The Automatic autonomous Test is
Battery Cut-off conducted and measures the luminaire`s
The luminaire enters in this operation when back up operation. This test is conducted
the mains power supply fails and battery automatically every six months. In order to
has lost its energy. During this operation the be performed, the main power supply and
luminaire enters the idle state and battery the battery should be connected (the battery
consumption is negligible, in order to be should be charged). If the battery is not
protected from deep discharge. charged, the test is postponed until the
battery is completely charged.
Battery charging
The battery charging is completely Back Up Operation
controled. In this case, is achieved the The autonomous duration of battery during
perfect battery maintenance , as well as emergency mode is at least the one that is
the elongation of its duration. When the stated in the list of the first page. During
battery has completely charged, it charges emergency mode, a LED strip test is also
with a maintenance current. performed.
Manual Test Resetting Errors
The manual test can be conducted only if Push the Test button for 5 seconds, to
the main power supply and the battery is extinguish all the indicated LED errors.
connected.By pressing the test button Then the luminaire enters regular operation
briefly an operation test is initiated. During mode.
this test period all indication LEDs are OFF.
Automatic test
This test includes all the operations that
provide the manual test and is conducted
Battery installation and replacement process
1 Unfasten the 4 screws without moving the marking panel.
2 Unfasten the 4 screws and remove the marking panel.
3 Slide out carefully the electronic parts and the battery.
4 Install the battery’s connector to the appropriate P.C.B connector.
5 Slide in carefully the electronic parts and the battery.
6Refit the marking panel and fasten the removed screws in steps 1 and 2.
WARNING!! Use a maximum torque of 0,25Ímto tighten the screws.
ÍÏÔÅ!!
In case of battery replacement remove the used battery and place a new one with the same type.
General:
1. Operations for installation, maintainance or testing must be done by authorized personel only.
2. The device must be connected to the mains power supply thru a fuse dependent by the total
amount of the line’s power load.
t i
in battery recycling points. Do not incinerate.
NOTE:
LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained 1: Maintained A: Including test device 180: 3 hour duration
3. In case of inactive use for a period greater than 2 months, disconnect the battery by pulling out
the battery’s connector.
4. I s not allowed to discard batteries in to common trash bins, they must be discarded
only
12
922503452_09_011
Page 4 from 4
3
4

922503452_09_011
Page 3from 4
922503452_09_011
Page 2 from 4
Indication LED status (with connected Ïff:Battery OK.
mains power supply). Blink (With AC Charge LED ON):
AC Charge Autonomy or low battery problem
On: Good charge current. (the battery must be replaced).
Ïff: No battery (No charging Blink (With AC Charge LED Off):
current or disconnected battery). No charging current or disconnected
battery.
Lamp fault
Ïn: faulty LED strip.
Off: Good LED strip.
Fault
Ceiling mounting
Mounting methods
Recessed mounted installation
on suspended ceilings using
the base type Á-1020
A-1020
342
75
Ö6
Electric connection and dimensions (in mm)
ZLD-34 : 350(á) x 165(â)
Suspended ceiling
mounting bases
â
60mm
á
Hanging installation on
suspended ceilings using the special
mounting brackets contained
in the package. 2.Tighten the screw
1. Place the plastic part
3. Pass the cable thru the knock out
and connect the wires to the terminal block
4. Place the mounting accessories on the wall
and tighten the mounting screw
5. Place the plastic cover
Alternative mounting method
Wall mounting
3. Pass the cable thru the nut and the
extension pipe and tighten it
6. Hang the luminaire and adjust the
metall cover by the screw of the
metall ring
2. Tighten the screw
1. Place the plastic part
4. Pass the cable thru the knock out
and connect the wires to the terminal block
5. Place the plastic cover
ATTENTION!!!
All metall parts must be connected to ground
A limited number of extensions can be used in order to
maintain the stability of the luminaire
2. Tighten the screw
1. Place the plastic part
3. Pass the cable thru the knock out
and connect the wires to the terminal block
4. Place the mounting accessories in the wall
and tighten the mounting screw
5. Place the plastic cover
Wall in bottom view
Hanging installation
using the special
mounting sets
Flag mounted installation on
a wall using the special
mounting bracket
contained in the package. 2. Tighten the screw
4. Place the mounting accessories in the wall
and screw the mounting screws
3. Connect the wires to the terminal block and pass
the cable thru the knock out
1. Place the single mounting plastic part
Wall mounted installation
using the special mounting
brackets contained in the
package.
Extension ability
In recess mounting in suspended ceiling or in external ceiling
mounting, we can use the Á-1022 extension set (20 cm), the Á-1025
extension set (40 cm), and the Á-1026 (60 cm)extension set after
request.
A-1026
A-1022
A-1025
TYPE
DESCRIPTION
Extension set 20 cm.
Extension set 40 cm.
Extension set 60 cm.
TEST
BUTTON
CHARGE
LED
FAULT
LED
LAMP
FAULT
LED
INDICATION LEDs
L N
220-240V AC/50-60Hz