olympia electronics BSR-6060/A User manual

ADDRESSABLE RATE OF RISE HEAT DETECTOR
103 (diam.) x 48 (height) mm
Alarm LED
A2R
5 °C / min
IP 20
EN 54-5
o
-10 to 60 C
Up to 95%
2 years
145gr.
TECHNICAL CHARACTERISTICS
BSR-6060/A
IDLE STATE POWER CONSUMPTION
ALARM POWER CONSUMPTION
SENSITIVITY
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
DEGREES OF COVER PROTECTION
OPERATION VOLTAGE
RELATIVE HUMIDITY
TYPICAL WEIGHT
EXTERNAL DIMENSIONS
GUARANTEE
INDICATORS
CLASS
Page 1 from 2
18-30V DC
1.5 mA (with indication LED activated)
1mA
Thank you for purchasing this product of
O l y m p i a E l e c t r o n i c s . A E u r o p e a n
manufacturer.
GENERAL
Before installing the detector, the user must
read these instructions carefully and store
this manual for future reference.BSR-
6060/A is a thermal and rate of rise detector
simultaneously. It co-operates with BSR-
1116 and BSR-2100 panels.
The device transmits an analogue value to
the panel which depends of the area’s
temperature and the rate of temperature
ris e. The an alogu e valu e is 10 0
o
(temperature 56 C) and increases one unit
per degree of the temperature increase. If
o
the temperature rises rapidly (over 5 C per
minute) then the analogue value that sends
the detector to the panel is 128. The factory
setting of the panel is to issue an alarm when
the analogue value is greater than 104. The
panel issues an alarm if the temperature
rises rapidly or if the temperature exceeds
o
the 60 C.The user can change this analogue
o o
value from 100(56 C) up to 120(76 C).
The detector have two parts, one plastic
base which is installed on the ceiling and the
main unit of the detector which is fastened to
the base by a simple turning to the right.
The detectors have an indication led which
lights continuously in case of fire detection
until there is a reset signal from the panel.
When we silence the sirens the LED remains
lit to show us the detector that issued the
alarm. The LED goes off when we RESET the
panel. The indication led also flashes every 8
sec to indicate good operation.
To set each detector’s address you have to
use the device BSR-2143 photo. 1. (refer to
it’s instruction manual). After the address
setting mark this number to the sticker on the
detector’s base (ADR:XXX). Each detector
must have an
address with which it is recognized from the
panel.
It`s forbidden for two devices with same
addresses to be connect to the same loop.
OPERATION CHECK
It is advised to conduct a good operation test
every 6 months and every time the detector
position is changed.
It is essential to have good air circulation
inside the detector. Therefore care must be
taken so that the vents of the detector are not
covered.
NOTE
The detectors must be placed in the ceiling on
visible areas with no side obstacles and away
from sides with no air circulation or strong air
currents and vapors. Each detector covers
2
almost 50 m and the distance between two
detectors must not exceed 15m.
The cables cross section must be from 0.5 to
2
1.5mm .
ADDRESS SETTING
High Quality European based Manufacturers
921606002_23_007

Page 2 from 2
1. Detach the detector from it’s base by turning it anticlockwise until the side marks are aligned.
2. Install the base with the included mounting parts (point 5).
3. Connect the power cables (respect to polarity) according to the installation requirements (figure
1,2).
4. Place carefully the detector, so as to align the side marks and turn it clockwise all the way.
Power the device and after 3-5 seconds will be ready to operate.
CONNECTION
1. IN-OUT -L : It is connected to the loop’s (-L).
2. IN +L : It is connected to the loop’s (+L).
3. OUT +R and -R : It is connected with BSR-5072.
figure 2. photo. 1.
ATTENTION!!
After the device is installed, care must be
taken, so that the detector vents are not
blocked by anything (i.e. dust, paint). Failing
to do so will prevent the smoke particles to
enter the detection chamber.
After the installation, it is the sole
responsibility of the user to maintain
the detector for good operation.
+L -L +L -L
AP
1 2 3 4 5 6 7 8
ON
Loop Loop Loop
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
-R
O
U
T
-
-
N
L
I
+
U
T
R
O
+
L
I
N
Loop
Address seting
with BSR-2143
(refer to it’s
instuction manual)
Mounting base
Figure 1.
55
R
+
-R
O
U
T
-
-
L
N
I
T
+
U
R
O
N
+
L
I
Installation procedure
2
Indication marks
Connection with
external LED
BSR-5072
921606002_23_007
s
t e
n
a
f
u
n
n
e
f
a
t
s
1
Indication
LED