olympia electronics BSR-6057/A User manual

ADDRESSABLE OPTICAL SMOKE AND THERMAL DETECTOR
103 (diam.) x 48 (height) mm
Alarm LED/to external LED driver (BS-572)
A2S
o
0.120dB/m and 60 C
IP 20
EN 54-5, EN 54-7
o
-10 to 60 C
Up to 95%
2 years
160gr.
TECHNICAL CHARACTERISTICS
BSR-6057/A
IDLE STATE POWER CONSUMPTION
ALARM POWER CONSUMPTION
SENSITIVITY
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
DEGREES OF COVER PROTECTION
OPERATION VOLTAGE
RELATIVE HUMIDITY
TYPICAL WEIGHT
EXTERNAL DIMENSIONS
GUARANTEE
INDICATORS/OUTPUT
CLASS
921605700_09_010
Page 1 from 3
21-28V DC
1.5 mA (with indication LED activated)
1mA
GENERAL
Before installing the detector, the user must read
these instructions carefully and store this manual
for future reference.
BSR-6057/A is an addressable optical smoke
and thermal detector. It co-operates with BSR-
1116 and BSR-2100 panels. The device
transmits an analogue value to the panel which
depends on the amount of the smoke that there is
in the area. The analogue value is 100 with
obscuration rate 0.120dB/m (small amount of
smoke).
The factory setting of the panel is to issue an
alarm when the analogue value is greater than
110.
The user can change from the panel this
analogue value from 100 (high sensitivity) up to
120 (low sensitivity).
o
At the temperature of 60 C the thermal detector
is activated and gives an 120 value.
They have two parts, one plastic base which is
installed on the ceiling and the main unit of the
detector which is fastened to the base by a
simple turning to the right.
The detectors have an indication led which
lights continuously in case of fire detection until
there is a reset signal from the panel. When we
silence the sirens the LED remains lit to show us
the detector that issued the alarm. The LED goes
off when we RESET the panel. The indication led
also flashes every 8 sec to indicate good
operation.
ADDRESS SETTING
To set each detector’s address you have to use
the device BSR-2143 photo. 1. (refer to it’s
instruction manual). After the address setting
mark this number to the sticker on the detector’s
base (ADR:XXX). Each detector must have an
address with which it is recognized from the panel.
It`s forbidden for two devices with same
addresses to be connect to the same loop.
OPERATION CHECK
The operation check can be done by spraying a
small amount of smoke into the detector’s
chamber. You can use the special smoke device
A-752 of our company, or a similar device.
It is advised to conduct a good operation test
every 6 months and every time the detector
position is changed.
It is essential to have good air circulation inside
the detector. Therefore care must be taken so
that the vents of the detector are not covered.
NOTE
The detectors must be placed in the ceiling on
visible areas with no side obstacles and away
from sides with no air circulation or strong air
currents and vapors. Each detector covers almost
2
50 m and the distance between two detectors
must not exceed 15m. Also the detectors must be
placed away from fluorescent tubes at least 50
cm.
The cables cross section must be from 0.5 to
2
1.5mm .
ATTENTION!!
After the device is installed, care must be taken,
so that the detector vents are not blocked by
anything (i.e. dust, paint). Failing to do so will
prevent the smoke particles to enter the
detection chamber.
A f t e r th e i ns t a ll a t i on , it i s t h e so l e
responsibility of the user to maintain the
detector for good operation.
Congratulations for your selection to buy this product.
Olympia Electronics - European manufacturers.

921605700_09_010921605700_09_010 Page 3 from 3Page 2 from 3
1. Detach the detector from it’s base by turning it anticlockwise until the side marks are aligned.
2. Install the base with the included mounting parts (point 5).
3. Connect the power cables (respect to polarity) according to the installation requirements (figure
1,2).
4. Place carefully the detector, so as to align the side marks and turn it clockwise all the way.
Power the device and after 3-5 seconds will be ready to operate.
CONNECTION
1. IN-OUT -L : It is connected to the loop’s (-L).
2. IN +L : It is connected to the loop’s (+L).
3. OUT +R and -R : It is connected with BS-572.
figure 2. photo. 1.
+L -L +L -L
AP
1 2 3 4 5 6 7 8
ON
Loop Loop Loop
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
Loop
Address seting
with BSR-2143
(refer to it’s
instuction manual)
Mounting base
Figure 1.
55
R
+
-R
O
U
T
-
-
L
N
I
T
+
U
R
O
N
+
L
I
Installation procedure
2
Indication marks
Connection
with external
LED BS-572
1
Indication
LED
s
t
e
n
a
f
u
n
n
e
f
t
a
s
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60061 Greece
www.olympia-electronics.gr
[email protected]
BSR-6057/A ADDRESSABLE
RATE OF RISE HEAT DETECTOR
0848-CPR-018 15
EN-54-5: 2000 + A1: 2002
EN-54-7: 2000 + A1: 2002 + A2: 2006
0848
KOLINDROS PIERIAS
60061 GREECE
Certification
The Addressable rate of rise heat detetor
BSR-6057/A is certified from
H.E.E.Q.A.C.
Also H.E.E.Q.A.C. controls the production
under CPR number: