olympia electronics BS- 660/A User manual

Page 1 from 4 921660004_09_003
BS- 660/A
GENERAL
The user have to read carefully the following instructions, in order to be properly informed and
keep them for future use.
The BS-660/A is a conventional heat detector which integrates the function of rate-of-rise
o
heat detection. The detector transitions to alarm state when the temperature reaches 57 C.
o
Also, the detector transitions to alarm state when the temperature rises suddenly by 32 C
regardless of the initial temperature at the beginning of the sudden rise event.
They are composed by two parts. A plastic base which is placed on the ceiling and the main
body of the detector which fits on the plastic base with a simple rotation to the right. The
o
detectors have a 360 visible led and a remote led driver which are light up constantly in case
of detection of fire, till cancelled from the panel. They are turned off only when a reset
command is given from the panel. The indicator led blinks every 6 sec indicating the normal
function.
INSTALLATION
The detectors should be placed in the ceiling in visible points without side obstacles, away
from places that are barely ventilated or with strong air currents and water vapor. Each
2
detector covers an area of 50 m while the distance between two detectors should not be
more than 15m. Also, they must be placed at least 50 cm away from fluorescent lamps. Cable
diameter should be from . to .0 5 2 5mm.
MAINTENANCE & FUNCTIONAL TESTING
The detector has fault diagnosis function, which automatically informs you through the
onboard LED when detector replacement is required. The indication LED blinks every 7
seconds. In normal operation it blinks 1 time and if there is a failure it blinks 3 times. These
90μΑ
17-30V DC
IP42
EN 54-5
12mA (with activated onboard LED)
57oC
ABS/PC
143 gr.
103 (d) x 48 (h) mm
1mΑ for 2 sec
A1R
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
OPERATING TEMPERATURE RANGE
RELATIVE HUMIDITY
CONSTRUCTION MATERIALS
EXTERNAL DIMENSIONS
TYPICAL WEIGHT
GUARANTEE
START UP POWER CONSUMPTION
OPERATION VOLTAGE
Thank you for your trust in our products
Olympia Electronics - European manufacturer
CLASS
INDICATORS
OUTPUT
TEMPERATURE SENSITIVITY
STANDBY CONSUMPTION
ALARM CONSUMPTION
TECHNICAL CHARACTERISTICS
Up to 95%
ο
-40 to 70 C
To panel / to external LED driver (BS-572)
Alarm LED
2 years
Rate-of-rise heat detector
Warranty
Warranty
Olympia Electronics guarantees the quality, condition and operation of the goods. The period
of warranty is specified in the official catalogue of Olympia Electronics and also in the
technical leaflet, which accompanies each product. This warranty ceases to exist if the buyer
does not follow the technical instructions included in official documents given by Olympia
Electronics or if the buyer modifies the goods provided or has any repairs or re-setting done
by a third party, unless Olympia Electronics has fully agreed to them in writing. Products that
have been damaged can be returned to the premises of our company for repair or
replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not
charge the buyer depending on the reason of defection. Olympia Electronics reserves the
right to charge or not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
Page 4 from 4 921660004_09_003
1293
EN 54-5 19
DoP: 921660004_59_001
EGINIO
PIERIAS
60300
GREECE
BS-660/A
Ra te-o f-ri s e heat d etec tor
19
1293

functions combined with periodic manual testing ensure maximum security level. It is
suggested to carry out a test every 6 months or after a change in the position of the sensor. A
key element of its proper function is the air to be able to freely circulate inside it. So be careful
not to block the openings of the outer cover. Before the manual testing procedure it is
suggested to enable the special “walk in test” mode from the panel.
CAUTION !!
After installation the device must not be covered with dust or be painted or anything else
happen that will block the air to get to the sensor. Special attention must be given during the
installation and the use of the device, since the user assumes full responsibility for proper
operation afterwards.
Also, during site works place the plastic cover to the detector as shown in the picture below to
protect the device from dust.
Additional features of the device :
- Integration of dynamic algorithms for noise and false alarm rejection.
- Automatic fault diagnosis.
- 360
ooptically visible LED.
UID:
In every device there is a double sticker with the UID (Unique Identifier) number. This
number is unique for each device.
Page 2 from 4 921660004_09_003
1. Remove the detector from its base rotating to the left till the side marks are aligned.
2. Fasten the base with the supplied mounting materials (point 5).
3. Connect the power cables (minding the correct polarity) according to the requirements of
the installation (Figure 1, 2).
4. Place the detector carefully so that the side marks are on the same position and rotate the
detector clockwise until it locks. Power the device and after 3-5 seconds it is ready for
operation.
CONNECTION
1. + IN/OUT : It is connected to the zone of the panel or to the (+ IN/OUT)
contact of the previous detector.
2. - IN : It is connected to the zone of the panel or to the (- OUT) contact of the
previous detector.
3. - OUT : It is connected to the next detector (- IN) or if it is the last one to the terminal
resistor.
4. - R : It is connected with BS-572.
5. : Connected to the cable’s shield (when shield is used).
Installation process
Installation process
-R
U
T
/O
N
I
+
N
- I
T
U
- O
-R
U
T
/O
N
I
+
N
- I
T
U
- O
Connection
If the power of the detectors is turned off, wait for 3-5 seconds before you turn the power on
again.
Ter mina ting
resistor
Figure 2
From zone
of the panel
Mounting base
Figure 1
2
Connection
with exterrnal
LED
Page 3 from 4
55
R
+
-R
U
T
/O
N
I
+
N
- I
T
U
- O
Side marks
e
n
i
t
n
s
g
a
f
d
t
e
n
t
a
e
c
m
h
1
Indicating
LED
921660004_09_003