Olympus SOLTIVE Premium User manual

SuperPulsed Laser System
Quick Reference Guide
SOLTIVE™ Premium / Pro

2SOLTIVE™ Premium / Pro Quick Reference Guide
This guide is designed as a quick reference guide only.
It is not a substitute for reading the entire User Manual
and/or Instructions for Use (IFU) provided with the SOLTIVE
Premium or SOLTIVE Pro SuperPulsed laser system.
Olympus does not encourage or recommend any actions
that are considered off-label. For a complete list of
indications, contraindications, warnings & precautions,
please refer to the SOLTIVE User Manual.

SOLTIVE™ Premium / Pro Quick Reference Guide 3
Required parts
Power Cord
Footswitch (wired or wireless)
Laser Fiber
Interlock Connector
Blast Shield
1
2
3
4
5
Power Cord
TFL-APCUS
Laser Fiber
See last page for all SKUs
Interlock Connector
TFL-AIC
Blast Shield
TFL-ABS
Footswitch (wired or wireless)
TFL-AFSW (wired) TFL-AFSWL (wireless)
Laser Set-Up
1 2
3 4 5

4SOLTIVE™ Premium / Pro Quick Reference Guide
Laser Set-Up
Auxiliary Screen,
Swivel LCD Display
(Premium Only)
Laser Port,
closed via
Dust Shield LCD
Display
Emergency
Stop Button
Power
Button

SOLTIVE™ Premium / Pro Quick Reference Guide 5
Laser Set-Up
Connect power cord
nVisually inspect the power cable for any tears or cracks, do not use
if it appears to be damaged in any way. Connect the female end of
the plug into the power port on the rear side of the laser system.
nPlug the power cable into a standard wall outlet; use a medical grade
extension cord if the supplied power cord does not provide an adequate
length to position the unit.
nWhen moving the laser system, always remove the power cord.
Wrap and store the cord in a drawer or a cord wrap on the cart.
Power
Cable
External
Fuses (2)
HDMI for
Video Cable
Remote Interlock
Connector
USB (2)
Potential
Equalization
Conductor
Wired Foot Switch
Connection

6SOLTIVE™ Premium / Pro Quick Reference Guide
Press the on button and start the device
nEnsure all persons in the treatment room are wearing the appropriate laser
safety eyewear prior to turning on the laser system. The laser beam
emitted by the SOLTIVE™ SuperPulsed Laser System may injure the eye.
– Use protective goggles with the following minimal specifications:
1910-1970 | LB3 for laser source Thulium at 1920 – 1960 nm.
– In addition, do not look directly at the laser beam, even when
wearing protective goggles.
nMake sure the red emergency stop
button (circled in the figure to the right)
is not pressed. To reset the button, turn
the knob either direction until it releases
into the original position.
nPress the power button on the
front panel to turn ON the system.
When the button is pressed, the
LED lights up to indicate that the
laser system is turned on. The initial
screen will present the company
logo, followed by the Login screen.
nEnter the default
passcode to begin.
(Default Passcode: 1234)
The Home Screen will load
once unlocked.
Laser Operation

SOLTIVE™ Premium / Pro Quick Reference Guide 7
Pair the wireless footswitch
nPlace the wireless footswitch near the device.
nTo begin pairing from the Home screen enter System Setup via the
Settings screen. Note the footswitch icon indicated with a crossed line
when not paired. To pair the footswitch to the laser system, place the
footswitch in the vertical position. Tap Continue when ready.
nPress the button on the back of the footswitch for 3-6 seconds and then
tap Continue. Successful pairing will be indicated on the screen.
nAlternatively, if using the wired footswitch,
connect the cable in the rear of the laser
system into the footswitch connector port,
circled in the figure to the right. Pairing is
not needed with the wired footswitch.
Laser Operation

8SOLTIVE™ Premium / Pro Quick Reference Guide
Connect the laser fiber
nThe laser fiber is connected to the laser
system through a customized fiber
connector. The laser will only emit laser
energy if the system detects a valid laser
fiber.
nThe optical fiber port on the front of the
laser system senses the presence of a laser
fiber and will automatically open when the
laser fiber connector is brought into close
range.
nOnce the door opens, insert the sterile surgical fiber by advancing the
fiber connector straight into the port. Once inserted, surgical fibers are
automatically detected by the system. Fibers do not need to be screwed
into the port.
View fiber information
nThe Fiber Information panel appears
by pressing on the Fiber Info area
on the Settings screen.
nWhen viable surgical laser fibers are
inserted into the laser port, the system
will detect the following information:
– Fiber type
– Fiber core diameter
– Fiber uses remaining. Note: a fiber use is counted once laser energy
is passed through the fiber.
Laser Operation

SOLTIVE™ Premium / Pro Quick Reference Guide 9
Adjust the aiming beam
nSelect the aiming beam button
on the treatment screen.
nThe following screen allows the aiming
beam intensity to be adjusted. The
aiming beam provides three options:
blinking emission, continuous
emission, no emission.
Laser parameter adjustment
nSelect the appropriate treatment,
preset, or manual mode from
on the Home Screen.
nPress the touch screen to adjust
the parameters on a selected mode.
nAdjust the Pulse Energy or Frequency
to match the desired clinical effect
by sliding your finger over the
parameter, tapping the -/+ buttons,
or holding down the -/+ buttons.
nThere are three options for Pulse
Width: long, medium, or short. Select the desired Pulse Width by
pressing the Pulse Width indicator button to toggle between settings.
nSelect the Home button to choose a different treatment mode.
Laser Operation

10 SOLTIVE™ Premium / Pro Quick Reference Guide
Standby/Ready
nTo enter Ready Mode from Standby Mode, press the Ready button
on the Treatment Screen, or press the central button (Ready/Standby)
on the footswitch.
nAn audible tone will be heard when transitioning between Standby
and Ready modes
Activating the laser
nOnce the Ready button is pushed, there is a 2 second delay before
the laser is ready to emit. The footswitch will activate emission.
nThe left and right foot pedals coincide with the left and right sections of
the treatment screen. Each foot pedal can have a different setting
to customize laser performance.
Left pedal emits laser parameters
shown on left side of touch screen.
Right pedal emits laser parameters
shown on right side of touch screen.
Laser Operation
Standby Mode
Screen will transition from blue
to green indicating ready to use.
Ready status is highlighted
by green numerals and button.
Ready Mode
Ready/Standby Button