olympia electronics BSR-6060/A User manual

ADDRESSABLE RATE OF RISE HEAT DETECTOR
103 (diam.) x 48 (height) mm
Alarm LED
A2R
IP20
EN 54-5
o
-10 to 55 C
Up to 95%
2 years
145gr.
TECHNICAL CHARACTERISTICS
BSR-6060/A
IDLE STATE POWER CONSUMPTION
ALARM POWER CONSUMPTION
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
DEGREES OF COVER PROTECTION
OPERATION VOLTAGE
RELATIVE HUMIDITY
TYPICAL WEIGHT
EXTERNAL DIMENSIONS
GUARANTEE
INDICATORS
CLASS
Page 1 from 3
21-28V DC
1.5 mA (with indication LED activated)
1mA
GENERAL
Before installing the detector, the user must
read these instructions carefully and store this
manual for future reference.BSR-6060/A is a
the r mal and rat e of ris e de t ect o r
simultaneously. It co-operates with BSR-2104
and BSR-2114 panels.
The device transmits an analogue value to the
panel which depends of the area’s
temperature and the rate of temperature rise.
o
The analogue value is 100 (temperature 56 C)
and increases one unit per degree of the
temperature increase. If the temperature rises
o
rapidly (over 5 C per minute) then the
analogue value that sends the detector to the
panel is 127. Analogue value setting 100 is
approved to EN 54-5: 2000 + A1: 2002.
The detector have two parts, one plastic base
which is installed on the ceiling and the main
unit of the detector which is fastened to the
base by a simple turning to the right.
The detectors have an indication led which
lights continuously in case of fire detection
until there is a reset signal from the panel.
When we silence the sirens the LED remains
lit to show us the detector that issued the
alarm. The LED goes off when we RESET the
panel. The indication led also flashes every 8
sec to indicate good operation.
ADDRESS SETTING
To set each detector’s address you have to
use the device BSR-2143 photo. 1. (refer to
it’s instruction manual). After the address
setting mark this number to the sticker on the
detector’s base (ADR:XXX). Each detector
must have an
address with which it is recognized from the
panel.
It`s forbidden for two devices with same
addresses to be connect to the same loop.
OPERATION CHECK
It is advised to conduct a good operation test
every 6 months and every time the detector
position is changed.
It is essential to have good air circulation inside
the detector. Therefore care must be taken so
that the vents of the detector are not covered.
NOTE
The detectors must be placed in the ceiling on
visible areas with no side obstacles and away
from sides with no air circulation or strong air
currents and vapors. Each detector covers
2
almost 50 m and the distance between two
detectors must not exceed 15m.
The cables cross section must be from 0.5 to
2
1.5mm .
ATTENTION!!
After the device is installed, care must be
taken, so that the detector vents are not
blocked by anything (i.e. dust, paint). Failing to
do so will prevent the air to enter the detector.
After the installation, it is the sole
responsibility of the user to maintain the
detector for good operation
921606002_09_014 R_01
Thank you for your trust in our products.
Olympia Electronics - European manufacturer.

Page 3 from 3Page 2 from 3
1. Detach the detector from it’s base by turning it anticlockwise until the side marks are aligned.
2. Install the base with the included mounting parts (point 5).
3. Connect the power cables (respect to polarity) according to the installation requirements (figure
1,2).
4. Place carefully the detector, so as to align the side marks and turn it clockwise all the way.
Power the device and after 3-5 seconds will be ready to operate.
CONNECTION
1. IN-OUT -L : It is connected to the loop’s (-L).
2. IN +L : It is connected to the loop’s (+L).
3. OUT +R and -R : It is connected with external LED BS-572.
figure 2. photo. 1.
+L -L +L -L
AP
1 2 3 4 5 6 7 8
ON
Loop Loop Loop
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
Loop
Address seting
with BSR-2143
(refer to it’s
instuction manual)
Mounting base
Figure 1.
55
R
+
-R
O
U
T
-
-
L
N
I
T
+
U
R
O
N
+
L
I
Installation procedure
2
Indication marks
Connection with
external LED
BS-572
Certification
The Addressable rate of rise heat
detector BSR-6060/A is certified
from H.E.E.Q.A.C and
LPCB(1010d/02). Also
H.E.E.Q.A.C. controls the
production under CPR number:
BSR-6060/A ADDRESSABLE
RATE OF RISE HEAT DETECTOR 0848
EGINIO PIERIAS
60300 GREECE
1
u
n
n
e
f
t
a
s
Indication
LED
s
t
e
n
a
f
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of
warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,
which accompanies each product. This warranty ceases to exist if the buyer does not follow the
technical instructions included in official documents given by Olympia Electronics or if the buyer
modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia
Electronics has fully agreed to them in writing. Products that have been damaged can be returned to
the premises of our company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge
the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or
not the buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Eginio Pierias Greece
www.olympia-electronics.gr
[email protected]
0848-CPR-009 15
EN-54-5: 2000 + A1: 2002
921606002_09_014 R_01921606002_09_014 R_01