Omron E5CC User manual

60ҹϞ
45
45
+0.6
0
+0.6
0
+0.6
0
˄48hܗ᭄䞣 - 2.5˅
+1
0
45
㸼⼎┰೼ⱘ䰽ᚙމˈབϡࡴҹ䰆ℶˈᕜৃ㛑ᇐ㟈䕏
ᑺ៪ЁᑺⱘҎ䑿Ӹᆇ៪䋶ѻᤳണDŽ೼Փ⫼䆹ѻકࠡᑨ
Ҩ㒚䯙䇏ᴀ᠟ݠDŽ
E5CC
᭄ᄫᓣ᥻ࠊ఼
䇋ࡵᖙ䙉ᅜҹϟ⊼ᛣџ乍ˈҹ䙓ܡ᪡԰༅ǃ䇃ࡼ԰៪ᇍѻક⡍ᗻঞࡳ㛑䗴៤ϡ㡃ᕅડDŽ৺߭ˈৃ㛑Ӯᇐ㟈ᛣ
໪џᬙDŽ䇋೼ᣛᅮ㣗ೈݙՓ⫼ᴀѻકDŽ
˄1˅ 䆹ѻકা㹿䆒䅵ЎᅸݙՓ⫼DŽ䇋࣓೼ᅸ໪Փ⫼DŽϡ㽕೼ҹϟӏԩഄᮍՓ⫼៪ᄬᬒ䆹ѻકDŽ
gⳈ᥹ফࡴ⛁䆒໛⛁䕤ᇘⱘഄᮍDŽ
g᳝⎆ԧ៪⊍⇨亲⑙ⱘഄᮍDŽ
g䰇ܝⳈᇘⱘഄᮍDŽ
g♄ᇬ䕗໮៪᳝㜤㱔ᗻ⇨ԧ˄⡍߿ᰃ⸿࣪⠽⇨ԧ⇼⇨˅ⱘഄᮍDŽ
g⏽ᑺ࠻⚜ব࣪ⱘഄᮍDŽ
g㒧ބ㒧䴆ⱘഄᮍDŽ
g᳝䳛ࡼ៪໻ⱘކߏⱘഄᮍDŽ
˄2˅ ೼乱ᅮⱘ⏽ᑺ⑓ᑺ㣗ೈݙՓ⫼/ᄬټ䆹䆒໛DŽᖙ㽕ᯊᑨ䞛পᔎࠊދDŽ
˄3˅ Ў߽Ѣᬷ⛁ˈϡ㽕฿า䆹ѻકೈⱘぎ䯈DŽ
ϡ㽕ฉาѻકⱘ䗮亢ᄨDŽ
˄4˅ ᣝッᄤⱘᵕᗻ䖯㸠ℷ⹂ⱘ᥹㒓DŽ
˄5˅ 䇋Փ⫼㾘ᅮሎᇌ˄M3ˈᆑᑺᇣѢ៪ㄝѢ5.8 mm˅ⱘ᥹ッᄤ䖯㸠᥹㒓DŽՓ⫼󰵼᳝AWG24AWG18˄Ⳍ
ᔧѢ῾៾䴶⿃0.2050.8231 mm2˅ⱘ䪰㒲㒓៪ᅲᖗ⬉㓚䖲᥹㻌㒓᥹㒓ᵓDŽ˄࠹㒓䭓ᑺЎ68 mmDŽ˅
ϔϾッᄤݙ᳔໮ᦦܹϸḍⳌৠൟোሎᇌⱘᇐ㒓៪᥹ッᄤDŽ
˄6˅ ϡ⫼ⱘッᄤϡ㽕᥹㒓DŽ
˄7˅೼᥻ࠊ఼Ϣৃҹѻ⫳催乥⌾⍠ⱘ䆒໛П䯈ᑨֱᣕ䎇໳䖰ⱘ䎱⾏DŽᇚ催៪໻⬉⌕⬉⑤㒓Ϣ݊ᅗᇐ
㒓䱨⾏ˈ೼ッᄤ᥹㒓ᯊ䙓ܡϢ⬉⑤㒓݅ッ៪ᑊ㘨DŽ
˄8˅ ೼乱ᅮ䋳䕑կ⬉⬉⑤ϟՓ⫼䆹ѻકDŽ
˄9˅Փ⫼ᓔ݇៪㒻⬉఼㾺⚍ҹ⹂ֱ೼ϸ⾦ݙᇚ⬉⑤Ў乱ᅮ⬉DŽབᵰ⬉ᰃ䗤⏤Ϟⱘˈ⬉⑤ৃ㛑᮴
⊩໡ԡ៪㗙থ⫳䕧ߎ䇃ࡼ԰DŽ
˄10˅೼᥹䗮⬉⑤ࠄᓔྟᅲ䰙᪡԰ࠡᑨ⹂ֱ᥻ࠊ఼䖯㸠30ߚ䩳ҹϞⱘ乘⛁ˈҹֱ䆕ℷ⹂ⱘ⏽ᑺᰒ⼎DŽ
˄11˅ᠻ㸠㞾󰶖ℷᯊˈ䇋ৠᯊ᥹䗮䋳䕑䆒໛៪㗙೼᥹䗮᥻ࠊ఼ࠡ᥹䗮䋳䕑DŽ
˄12˅೼䆹ѻકⱘ䰘䖥ᑨ䆹᳝ᓔ݇៪㗙ᮁ䏃఼DŽᓔ݇៪㗙ᮁ䏃఼ᑨ䆹೼᪡԰㗙֓Ѣ໳ࠄⱘഄᮍˈᑊϨ᳝ᯢᰒ
ⱘᮁᓔ󰵼ᖫDŽ
˄13˅
⏙⋕ᯊˈ䇋⫼ᑆⱘ䕃Ꮧ󰩛ᣁDŽ䇋࣓Փ⫼⿔䞞ࠖǃ≑⊍ǃ䜦㊒ㄝ৿⒊ࠖⱘ㥃કDŽ৺߭Ӯᇐ㟈বᔶ៪ব㡆DŽ
˄14˅೼䆒䅵㋏㒳˄བ᥻ࠊ䴶ᵓ˅ⱘᯊ׭ˈ䳔㽕㗗㰥ࠄ᥻ࠊ఼ⱘ䕧ߎ೼⬉⑤Ϟ⬉ৢ᳝2⾦ⱘᓊᯊDŽ
˄15˅ᔧߛᤶࠄ߱ྟ䆒ᅮ㦰ᯊˈ䕧ߎৃ㛑Ӯ݇䯁DŽ೼ᅲᮑ᥻ࠊᯊ䳔㽕㗗㰥ࠄ䖭ϔ⚍DŽ
˄16˅䴲᣹থݙᄬⱘݭ󱂖᭄ᰃ᳝䰤ⱘDŽ᠔ҹ೼䗮ֵ៪݊ᅗ᪡԰䳔㽕乥㐕䞡ݭ᭄᥂ᯊˈ䇋Փ⫼RAMݭ῵ᓣDŽ
˄17˅ᢚ᥻ࠊ఼䖯㸠ᑳᓗ໘⧚ᯊˈ䇋Փ⫼䗖ᔧⱘᎹ݋DŽ
˄18˅䇋࣓䍙䖛㾘ḐЁ㒭ߎⱘ䗮ֵ䎱⾏ᑊՓ⫼ᣛᅮⱘ䗮ֵ⬉㓚DŽ᳝݇䗮ֵ䎱⾏⬉㓚㾘Ḑˈ䇋খ䯙lj(ƶ&᭄
ᄫᓣ᥻ࠊ఼⫼᠋᠟ݠNJ˄&DW1R+˅DŽ
˄˅䖲᥹њ86%㋏߫䕀ᤶ⬉㓚ᯊˈ䇋࣓ᓔǃ݇᥻ࠊ఼ⱘ⬉⑤DŽ৺߭Ӯᇐ㟈᥻ࠊ఼ᬙ䱰DŽ
˄˅ッᄤৄ⏽ᑺ催䖒ćˈ䇋໮ࡴᇣᖗDŽ
ᅝܼՓ⫼⊼ᛣџ乍
᳝݇䆺㒚ⱘᑨ⫼ℹ偸ˈ䇋খ䯙ljE5ƶC᭄ᄫᓣ᥻ࠊ఼⫼᠋᠟ݠNJ
˄Cat. No. H180˅DŽ
Փ⫼䇈ᯢк
ᛳ䇶ᙼ䌁ф󱂜ྚ啭E5CC᭄ᄫᓣ᥻ࠊ఼DŽ
ᴀ᠟ݠᦣ䗄њѻકⱘࡳ㛑ǃᗻ㛑ҹঞՓѻક䖒ࠄ᳔ՇՓ⫼ᬜ
ᵰⱘᑨ⫼ᮍ⊩DŽ
䇋೼Փ⫼䆹ѻકᯊ⊼ᛣҹϟџ乍˖
gՓ⫼䆹ѻકⱘҎᖙ乏݋໛䎇໳ⱘ⬉⇨㋏㒳ⶹ䆚DŽ
g೼Փ⫼䆹ѻકࠡᑨ䗮䇏ᑊ⧚㾷ᴀ᠟ݠҹ⹂ֱℷ⹂ⱘՓ⫼DŽ
gཹ୘ֱㅵ䆹᠟ݠҹ⹂ֱ೼䳔㽕ᯊৃҹ䱣ᯊᶹ䯙DŽ
󱂜ྚ啭݀ৌ
©All Rights Reserved
᳝݇催㑻ࡳ㛑䆒ᅮ㦰ǃ᠟ࡼ᥻ࠊ㦰ҹঞ݊ᅗࡳ㛑ⱘֵᙃˈ䇋খ㗗
ljE5ƶC᭄ᄫᓣ᥻ࠊ఼⫼᠋᠟ݠNJ˄Cat. No. H180˅DŽ
᳝݇䗮ֵⱘ䆺㒚ֵᙃˈ䇋খ䯙ljE5ƶC᭄ᄫᓣ᥻ࠊ఼䗮ֵ᠟ݠNJ
˄Cat. No. H181˅DŽ
կ⬉⬉ 100240 VACˈ50/60 Hz៪㗙
24 VACˈ50/60 Hz/24 VDC
Ꮉ԰⬉㣗ೈ 乱ᅮ⬉ⱘ85110%
ࡳ⥛⍜㗫
䗝乍000: ᳔໻5.2 VA˄AC100-240V˅
᳔໻3.1 VA˄AC24V˅/᳔໻1.6 W˄DC24V˅
᠔᳝݊ᅗ㾘Ḑ˖ ᳔໻6.5 VA˄AC100-240V˅
᳔໻4.1 VA˄AC24V˅/᳔໻2.3 W˄DC24V˅
ᣛ⼎㊒ᑺ ⛁⬉ي䕧ܹ˖
˄⦃๗⏽ᑺ˖23°C˅˄ᰒ⼎ؐⱘ±0.3%៪㗙±1°CЁⱘ䕗໻ؐ˅
᳔໻±1ԡ᭄
䪖⬉䰏䕧ܹ˖
˄ᰒ⼎ؐⱘ±0.2%៪㗙±0.8°CЁⱘ䕗໻ؐ˅
᳔໻±1ԡ᭄
῵ᢳ䞣䕧ܹ˖
±0.2 % FS ᳔໻±1ԡ᭄
џӊ䕧ܹ 䕧ߎ⬉⌕˖↣Ͼ㾺⚍㑺7 mADŽ
㾺⚍䕧ܹ ON˖᳔໻1 k:ˈOFF˖᳔ᇣ100 k:
䴲㾺⚍䕧ܹ ON˖⅟ԭ⬉᳔໻1.5 V
OFF˖ⓣ⬉⌕᳔໻0.1 mA
䖰⿟SP䕧ܹ 420 mA DC៪020 mA DC
05 VDC៪15 VDC៪010 VDC
᥻ࠊ䕧ߎ1 㒻⬉఼䕧ߎ˖SPST-NO
250 VACˈ3 A˄䰏ᗻ䋳䕑˅
㒻⬉఼⬉⇨ᇓ˖100,000󱂖䖤㸠
⬉䕧ߎ˄⫼Ѣ偅ࡼSSR˅˖
12 VDC ±20%ˈ21 mA
⬉⌕䕧ߎ˖420 mA DCˈ020mA DC
䋳䕑˖᳔໻500 :
᥻ࠊ䕧ߎ2 ⬉䕧ߎ˄⫼Ѣ偅ࡼSSR˅˖
12 VDCˈ21 mA
᥻ࠊᮍ⊩ ON/OFF៪2䏃PID᥻ࠊ
䕙ࡽ䕧ߎ 㒻⬉఼䕧ߎ˖SPST-NOˈ250 VACˈ
2Ͼ䕧ߎ˖3 A˄䰏ᗻ䋳䕑˅
3Ͼ䕧ߎ˖2 A˄䰏ᗻ䋳䕑˅
㒻⬉఼⬉⇨ᇓ˖100,000󱂖䖤㸠
䕀ᤶ䕧ߎ 420 mA DCˈ᳔໻䋳䕑500 :
15 VDCˈ᳔ᇣ䋳䕑1 k:
⦃๗⏽ᑺ -1055°C
˄ᑨ䙓ܡ㒧ބ៪㒧䴆˅
⦃๗⑓ᑺ RH 2585%
ᄬټ⏽ᑺ -2565°C
˄ᑨ䙓ܡ㒧ބ៪㒧䴆˅
催ᑺ ᳔催2,000㉇
᥼㤤ֱ䰽ϱ T2Aˈ250 VACˈᯊᓊˈԢ❨ᮁᆍ䞣
䞡䞣 㑺120 g˄ҙ᥻ࠊ఼˅
䰆ᡸㄝ㑻 ࠡ䴶ᵓ˖IP66
ৢ໇˖IP20ˈッᄤ˖IP00
ᅝ㺙⦃๗ ᅝ㺙⾡㉏IIˈ∵ᶧ
ㄝ㑻2˄IEC61010-1˅
ݙᄬֱᡸ 䴲᣹থݙᄬ
˄ݭ󱂖᭄˖1,000,000˅
᱖ᯊ䖛⬉ ⷁᯊ䯈䖛⬉9˄⬉⑤⬉˅
 䭓ᯊ䯈䖛⬉9˄⬉⑤⬉˅
䄺
䄺
䗮⬉ᳳ䯈ˈ䇋࣓㾺ᩌッᄤDŽ
৺߭Ӯ಴㾺⬉㗠ᇐ㟈䕏ӸDŽ
ϡᕫ䅽䞥ሲ⠽ԧǃᇐ㒓៪ᅝ㺙ᯊѻ⫳ⱘߛሥ៪⑓⇨䖯ܹ᥻ࠊ఼ǃ䇗䆩Ꮉ݋ッষ៪䇗䆩Ꮉ݋⬉㓚䖲᥹
఼ⱘᓩ㛮ϞDŽ৺߭Ӯᇐ㟈㾺⬉ǃ☿♒៪ᴎ఼䇃ࡼ԰DŽ
䇋࣓ᇚ䆹ѻક⫼Ѣ᳝ᯧ➗ᯧ⟚⇨ԧⱘഎড়DŽ৺᳝߭ৃ㛑಴Ў⟚⚌㗠䗴៤䕏ᑺӸᆇDŽ
㒱ᇍϡ㽕ᢚǃᬍ㺙ҹঞׂ⧚䆹ѻક៪᥹㾺ӏԩݙ䚼ܗӊDŽ৺߭Ӯᇐ㟈䕏ᖂ㾺⬉ǃ☿♒៪ᴎ఼䇃ࡼ
԰DŽ
⊼ᛣˉ☿♒៪㾺⬉ⱘ䰽
a˅䆹ѻકЎUL䅸䆕ⱘᓔᬒൟ䖛⿟᥻ࠊ䆒໛ˈᖙ乏ᅝ㺙೼㛑໳䰆ℶ☿㢅䗌ߎⱘᴎ໇ЁDŽ
b˅೼Փ⫼ϸϾҹϞᮁ⬉ᓔ݇ⱘᚙމϟˈ㓈ׂࠡ䇋ܜᮁᓔ᠔᳝ᓔ݇ˈ⹂ֱᴀѻક໘Ѣᮁ⬉⢊ᗕDŽ
c˅ֵো䕧ܹЎSELV˄ᅝܼԢ⬉⑤˅ˈಲ䏃ফ䰤DŽ
d˅⊼ᛣ˖Ўњޣᇥ☿♒៪㾺⬉ⱘ䰽ˈ䇋࣓ᇚϡৠⱘ2㉏ಲ䏃ⱘ䕧ߎѦ㘨DŽ
བᵰ䕧ߎ㒻⬉఼䍙䖛њ乘ᳳⱘՓ⫼ᇓˈ᳝ᯊӮথ⫳㾺⚍❨࣪៪➗⚻DŽྟ㒜㽕⊼ᛣ䕧ߎ㒻⬉఼ⱘᑨ
⫼⦃๗ˈᑊ೼乱ᅮ䋳䕑ঞ乘ᳳᇓҹݙՓ⫼DŽ䕧ߎ㒻⬉఼ⱘ乘ᳳᇓ䱣ⴔ䕧ߎ䋳䕑ҹঞᓔ݇ᴵӊⱘ
ব࣪㗠ব࣪DŽ
ᵒࡼⱘ㶎ϱৃ㛑ᇐ㟈☿♒DŽ䇋ҹᣛᅮⱘ0.430.58 Ngmⱘᣛᅮᡁⶽᢻ㋻㶎ϱDŽ
䇋䆒ᅮ䗖ড়㋏㒳᥻ࠊ⫼ⱘѻકখ᭄DŽབᵰ䆒ᅮϡᔧˈৃ㛑Ӯ಴ᛣ໪᪡԰㗠䗴៤䋶ѻᤳ༅៪џᬙDŽ
᥻ࠊ఼䇃ࡼ԰ᕜৃ㛑䗴៤᥻ࠊ᪡԰༅ᬜ៪䰏ℶ᡹䄺䕧ߎˈᇐ㟈䋶ѻᤳ༅DŽЎњ೼᥻ࠊ఼থ⫳䇃ࡼ԰
ᯊ⹂ֱᅝܼˈᑨ䞛প䗖ᔧⱘᅝܼ᥾ᮑˈབՓ⫼⣀ⱘ㒓䏃ᅝ㺙ⲥ᥻䆒໛DŽ
CHN
ᅝܼ⊼ᛣџ乍
䄺ヺোⱘ㽕⚍
ሎᇌ㾘Ḑ
2˖䫭䇃ᰒ⼎া䩜ᇍĀ䖛⿟ؐ/䆒ᅮؐāˈ㗠ϡ䩜ᇍ݊ᅗ⢊ᗕDŽ
ᔧথ⫳ϔϾ䫭䇃ᯊˈ㄀ϔᰒ⼎ᇚᰒ⼎䫭䇃ҷⷕDŽখ㗗ϟ㸼ˈḍ᥂䫭䇃ҷⷕ䞛প䗖ᔧⱘ᥾ᮑDŽ
བᵰ䕧ܹؐ䍙䖛ᰒ⼎㣗ೈ˄-19999999˅ˈՓҡ໘Ѣ᥻ࠊ㣗ೈݙˈԢѢ-1999ⱘᇚᰒ⼎
[[[[ ˈ催Ѣ9999ⱘᰒ⼎
 ]]]] DŽ೼䖭⾡ᚙމϟˈ᥻ࠊ䕧ߎ᡹䄺䕧ߎഛᇚℷᐌᎹ԰DŽ
݇Ѣৃ᥻ࠊⱘ㣗ೈˈ䇋খ䯙ljE5ƶC᭄ᄫᓣ᥻ࠊ఼⫼᠋᠟ݠNJ˄Cat. No. H180˅DŽ
Ẕᶹ䕧ܹ㉏ൟখ᭄ⱘ䆒㕂ˈẔᶹ䕧ܹ᥹㒓ᑊẔᶹ⏽
ᑺӴᛳ఼ᰃ৺ᄬ೼⸈ᤳ៪ⷁ᥹DŽ
݇ᥝ⬉⑤ݡᠧᓔDŽབᵰᰒ⼎ϡবˈ߭乏ׂ⧚᥻ࠊ఼DŽ
བᵰᰒ⼎ᘶ໡ℷᐌˈ߭ৃ㛑ᰃ᥻ࠊ㋏㒳ফࠄ໪䚼ᑆ
ᡄDŽ䇋Ẕᶹ໪䚼ᑆᡄDŽ
㑴ℷA/D䕀ᤶ䫭䇃Пৢˈ݇ᥝ⬉⑤ݡᠧᓔDŽབᵰᰒ
⼎ϡবˈ߭乏ׂ⧚᥻ࠊ఼DŽབᵰᰒ⼎ᘶ໡ℷᐌˈ߭
ᬙ䱰಴ৃ㛑ᰃ᥻ࠊ㋏㒳ফࠄ໪䚼ᑆᡄDŽ䇋Ẕᶹ໪
䚼ᑆᡄDŽ
㄀ϔᰒ⼎ ৿Н
A/D䕀ᤶ䫭䇃
2
ݙᄬ䫭䇃
䕧ܹ䫭䇃
2
s.err˄S. Err˅
e111˄E111˅
᪡԰
OFF
᡹䄺
ߎ䫭⢊ᗕ
OFF
OFF
OFF
OFF
e333˄E333˅
䫭䇃ᰒ⼎˄ᬙ䱰䆞ᮁ˅
䄺ヺো
ᅝ㺙 䖲᥹˄ッᄤ䗖⫼ᗻ಴ᴎ఼ൟো㗠ᓖDŽ˅
㾘Ḑ
݊ᅗࡳ㛑
᥹㒓
ࠡ䴶ᵓⱘܗӊৡ⿄
g°C / °F˖⏽ᑺԡ
ᔧᰒ⼎ݙᆍЎ⏽ᑺᯊᰒ⼎⏽ᑺԡDŽḍ᥂⏽ᑺԡⱘ
䆒ᅮؐᰒ⼎°C៪°FDŽ
g῵ᓣ䬂
ᣝℸ䬂ᬍবᰒ⼎ݙᆍDŽ
ᣝ䆹ᣝ䪂1⾦ҹϞডᮍ৥ᰒ⼎ݙᆍDŽ
gৠᯊᣝԣO䬂M䬂㟇ᇥ3⾦ᴹߛᤶ㟇ֱᡸ㦰DŽ
g㦰䬂
Փ⫼䆹䬂ߛᤶ㦰˖
g⿏ԡ䬂˄PF䬂˅
PF䆒㕂খ᭄咬䅸䆒ᅮЎՓ᭄ԡ⿏ԡDŽℸ䬂Ўࡳ㛑
䬂DŽᔧᣝϟℸ䬂ˈЎPF䆒ᅮখ᭄䆒ᅮⱘࡳ㛑ᇚ⫳
ᬜDŽ
᪡԰㦰
1: 㽕Փখ᭄1ǃ4ǃ5ᦤկϡৠⱘ᡹䄺㉏ൟˈৃᇍ݊䆒ᅮϞ䰤Ϣϟ䰤DŽ
ϟ䰤Ϟ䰤ߚ߿⫼ᄫ↡ LHᣛ⼎DŽ
咬䅸ⱘ᡹䄺㉏ൟЎ“2”
᡹䄺
g˖ֱᡸᣛ⼎
ᔧ䆒ᅮব᳈ֱᡸЎON˄⽕⫼৥Ϟ/৥ϟ䬂˅ᯊ⚍
҂DŽ
gMANU˖᠟ࡼ䕧ߎᣛ⼎
ᔧ㞾ࡼ/᠟ࡼ῵ᓣ䆒ᅮЎ᠟ࡼ῵ᓣᯊ⚍҂DŽ
ৠϞ䗄Ϟ䰤
᡹䄺Ꮉ԰
᥻ࠊ䕧ߎ
CC4
Ƶ㘨㋏ᮍᓣ
ƽࠊ䗴ଚ
ƽᡔᴃ䆶
󱂜ྚ啭Ϟ⍋᳝䰤݀ৌ
ഄഔЁ೑Ϟ⍋Ꮦ⌺ϰᮄ䞥ḹߎষࡴᎹ䞥ঢ়䏃ো
⬉䆱(86)21-50509988
󱂜ྚ啭㞾ࡼ࣪Ё೑᳝䰤݀ৌ
ഄഔЁ೑Ϟ⍋Ꮦ⌺ϰᮄ䫊ජЁ䏃োЁ䫊໻ᅸ
⬉䆱(86)21-5307-2222
ᡔᴃ䆶⛁㒓400-820-4535
㔥ഔhttp://www.fa.omron.com.cn
䗖⫼ᗻ
೼ᅶ᠋ⱘᑨ⫼Ёˈ󱂜ྚ啭ϡ䋳䋷ѻકϢӏԩᅶ᠋ッѻક᠔⍝ঞⱘ㾘Ḑǃ㾘㣗󰵼ޚ
ֱᣕϔ㟈ᗻDŽ䇋ࡵᖙ㗗㰥ᴀѻકᇍѢ᠔ᑨ⫼ⱘ㋏㒳ǃᴎ఼䆒໛䯈ⱘ䗖⫼ᗻDŽՓ⫼
ᯊ䇋⊼ᛣᑊ䙉ᅜᴀѻકⱘ⽕ℶџ乍DŽ
೼≵᳝⹂䅸ᭈϾ㋏㒳䆒䅵ᯊ᠔㗗㰥ࠄⱘ亢䰽ˈҹঞ≵᳝⹂䅸೼䆒໛㋏㒳Ё䆹󱂜ྚ
啭ѻકⱘ乱ᅮՓ⫼ᴵӊℷ⹂ᅝ㺙ᴵӊⱘᚙމϟˈ⽕ℶᇚᴀѻકᑨ⫼ѢᇍҎ䑿ঞ䋶
ѻᄬ೼Ϲ䞡䰽ⱘഎড়DŽ
䆺㾕ѻક㾘ḐкЁֱ䆕ঞܡ䋷џ乍ݙᆍDŽ
䖤㸠ذℶ
˄᥻ࠊ᡹䄺ഛذℶDŽ˅ 5
߱ྟ䆒ᅮ㦰
ᇍ↨՟㓽ᬒ䞛⫼ϟ߫㣗ೈ˖-19999999ǃ
-199.9999.9ǃ-19.9999.99ǃ-1.999
9.999
⬉⌕䕧ܹ
⬉䕧ܹ
῵ᢳ䞣䕧ܹ
㉏ൟ
䇋࣓೼♄㡆ッᄤϞ䖲᥹ӏԩ఼ӊDŽ
ሎᇌ˄mm˅
䗮⬉ПࠡẔᶹ᥹㒓DŽ
1
1
1
᡹䄺㉏ൟ
ḍ᥂LǃHؐ
ⱘϡৠ㗠ϡৠ
ḍ᥂LǃHؐ
ⱘϡৠ㗠ϡৠ
ḍ᥂LǃHؐ
ⱘϡৠ㗠ϡৠ
᮴᡹䄺ࡳ㛑 ᮴䕧ߎ
㒱ᇍؐϞ䰤
㒱ᇍؐϟ䰤
LBA˄ҙᇍ᡹䄺1˅
أᏂϞ/ϟ㣗ೈ
أᏂϞ䰤
أᏂϞ/ϟ䰤
أᏂϟ䰤
᡹䄺䕧ߎࡳ㛑
ℷ᡹䄺ؐ˄X˅ 䋳᡹䄺ؐ˄X˅
䆒ᅮ
PVব࣪⥛᡹䄺
X
ON
OFF SP
X
ON
OFF SP
ON
OFF SP
X
X
ON
OFF SP
LH
ON
OFF SP
X
ON
OFF SP
X
ON
OFF SP
X
ON
OFF 0
ON
OFF
X
0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF
X
0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
LH
ON
OFF SP
SP
ON
OFF
X
ON
OFF
X
0
1
0
2
3
4
5
6
7
8
9
SP㒱ᇍؐϞ䰤
SP㒱ᇍؐϟ䰤
14
15
MV㒱ᇍؐϞ䰤
MV㒱ᇍؐϟ䰤
16
17
RSP㒱ᇍؐϞ䰤
RSP㒱ᇍؐϟ䰤
18
19
10
11
12
13
SP
X
ON
OFF
ON
OFF
X
0
oapt
0
pmov
0
chgp
off
pmsk
on
icpt
1
wtpt
off
pfpt
off
PF䬂ֱᡸ
䰤ࠊPF䬂᪡԰DŽ
䗮⬉
MVⲥ᥻
˄ࡴ⛁˅
6o
0.0
MVⲥ᥻
˄ދ˅
6c-o
0.0
᡹䄺ؐ
ϟ䰤1 4
6al1l
0
᡹䄺ؐ2 4
6al-2
0
᡹䄺ؐ
Ϟ䰤2 4
6al2h
0
᡹䄺ؐ
ϟ䰤2 4
6al2l
0
᡹䄺ؐ3 4
6al-3
0
᡹䄺ؐ
Ϟ䰤3 4
6al3h
0
᡹䄺ؐ
ϟ䰤3 4
6al3l
0
᡹䄺ؐ
ϟ䰤4 4
6al4l
0
᡹䄺ؐ4 4
6al-4
0
᡹䄺ؐ
Ϟ䰤4 4
6al4h
0
䕧ܹ㉏ൟ3
SPϞ䰤
SPϟ䰤
PIDgON/OFF
Փ⫼ON/OFF᥻ࠊᯊ=onof
Փ⫼2䏃PID᥻ࠊᯊ=pid
󰵼ޚ៪ࡴ⛁/ދ
󰵼ޚ᥻ࠊᯊ=stnd
ࡴ⛁ދ᥻ࠊᯊ= h-c
᥻ࠊᳳ˄ࡴ⛁˅
˄ԡ˖⾦˅
⬉䕧ߎ˄⫼Ѣ偅ࡼSSR˅˖2
᡹䄺1㉏ൟ˖
ҙ䰤ᣛᅮൟো
᥻ࠊᳳ˄ދ˅
˄ԡ˖⾦˅
⬉䕧ߎ˄⫼Ѣ偅ࡼSSR˅˖2
ST˄㞾󰶖ℷ˅
ST ON = on
ST OFF = off
ℷ৥/ড৥䖤㸠
ড৥䖤㸠˄ࡴ⛁˅Ё= or-r
ℷ৥䖤㸠˄ދ˅Ё= or-d
3
4
6
6
6
6
6
6
6
6
6
in-t
5
in-h
100
in-l
0
dp
0
d-u
c
sl-h
1300
sl-l
-200
cntl
onof
s-hc
stnd
st
on
⿟ᑣ῵ᓣ
ptrn
off
cp
20
c-cp
20
orev
or-r
alt1
2
6
 tr-t
off
6tr-h
100.0
6tr-l
0.0
6ev-1
msp0
6ev-2
stop
6ev-3
none
6ev-4
none
6sqr
off
6amov
0
6
prlp
0
᡹䄺1⒲ৢ
alh1
0.2
᡹䄺2⒲ৢ
alh2
0.2
6alt3
2
᡹䄺2㉏ൟ˖
ҙ䰤ᣛᅮൟো
alt2
2
䇗ᭈ㦰
ҙ೼䖯ܹ䇗ᭈ㦰ᯊ
ᰒ⼎ϔ󱂖DŽ
6
8l.adj
at
off
6ct1
0.0
䗮ֵݭܹ
6cmwt
off
SP῵ᓣ
6spmd
lsp
6ࡴ⛁఼ᮁ㒓Ẕ⌟1
˄ԡ˖A˅7
hb1
0.0
6ct2
0.0
6ࡴ⛁఼ᮁ㒓Ẕ⌟2
˄ԡ˖A˅7
hb2
0.0
ֱ⏽ᯊ䯈
6soak
1
MVϞ䰤
6ol-h
100.0
᠟ࡼ໡ԡؐ
6of-r
50.0
ㄝᕙ䯈
6wt-b
off
ذℶᯊⱘMV
6mv-s
0.0
PVߎ䫭ᯊⱘMV
6mv-e
0.0
SP᭰വ䆒ᅮؐ
6sprt
off
SP᭰വ䆒ᅮؐ
˄SP᭰വϟ䰡ؐ˅
6sprl
same
⒲ৢ˄ދ˅
6chys
1.0
PV䕧ܹأ⿏䞣
6ins
0.0
6inrt
1.000
6rss
00
6rsrt
1.000
6lcr1
0.0
⿃ߚᯊ䯈
˄ԡ˖⾦˅
6i
233
ᖂߚᯊ䯈
˄ԡ˖⾦˅
6d
40 MVϟ䰤
6ol-l
0.0
6orl
0.0
6sqrp
0.0
6lcr2
0.0
HS᡹䄺1
˄ԡ˖A˅7
6hs1
50.0
HS᡹䄺2
˄ԡ˖A˅7
6hs2
50.0
SP 0
6sp-0
0
SP 1
6sp-1
0
SP 3
6sp-3
0
SP 4
6sp-4
0
SP 5
6sp-5
0
SP 6
6sp-6
0
SP 7
6sp-7
0
SP 2
6sp-2
0
25
0
䖛⿟ؐ/䆒ᅮؐ
䖲᥹ⱘӴᛳ఼Ϣ䕧ܹ
㉏ൟϡৠᯊˈᰒ⼎
s.errDŽ
ATᠻ㸠/প⍜
100%ATᠻ㸠at-2
40%ATᠻ㸠at-1
⅏
6c-db
0.0
⒲ৢ˄ࡴ⛁˅
6hys
1.0
6
᡹䄺3⒲ৢ
᡹䄺3㉏ൟ
alh3
0.2
6
᡹䄺4㉏ൟ
alt4
2
6
᥻ࠊ䕧ߎ1ֵো
o1st
4-20
6
Ӵ䗕䕧ߎֵো
trst
4-20
6᡹䄺4⒲ৢ
alh4
0.2
6p
8.0
⿃ߚᯊ䯈
˄ދ˅
˄ԡ˖⾦˅
6c-i
233
ᖂߚᯊ䯈
˄ދ˅
˄ԡ˖⾦˅
6c-d
40
↨՟ᏺ
˄ދ˅
6c-p
8.0
420mA
020mA
15V
05V
010V
25
26
27
28
29
䆒ᅮ㣗ೈ
䕧ܹ㉏ൟ 䕧ܹ
Pt100
JPt100
⛁⬉ي K
J
T
E
L
U
N
R
S
B
W
PL II
䆒ᅮ
1070°C
60120°C
115165°C
140260°C
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
17
18 12
15
16
1
2
13
14
3
11
4
6
7
8
9
10
5
ヺড়EN/IEC󰵼ޚ
Ꮉ԰ᣛ⼎
gSUB1˖䕙ࡽ䕧ߎ1ᣛ⼎
gSUB2˖䕙ࡽ䕧ߎ2ᣛ⼎
gSUB3˖䕙ࡽ䕧ߎ3ᣛ⼎
gOUT1˖᥻ࠊ䕧ߎ1ᣛ⼎
gOUT2˖᥻ࠊ䕧ߎ2ᣛ⼎
6
4
5
6
A
B
B5
6
Pt +

mA

+
5
4
2 Ӵᛳ఼⏽ᑺ/῵ᢳ䞣䕧ܹ
V
5
V6
+
4
TC
4
I
˄᮴ᵕᗻ˅
11
12
4 䕧ܹ⬉⑤
11
12
100240 VAC 24 VAC/DC
˄64˅
58
604
144.8u44.8 5. 䗝乍
1. ᥻ࠊ䕧ߎ
10
7
8
9
3 䕙ࡽ䕧ߎ
䕙ࡽ䕧ߎ1ǃ2䕙ࡽ䕧ߎ1ǃ2ǃ3
7
8
9
10
䕙ࡽ䕧ߎ1
䕙ࡽ䕧ߎ2
䕙ࡽ䕧ߎ2
䕙ࡽ䕧ߎ3
䕙ࡽ䕧ߎ1
18
++

+
+

13
16
17
16
17
18
13
16
17
18
13
14
15
13
14
15
18
16
18
13
14
15
16
17
18
16
17
005
џӊ䕧ܹ14
004
13
13
14
15
16
007
006
5 䗝乍
001
1717
18
V
I
V
mA
002 003
14
15
14
15
14
15
EV1
EV2
EV1
EV2
EV1
EV2
EV1
EV2
EV3
EV4
EV3
EV4
CT1 CT1
B˄+˅
A˄˅
RS-485
B˄+˅
A˄˅
RS-485
B˄+˅
A˄˅
RS-485
CT2
COM
CT1
+

3
1
2
3
1
2
1Ͼ㒻⬉఼
䕧ߎ
3+䕧ߎ2
Q
1+
2
3
2Ͼ⬉䕧ߎ
1 ᥻ࠊ䕧ߎ1ǃ2
䕧ߎ1
Q
1
2
1Ͼ⬉䕧ߎ
+
RX QX CX
䇋࣓ᢚϟ᥹㒓ᵓDŽ৺߭ˈӮᇐ㟈ᬙ䱰៪䇃ࡼ԰DŽ
ѻકⱘϞ䚼໛᳝䇗䆩Ꮉ݋ッষDŽᔧ䳔Փ⫼䇗䆩Ꮉ݋ᯊˈৃ䗮䖛䆹ッষᇚϾҎ䅵ㅫᴎϢᴀѻકⳌ䖲DŽ䖲᥹ϾҎ䅵ㅫᴎϢѻક䳔㽕
E58-CIFQ2 USBІ㸠䕀ᤶ⬉㓚DŽ˄Փ⫼䆹ѻકᯊϡৃϔⳈ䖲᥹USBІ㸠䕀ᤶ⬉㓚DŽ˅
䆺㒚ⱘ䖲᥹ᮍ⊩ˈ䇋খ✻USBІ㸠䕀ᤶ⬉㓚䰘ᏺⱘՓ⫼䇈ᯢкDŽ
g㄀ϔᰒ⼎
䖛⿟ؐ៪䆒ᅮ᭄᥂㉏ൟ
g㄀Ѡᰒ⼎
䆒ᅮؐǃ䆒ᅮ᭄᥂䇏ߎؐ៪᳈ᬍⱘ䕧ܹؐ
g৥Ϟ৥ϟ䬂
↣ᣝϔ󱂖U䬂ˈ㄀Ѡᰒ⼎Ϟⱘؐᇚ๲໻៪ᰒ
⼎ϟϔϾؐDŽ
↣ᣝϔ󱂖D䬂ˈ㄀Ѡᰒ⼎Ϟⱘؐᇚޣᇣ៪䖨
ಲϞϔϾؐDŽ
gRSP˖䖰⿟SPᣛ⼎
ᔧߚ䜡ࡳ㛑ЎONᯊ⚍҂DŽ
gTUNE˖
㞾󰶖ℷᯊ䮾⚕DŽ
㞾ᭈᅮᯊ⚍҂DŽ
gSTOP˖᥻ࠊذℶᣛ⼎
೼䖤㸠Ё“䖤㸠/ذℶ”ذℶᯊ⚍҂DŽ
೼᥻ࠊذℶᳳ䯈ˈ䰸᥻ࠊ䕧ߎП໪ⱘࡳ㛑ഛ
᳝ᬜDŽ
gCMW˖䗮ֵݭܕ䆌/⽕ℶᣛ⼎
ᔧ䗮ֵݭܕ䆌ᯊ⚍҂ˈ⽕ℶᯊ❘♁DŽ
E5CC
QQ
䕧ܹ㉏ൟ
-200850
-199.9500.0
0.0100.0
-199.9500.0
0.0100.0
-2001300
-20.0500.0
-100850
-20.0400.0
-200400
-199.9400.0
-200600
-100850
-200400
-199.9400.0
-2001300
01700
01700
1001800
02300
01300
090
0120
0165
0260
-3001500
-199.9900.0
0.0210.0
-199.9900.0
0.0210.0
-3002300
0.0900.0
-1001500
0.0750.0
-300700
-199.9700.0
-3001100
-1001500
-300700
-199.9700.0
-3002300
03000
03000
3003200
03200
02300
0190
0240
0320
0 500
䪖⬉䰏
⏽ᑺ䅵
咬䅸ؐᰃ“5”DŽ
ᔧ䕧ܹ㉏ൟϡᰃ䪖⬉䰏㗠䫭䇃ⱘᇚ䪖⬉䰏᥹ܹᯊˈᇚӮᰒ⼎s.errDŽЎњ⏙䰸s.err
ᰒ⼎ˈ䳔㽕ℷ⹂᥹㒓ᑊ䞡ᮄϞ⬉DŽ
°C= c
°F= f
3
4
߱ྟ䆒ᅮ㦰ৃҹՓ⫼᠋ᣛᅮ୰󱂗ⱘᎹ԰ᴵӊ˄䕧ܹ㉏ൟǃ᡹䄺㉏
ൟǃ᥻ࠊᮍ⊩ㄝㄝ˅DŽ
3: ݇Ѣ䕧ܹ㉏ൟ᡹䄺㉏ൟⱘ䆺㒚ᚙމˈ䇋খ㗗ᮕ䖍ⱘ㸼ḐDŽ
4: া䗖⫼Ѣ᳝᡹䄺ࡳ㛑ⱘൟোDŽ
5: ᔧ䕀㟇߱ྟ䆒ᅮ㦰ᯊ䖤㸠ذℶDŽ
˄᥻ࠊ/᡹䄺ഛذℶDŽ˅
6: ᇍѢᶤѯൟোҹঞ݊ᅗ䆒ᅮ乍ⱘᶤѯ䆒ᅮˈϡᰒ⼎♄㡆䆒ᅮ乍DŽ
7: া䗖⫼Ѣ᳝ࡴ⛁఼ᮁ㒓ࡳ㛑ⱘൟোDŽ
8: ㄀Ѡᰒ⼎Ёᰒ⼎ಯԡ᭄ⱘѻકҷⷕDŽ䆹䆒ᅮ᮴⊩ব᳈ˈ⫼᠋᮴䳔঺㸠䆒




᪡԰㦰
SP᭰വᳳ䯈ⱘ䆒ᅮؐ
6sp-m
0
ࡴ⛁఼⬉⌕1
ؐⲥ᥻
˄ԡ˖A˅
6ct1
0.0
ࡴ⛁఼⬉⌕2
ؐⲥ᥻
˄ԡ˖A˅
6ct2
0.0
໮SP
䆒ᅮؐ䗝ᢽ
6m-sp
0
䖰⿟SPⲥ᥻
6rsp
0.0
㞾ࡼ/᠟ࡼߛᤶ
ҙ䰤PID ᥻ࠊ
6a-m
ⓣ⬉⌕1
ؐⲥ᥻
˄ԡ˖A˅
6lcr1
0.0
ⓣ⬉⌕2
ؐⲥ᥻
˄ԡ˖A˅7
6lcr2
0.0
⿟ᑣࡼ
6prst
rset
࠽ԭֱ⏽ᯊ䯈
6sktr
0
RUN/STOP
6r-s
run
᡹䄺ؐ1 4
6al-1
0
᡹䄺ؐϞ䰤1
4
6al1h
0
ᔧ᥻ࠊࡼ=runᯊ
ᔧ᥻ࠊذℶ=stopᯊ
᪡԰ᯊᑨℷᐌՓ⫼᪡԰㦰DŽ
ֱᡸ㦰
䰤ࠊৃҹᰒ⼎៪ᬍবⱘ䆒ᅮ㉏ൟҹঞ䗮䖛ᣝ䬂᪡԰䖯㸠ⱘ᳈ᬍDŽ
䖭ᰃϔ⾡A㉏ѻકDŽ
಴݊೼ԣᅙЁӮᇐ㟈᮴㒓⬉ᑆᡄˈ᠔ҹ㽕∖⫼᠋䞛প䗖ᔧⱘ᥾ᮑޣᇥᑆᡄDŽ
䇗ᭈ㦰
া᳝Āinsᯊ˖⏽ᑺ䕧ܹأ⿏āখ᭄Ёⱘ䆒ᅮؐᑨ⫼ѢᭈϾ⏽ᑺ䕧ܹ㣗ೈDŽབᵰ䕧ܹأ⿏ؐ䆒ᅮЎ1.2°Cˈ
߭䖛⿟ؐЎ200°Cᯊˈ㒣䖛䕧ܹأ⿏ৢᣝ✻201.2°C໘⧚DŽ㗠བᵰ䕧ܹأ⿏ؐ䆒ᅮЎ-1.2°Cˈ߭㒣䖛䕧ܹأ
⿏ৢ䖛⿟ؐᣝ✻198.8°C໘⧚DŽ
䇗ᭈ㦰⫼Ѣ೼᥻ࠊᯊ䕧ܹ䆒ᅮؐأ⿏ؐDŽ
1654640-7E
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Ўヺড়EMC󰵼ޚˈ䖲᥹Ӵᛳ఼ⱘ⬉㓚ϡᕫ䭓Ѣ30㉇DŽ
བᵰ⬉㓚䭓ᑺ䍙䖛30㉇ˈ߭ϡヺড়EMC󰵼ޚDŽ
⣀ᅝ㺙˄mm˅ ᑊᥦᅝ㺙˄mm˅
gᇚЏܗᦦܹ䴶ᵓ˄15mm˅ⱘᅝ㺙ᄨЁDŽᡞᅝ㺙ᬃᶊ˄ᦤկ˅ᦦܹৢ໇乊䚼ᑩ䚼ⱘ
೎ᅮῑЁDŽ
gᢻ㋻䗖䜡఼乊䚼ᑩ䚼ⱘϸ乫ᅝ㺙㶎ϱՓֱ݊ᣕᑇ㸵ˈ᳔㒜Փ݊ᡁⶽֱᣕ೼0.29㟇
0.39NgmП䯈DŽ
gᔧᅝ㺙໮ৄᴎ఼ᯊˈ䇋⹂ֱ⦃๗⏽ᑺϡ䍙䖛㾘ᅮ䰤ؐDŽ
ᑊᥦᅝ㺙᮴⊩⹂ֱ䰆∈ᗻ㛑DŽ
ᔧ᳝䰆∈㽕∖ᯊˈ䇋೼ࠡ䴶
ᵓⱘৢջᅝ㺙䰆∈ᆚᇕ೜DŽ
°C °F
⏙䰸P៪PD᥻ࠊᳳ䯈
ⱘأ⿏䞣
ᑇᮍḍⱘᦤপ
Low-cut⚍
6plcm
1234
䗮ֵⲥ᥻
MVব࣪
⥛ᵕ䰤
E5CC咬䅸䆒ᅮЎϔKൟ⛁⬉ي˄䕧ܹ㉏ൟ5˅DŽ
བᵰՓ⫼ϡৠⱘӴᛳ఼ˈ߭Ӯথ⫳䕧ܹ䫭䇃˄s.err˅DŽ
Ẕᶹ䕧ܹ㉏ൟখ᭄ⱘ䆒㕂DŽ
1Ͼ㒓ᗻ⬉⌕
䕧ߎ
џӊ䕧ܹ1ǃ2
CT1
䗮ֵ˄RS-485˅
CT1
䗮ֵ˄RS-485˅ǃ
CT1CT2
䗮ֵ˄RS-485˅
џӊ䕧ܹ3ǃ4
џӊ䕧ܹ1ǃ2䕀ᤶ
䕧ߎ
џӊ䕧ܹ1ǃ2䖰⿟
SP
㑶໪⏽ᑺӴᛳ
఼ES1B
↨՟㓽ᬒϟ䰤˄ҙ䰤
䆒ᅮ῵ᢳ䞣䕧ܹᯊ˅
ᇣ᭄⚍˄ҙ䰤䆒ᅮ
῵ᢳ䞣䕧ܹᯊ˅
↨՟㓽ᬒϞ䰤˄ҙ䰤
䆒ᅮ῵ᢳ䞣䕧ܹᯊ˅
⏽ᑺԡ
ᑇᮍḍⱘᦤপ
⫼
˄ҙ䰤Ꮖ䆒ᅮ῵
ᢳ䞣䕧ܹᯊ˅
䕀㟇催㑻ࡳ㛑䆒
ᅮ㦰
џӊ䕧ܹߚ䜡4
џӊ䕧ܹߚ䜡3
џӊ䕧ܹߚ䜡2
џӊ䕧ܹߚ䜡1
Ӵ䗕䕧ߎϟ䰤
Ӵ䗕䕧ߎϞ䰤
Ӵ䗕䕧ߎ㉏ൟ
˄㄀ϔᰒ⼎䮾⚕ˈ✊ৢ
᥻ࠊذℶDŽ˅
ᣝԣO
㟇ᇥ3⾦
ᣝԣO
㟇ᇥ1⾦
ᣝO
˄ϡ䍙䖛1⾦˅
ࡴ⛁఼⬉⌕1ؐⲥ᥻
˄ԡ˖A˅7
ࡴ⛁఼⬉⌕2ؐⲥ᥻
˄ԡ˖A˅7
ⓣ⬉⌕1ؐⲥ᥻
˄ԡ˖A˅7
ⓣ⬉⌕2ؐⲥ᥻
˄ԡ˖A˅7
PV䕧ܹ᭰വ㋏᭄
䖰⿟SP䕧ܹأ⿏
䖰⿟SP䕧ܹ᭰വ
㋏᭄
↨՟ᏺ
أᏂϞ/ϟ䰤ᕙᴎᑣ߫ON
أᏂϞ䰤ᕙᴎᑣ߫ON
أᏂϟ䰤ᕙᴎᑣ߫ON
㒱ᇍؐϞ䰤ᕙᴎᑣ߫ON
㒱ᇍؐϟ䰤ᕙᴎᑣ߫ON
ᣝԣOM䬂㟇ᇥ1⾦ᣝԣOM䬂㟇ᇥ3⾦
䕀㟇ֱᡸ㦰
ҙ೼䆒ᅮᆚⷕᯊᰒ⼎DŽ
䰤ࠊ䕀㟇ֱᡸ㦰DŽ
᪡԰/䇗ᭈֱᡸ
䰤ࠊ೼᪡԰㦰ǃ䇗ᭈ㦰
᠟ࡼ᥻ࠊ㦰Ёᰒ⼎
ׂᬍ㦰乍DŽ
߱ྟ䆒ᅮ/䗮ֱֵᡸ
䰤ࠊߛᤶ㟇߱ྟ䆒ᅮ㦰ǃ
䗮ֵ䆒ᅮ㦰催㑻ࡳ㛑
䆒ᅮ㦰DŽ
䆒ᅮব᳈ֱᡸ
䰤ࠊ䗮䖛᪡԰ࠡ䴶ᵓᣝ䬂
ᴹᬍব䆒ᅮDŽ
ҙ䰤Ꮖ᳈ᬍⱘখ
᭄
ܕ䆌খ᭄ሣ㬑
ҙ೼䆒ᅮখ᭄ሣ
㬑ᯊᰒ⼎DŽ
䕀㟇ֱᡸ㦰ⱘ
ᆚⷕ
⏽ᑺ䕧ܹ
䕧ߎ 1
R
䕧ߎ1
Q
䕧ߎ 1
C
೼ࣙ㺙ݙ᳝˖
gЏܗ
gՓ⫼䇈ᯢк
g䰆∈ᆚᇕ೜˄Y92S-P8˅˖c
g䗖䜡఼˄Y92F-49˅˖d
gッᄤⲪ
˄ҙᏺ᳝E5CCƶƶƶƶ5ƶ
ⱘൟো䰘˅˖e
঺ଂӊ
gッᄤⲪ˄ൟো˖E53-COV23˅
gUSBІ㸠䕀ᤶ⬉㓚
˄E58-CIFQ2˅
48u48
䴲⛞᥹ッᄤሎᇌ˖M3 ⬉䕧ߎ˄⫼Ѣ偅ࡼSSR˅
12 VDCˈ21 mA
㒻⬉఼䕧ߎ
250 VACˈ3 A˄䰏ᗻ䋳䕑˅
⬉䕧ߎ˄⫼Ѣ偅ࡼSSR˅
12 VDCˈ21 mA
⬉⌕䕧ߎ
020 mA DC
䋳䕑˖᳔໻500 :
420 mA DC
㒻⬉఼䕧ߎ
2Ͼ䕧ߎ˖250 VACˈ3 A
˄䰏ᗻ䋳䕑˅
3Ͼ䕧ߎ˖250 VACˈ2 A
˄䰏ᗻ䋳䕑˅
᥻ࠊ䕧ߎ2
᥻ࠊ䕧ߎ1䕙ࡽ䕧ߎ1ǃ2ǃ3
3+
1+
2-
㒓ᗻ⬉⌕䕧ߎ/⬉䕧ߎൟ
䕧ߎ1
C
䕧ߎ2
Q
CQ
ce
d
LH
ON
OFF
SP
ヺড়ᅝܼ󰵼ޚ
೼䕧ܹ⬉⑤ǃ㒻⬉఼䕧ߎП䯈ҹঞ݊ᅗッᄤП䯈ᦤկњᔎ࣪㒱㓬DŽ
ࡵᖙՓᕫ⬉⑤ϔ󱂖ջϞথ⫳ⱘⶀ䯈䖛⬉ϡ㽕䍙䖛ҹϟ⬉ؐDŽ
䖬䇋ᣝ✻ᴀѻકⱘ⬉⑤⬉䖯㸠⹂䅸DŽ
ⷁᯊ䯈䖛⬉˖9˄⬉⑤⬉˅
䭓ᯊ䯈䖛⬉˖9˄⬉⑤⬉˅
೼Փ⫼ᴀѻકᯊˈ䇋ࡵᖙ໪᥹䇈ᯢкϞ᥼㤤ⱘֱ䰽ϱDŽ
݇Ѣ῵ᢳ䕧ܹ
g䕧ܹ⬉៪⬉⌕ᯊˈ䇋ᣝ✻ᴀѻકⱘ䕧ܹ㉏߿䆒ᅮ䕧ܹ㉏ൟDŽ
g䇋࣓ᇚᴀѻક⫼ᴹ⌟ᅮĀ⌟䞣㣗⭈Ў,,ǃ,,,ǃ,9āⱘಲ䏃DŽ
g䇋࣓ᇚᴀѻક⫼ᴹ⌟ᅮĀࡴ⬉䍙䖛9UPV៪9'&āⱘᇍ䈵DŽ
བᵰѻક᳾ᣝᴀ݀ৌᣛᅮⱘᮍ⊩Փ⫼ˈ䙷Мѻક݋໛ⱘֱᡸࡳ㛑ᕜৃ㛑
ᤳണDŽ

60 min.
45
45
+0.6
0
+0.6
0
+0.6
0
(48 x number of units - 2.5)+1
0
45
Indicates a potentially hazardous situation which, if
not avoided, is likely to result in minor or moderate
injury or property damage. Read this manual
carefully before using the product.
E5CC
Digital Controller
Be sure to observe the following precautions to prevent operation failure, malfunction, or adverse affects on the
performance and functions of the product. Not doing so may occasionally result in unexpected events.
Use the product within specifications.
(1) The product is designed for indoor use only. Do not use the product outdoors. Do not use or store the product
in any of the following locations.
Places directly subject to heat radiated from heating equipment.
Places subject to splashing liquid or oil atmosphere.
Places subject to direct sunlight.
Places subject to dust or corrosive gas (in particular, sulfide gas and ammonia gas).
Places subject to intense temperature change.
Places subject to icing and condensation.
Places subject to vibration and large shocks.
(2) Use/store within the rated temperature and humidity ranges. Provide forced-cooling if required.
(3) To allow heat to escape, do not block the area around the product.
Do not block the ventilation holes on the product.
(4) Be sure to wire properly with correct polarity of terminals.
(5) Use the specified size of crimped terminals (M3, width 5.8 mm or less) for wiring. To connect bare wires to the
terminal block, use copper braided or solid wires with a gage of AWG24 to AWG18 (equal to cross- sectional
area of 0.205 to 0.8231 mm
2
). (The stripping length is 6 to 8 mm.) Up to two wires of same size and type, or
two crimped terminals can be inserted into a single terminal.
(6) Do not wire the terminals which are not used.
(7) Allow as much space as possible between the controller and devices that generate a powerful high- frequency
or surge. Separate the high-voltage or large-current power lines from other lines, and avoid parallel or
common wiring with the power lines when you are wiring to the terminals.
(8) Use this product within the rated load and power supply.
(9) Make sure that the rated voltage is attained within two seconds of turning ON the power using a switch or relay
contact. If the voltage is applied gradually, the power may not be reset or output malfunctions may occur.
(10) Make sure that the Digital Controller has 30 minutes or more to warm up after turning ON the power before
starting actual control operations to ensure the correct temperature display.
(11) When executing self-tuning, turn the load and the unit ON simultaneously, or turn the load ON before you turn
the controller ON.
(12) A switch or circuit breaker should be provided close to this unit. The switch or circuit breaker should be within
easy reach of the operator, and must be marked as a disconnecting means for this unit.
(13) Wipe off any dirt from the Digital Controller with a soft dry cloth. Never use thinners, benzine, alcohol, or any
cleaners that contain these or other organic solvents. Deformation or discoloration may occur.
(14) Design system (control panel, etc) considering the 2 second of delay that the controller’s output to be set after
power ON.
(15) The output will turn OFF when you move to the Initial Setting Level. Take this into consideration when
performing control.
(16) The number of non-volatile memory write operations is limited. Therefore, use RAM write mode when
frequently overwriting data during communications or other operations.
(17) When disassembling the Temperature Controller for disposal, use suitable tools.
(18) Do not exceed the communications distance that is given in the specifications and use the specified
communications cable. Refer to the E5□C Digital Controllers User’s Manual (Cat. No.H174) for the
communications distance and cable specifications.
(19) Do not turn the power supply to the Digital Controller ON or OFF while the USB-Serial Conversion Cable is
connected. The Digital Controller may malfunction.
(20) The maximum terminal temperature is 75°C.
Precautions for Safe Use
Refer to the E5□C Digital Controllers User’s Manual (Cat. No. H174)
for detailed application procedures.
INSTRUCTION MANUAL
Thank you for purchasing the OMRON E5CC Digital Controller.
This manual describes the functions, performance, and
application methods needed for optimum use of the product.
Please observe the following items when using the product.
This product is designed for use by qualified personnel with
a knowledge of electrical systems.
 Before using the product, thoroughly read and understand
this manual to ensure correct use.
 Keep this manual in a safe location so that it is available for
reference whenever required.
OMRON Corporation
©All Rights Reserved
Refer to the E5□C Digital Controllers User’s Manual (Cat. No.
H174) for information on the Advanced Function Setting Level,
Manual Control Level, and other functions.
Refer to the E5□C Digital Controllers Communications Manual (Cat.
No. H175) for information on communications.
Power supply voltage 100 to 240 VAC, 50/60 Hz or
24 VAC, 50/60 Hz / 24 VDC
Operating voltage range 85 to 110% of the rated voltage
Power consumption
Option 000: 5.2 VA max. (100 to 240 VAC)
3.1 VA max. (24 VAC)/1.6 W max. (24 VDC)
All other specifications: 6.5 VA max. (100 to 240 VAC)
4.1 VA max. (24 VAC)/2.3 W max. (24 VDC)
Indication accuracy Thermocouple:
(Ambient temperature: 23°C) (±0.3 % of indication value or ±1°C,
whichever is greater) ±1 digit max.
Platinum resistance thermometer:
(±0.2 % of indication value or ±0.8°C,
whichever is greater) ±1 digit max.
Analog input:
±0.2 % FS ±1 digit max.
Event input Output current: approx. 7 mA per contact.
Contact input ON:1 kk
No-contact input ON: residual voltage 1.5 V max.,
OFF: leakage current 0.1 mA max.
Remote SP input 4 to 20 mA DC or 0 to 20 mA DC
0 to 5 V DC or 1 to 5 V DC or 0 to 10 V DC
Control output 1 Relay output :SPST-NO
250VAC, 3A(resistive load)
Electrical life of relay: 100,000 operations
Voltage output (for driving SSR):
12 VDC ±20%, 21 mA
Current output: 4 to 20 mA DC, 0 to 20mA DC
Load: 500 
Control output 2 Voltage output (for driving SSR):
12 VDC, 21 mA
Control method ON/OFF or 2-PID control
Auxiliary outputs Relay outputs:SPST-NO, 250 VAC,
two outputs: 3 A (resistive load),
three outputs: 2 A (resistive load),
Electrical life of relay: 100,000 operations
 
 
Ambient temperature -10 to 55°C
(Avoid freezing or condensation)
Ambient humidity 25% to 85%
Storage temperature -25 to 65°C
(Avoid freezing or condensation)
Altitude Max. 2,000m
Recommended fuse
T2A, 250 VAC, time-lag, low-breaking capacity
Weight Approx. 120 g (Digital Controller only)
Degree of protection Front panel: IP66
Rear case: IP20, Terminal section: IP00
Installation environment Installation category II, pollution
degree 2 (as per IEC61010-1)
Memory protection Non-volatile memory
(Number of write operations: 1,000,000)
Temporary overvoltage Short term: 1200 V+ (power supply voltage)
Long term: 250 V+ (power supply voltage)
CAUTION
CAUTION
Minor injury due to electric shock may occasionally occur.
Do not touch the terminals while power is being supplied.
Electric shock, fire, or malfunction may occasionally occur. Do not allow metal objects, conductors,
cuttings from installation work, or moisture to enter the Digital Controller, the Setup Tool ports, or
between the pins on the connectors on the Setup Tool cable.
Do not use the product where subject to flammable or explosive gas. Otherwise, minor injury from
explosion may occasionally occur.
Never disassemble, modify, or repair the product or touch any of the internal parts. Minor electric
shock, fire, or malfunction may occasionally occur.
CAUTION - Risk of Fire and Electric Shock
a) This is the product UL listed as Open Type Process Control Equipment. It must be mounted in an enclosure
that does not allow fire to escape externally.
b) More than one disconnect switch may be required to de-energize the equipment before servicing.
c) Signal inputs are SELV, limited energy.
d) Caution: To reduce the risk of fire or electric shock, do not interconnect the outputs of different Class 2 circuits.
If the output relays are used past their life expectancy, contact fusing or burning may occasionally occur.
Always consider the application conditions and use the output relays within their rated load and
electrical life expectancy. The life expectancy of output relays varies considerably with the output load
and switching conditions.
Loose screws may occasionally result in fire. Tighten the terminal screws to the specified torque of 0.43

Set the parameters of the product so that they are suitable for the system being controlled. If they are
not suitable, unexpected operation may occasionally result in property damage or accidents.
A malfunction in the Digital Controller may occasionally make control operations impossible or prevent
alarm outputs, resulting in property damage. To maintain safety in the event of malfunction of the Digital
Controller, take appropriate safety measures, such as installing a monitoring device on a separate line.
EN
Safety Precautions
Key to Warning Symbols
Dimensions
*2: Error shown only for "Process value / Set point". Not shown for other status.
When an error has occurred, the No.1 display shows the error code. Take necessary measure
according to the error code, referring the table below.
If the input value exceeds the display limit (-1999 to 9999), though it is within the control
range, [[[[ will be displayed under -1999 and ]]]] above 9999. Under these conditions,
control output and alarm output will operate normally.
Refer to the E5□C Digital Controllers User’s Manual (Cat. No. H174) for the controllable ranges.
Check the setting of the Input Type parameter,
check the input wiring, and check for broken or
shorts in the temperature sensor.
Turn the power OFF then back ON again. If the
display remains the same, the controller must be
repaired. If the display is restored to normal, then
a probable cause can be external noise affecting
the control system. Check for external noise.
After the correction of A/Dconverter error, turn the
power OFF then back ON again. If the display
remains the same, the controller must be repaired.
If the display is restored to normal, then a
probable cause can be external noise affecting the
control system. Check for external noise.
No.1 display Meaning
A/D converter error
*2
Memory error
Input error
*2
s.err (S. Err)
e111 (E 111)
Action
OFF
Alarm
Control
output
Status at error
OFF
OFF
Operates
as above the
upper limit.
OFF
OFF
e333 (E333)
Error Display (troubleshooting)
Warning Symbols
Installation Connections (The applicability of the electric terminals varies with the type of machine.)
Specifications
Other functions
Wiring
Names of Parts on Front Panel
 °C / °F : temperature unit
The temperature unit is displayed when the displayed value
is a temperature. Either Cor Fis displayed according to
the set value of the temperature unit.
 Mode key
Press this key to change the contents of the display.
Press this button for 1 s or longer for reverse scroll.
 Press the Okey and the Mkey together for at
least 3 seconds to switch to protect level.
 Level key
Use this key to change levels:
 Shift key (PF key)
The default PF Setting parameter is for shifting the digit.
This is a function key. When it is pressed, the function
set for the PF Setting parameter will operate.
 :Protection indicator
Lit when Setting Change Protect is
ON (disables the Up and Down Keys).
MANU: Manual output indicator
Lit when the Auto/Manual Mode is set
to Manual Mode.
Operation Menu
*1: Upper and lower limits can be set for parameters 1, 4 and 5 to
provide for different types of alarm. These are indicated by the
letter "L" and "H".

Alarms
OMRON EUROPE B.V.
Wegalaan 67-69, NL-2132 JD Hoofddorp The Netherlands
Phone [phone]
FAX [phone]
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg, IL 60173-5302 U.S.A
Phone [phone]
FAX [phone]
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark, Singapore 119967
Phone [phone]
FAX [phone]
OMRON Corporation
Shiokoji Horikawa, Shimogyo-ku, Kyoto 600-8530 JAPAN
Suitability for Use
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which
apply to the combination of the Product in the Buyer’s application or use of the Product.
At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not sufficient for a complete
determination of the suitability of the Product in combination with the end product, machine, system, or
other application or use. Buyer shall be solely responsible for determining appropriateness of the particular
product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in
all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED
FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Conformance to Safety Standard
Reinforced insulation is provided between input power
supply, relay outputs, and between other terminals.
Do not allow temporary overvoltages on the primary circuit to exceed
the following values.
Check the power supply voltage to the Digital Controller.
Short-term overvoltage: 1,200 V + (Power supply voltage)
Long-term overvoltage: 250 V + (Power supply voltage)
Always externally connect the recommended fuse that is specified
in the Instruction Manual before you use the Digital Controller.
Analog Input

If you input an analog voltage or current, set the Input Type
parameter to the correct input type.
 Do not use the Digital Controller to measure a circuit with
Measurement Category II, III, or IV.

Do not use the Digital Controller to measure an energized circuit to
which a voltage that exceeds 30 Vms or 60 VDC is applied.
The protection provided by the Digital Controller may be impaired if the
Digital Controller is used in a manner that is not specified by the
manufacturer.
Operation stopped.
(Control/alarm are both stopped.)
*5
Initial Setting Level
Use the following ranges for scaling: -1999
to 9999, -199.9 to 999.9, -19.99 to 99.99,
-1.999 to 9.999
Analog
input type
Current input
Voltage input
Do not connect anything to the terminals that are shaded gray.
Dimensions (mm)
The E5CC is set for a K thermocouple (input type of 5)
by default. If a different sensor is used, an input error
(s.err) will occur.
Check the setting of the Input Type parameter.
Check the wiring before turning ON the power supply.
*1
*1
*1
Alarm type
Vary with
"L", "H" values
Vary with
"L", "H" values
Vary with
"L", "H" values
No alarm function Output off
Deviation upper/lower limit
standby sequence ON
Absolute value upper limit
Absolute value lower limit
Absolute value upper limit
standby sequence ON
Absolute value lower limit
standby sequence ON
LBA (only for alarm 1)
Deviation lower limit
standby sequence ON
Deviation upper limit
standby sequence ON
Deviation upper/lower range
Deviation upper limit
Deviation upper/lower limit
Deviation lower limit
Alarm output function
Positive alarm value (X) Negative alarm value (X)
Setting
PV Change Rate Alarm
X
ON
OFF SP
X
ON
OFF SP
ON
OFF SP
X
X
ON
OFF SP
LH
ON
OFF SP
X
ON
OFF SP
X
ON
OFF SP
X
ON
OFF 0
ON
OFF
X
0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF
X
0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
X
ON
OFF 0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
ON
OFF
X
0
LH
ON
OFF SP
SP
ON
OFF
X
ON
OFF
X
0
1
0
2
3
4
5
6
7
8
9
SP absolute value upper limit
SP absolute value lower limit
14
15
MV absolute value upper limit
MV absolute value lower limit
16
17
RSP absolute value upper limit
RSP absolute value lower limit
18
19
10
11
12
13
SP
X
ON
OFF
ON
OFF
X
0
Operation / Adjustment Protect
Restricts displaying and
modifying menu items in
Operation, Adjustment,
and Manual Control Levels.
oapt
0
Move to Protect Level
Displayed only when a
password is set. Restricts
moving to Protect Level.
pmov
0
Changed
Parameters Only
chgp
off
Parameter Mask
Enable
Displayed only
when a parameter
mask is set.
pmsk
on
Initial Setting / Communication Protect
Restricts movement to the
Initial Setting, Communications
Setting, and Advanced Function
Setting Levels.
icpt
1
Setting Change Protect
Restricts changes to settings
by operating the front panel keys.
wtpt
off
pfpt
off
PF Key Protect
Restricts PF key operation.
POWER ON
MV Monitor
(Heating)
*6 o
0.0
MV Monitor
(Cooling)
*6 c-o
0.0
Alarm Value
Lower Limit 1 *4
*6 al1l
0
Alarm Value 2 *4
*6 al-2
0
Alarm Value
Upper Limit 2 *4
*6 al2h
0
Alarm Value
Lower Limit 2 *4
*6 al2l
0
Alarm Value 3 *4
*6 al-3
0
Alarm Value
Upper Limit 3 *4
*6 al3h
0
Alarm Value
Lower Limit 3 *4
*6 al3l
0
Alarm Value
Lower Limit 4 *4
*6 al4l
0
Alarm Value 4 *4
*6 al-4
0
Alarm Value
Upper Limit 4 *4
*6 al4h
0
Input Type *3
Scaling Upper Limit
(only when setting
analog input)
Scaling Lower Limit
(only when setting
analog input)
Decimal Point
(only when setting
analog input)
Temperature
Unit
SP Upper Limit
SP Lower Limit

In ON/OFF control = onof
In 2-PID control = pid
Standard or Heating/Cooling
Standard control =
stnd
Heating and cooling control =
h-c
Control Period (Heating)
(Unit: Seconds)
*Voltage output (for driving SSR): 2
Alarm 1 Type:
Specified models only
Control Period (Cooling)
(Unit: Seconds)
*Voltage output (for driving SSR): 2
ST (Self-Tuning)
ST ON = on
ST OFF = off
Direct/Reverse Operation
In Reverse operation (Heating) =
or-r
In Direct operation (Cooling) =
or-d
*3
*4
*6
*6
*6
*6
*6
*6
*6
*6
*6
in-t
5
in-h
100
in-l
0
dp
0
d-u
c
sl-h
1300
sl-l
-200
cntl
onof
s-hc
stnd
st
on
Program Pattern
ptrn
off
cp
20
c-cp
20
orev
or-r
alt1
2
*6
Transfer
Output Type
*6 tr-t
off
Transfer Output
Upper Limit
*6 tr-h
100.0
Transfer Output
Lower Limit
*6 tr-l
0.0
Event Input
Assignment 1
*6 ev-1
msp0
Event Input
Assignment 2
*6 ev-2
stop
Event Input
Assignment 3
*6 ev-3
none
Event Input
Assignment 4
*6 ev-4
none
Extraction of Square
Root Enable
(Only when analog
input is set)
*6 sqr
off
Move to Advanced
Function Setting
Level
*6 amov
0
*6
Password to Move
to Protect Level
prlp
0
Alarm 1 Hysteresis
alh1
0.2
Alarm 2 Hysteresis
alh2
0.2
*6 Alarm 3
Type
alt3
2
Alarm 2 Type:
Specified models only
alt2
2
Adjustment Level
Displayed only once when
entering Adjustment Level.
*6
*8 l.adj
at
off
Heater Current 1 Value
Monitor (Unit: A) *7
*6 ct1
0.0
Communications Writing
*6 cmwt
off
SP Mode
*6 spmd
lsp
*6
Heater Burnout Detection 1
(Unit: A) *7
hb1
0.0
Heater Current 2 Value
Monitor (Unit: A) *7
*6 ct2
0.0
*6
Heater Burnout Detection 2
(Unit: A) *7
hb2
0.0
Soak Time
*6 soak
1
MV Upper Limit
*6 ol-h
100.0
Manual Reset Value
Clears the offset
during P or PD control.
*6 of-r
50.0
Wait Band
*6 wt-b
off
MV at Stop
*6 mv-s
0.0
MV at PV Error
*6 mv-e
0.0
SP Ramp Set Value
*6 sprt
off
SP Ramp Set Value
(SP Ramp Fall Value)
*6 sprl
same
Hysteresis (Cooling)
*6 chys
1.0
PV
Input Shift
*6 ins
0.0
PV input
Slope Coefficient
*6 inrt
1.000
Remote SP
Input Shift
*6 rss
0.0
Remote SP input
Slope Coefficient
*6 rsrt
1.000
Leakage Current 1 Value
Monitor (Unit: A) *7
*6 lcr1
0.0
Integral Time
(Unit: Seconds)
*6 i
233
Derivative Time
(Unit: Seconds)
*6 d
40 MV Lower Limit
*6 ol-l
0.0
MV Change
Rate Limit
*6 orl
0.0
Extraction of Square
Root Low-cut Point
*6 sqrp
0.0
Leakage Current 2 Value
Monitor (Unit: A) *7
*6 lcr2
0.0
HS Alarm 1
(Unit: A) *7
*6 hs1
50.0
HS Alarm 2
(Unit: A) *7
*6 hs2
50.0
SP 0
*6 sp-0
0
SP 1
*6 sp-1
0
SP 3
*6 sp-3
0
SP 4
*6 sp-4
0
SP 5
*6 sp-5
0
SP 6
*6 sp-6
0
SP 7
*6 sp-7
0
SP 2
*6 sp-2
0
25
0
Process Value/Set Point
s.err is displayed when
connected sensor is
different from input type.
AT Execute / Cancel
100%AT Execute at-2
40%AT Execute at-1
Dead Band
*6 c-db
0.0
Hysteresis (Heating)
*6 hys
1.0
*6
Alarm 3
Hysteresis
alh3
0.2
*6 Alarm 4
Type
alt4
2
*6
Control Output 1
Signal
o1st
4-20
*6 Transfer
Output Signal
trst
4-20
*6
Alarm 4
Hysteresis
alh4
0.2
Proportional
Band
*6 p
8.0
Integral Time
(Cooling)
(Unit: Seconds)
*6 c-i
233
Derivative Time
(Cooling)
(Unit: Seconds)
*6 c-d
40
Proportional Band
(Cooling)
*6 c-p
8.0
4 to 20mA
0 to 20mA
1 to 5V
0 to 5V
0 to 10V
25
26
27
28
29
Setting range
Input type Input
Pt100
JPt100
Thermocouple
Infrared
Thermosensor
ES1B
K
J
T
E
L
U
N
R
S
B
W
PL II
Setting
10 to 70°C
60 to 120°C
115 to 165°C
140 to 260°C
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
17
18 12
15
16
1
2
13
14
3
11
4
6
7
8
9
10
5
Operation indicators
 SUB1: Auxiliary output 1 indicator
 SUB2: Auxiliary output 2 indicator
SUB3: Auxiliary output 3 indicator
 OUT1: Control output 1 indicator
OUT2: Control output 2 indicator
6
4
5
6
5
6
Pt
+

mA

+
5
4
*2 Sensor Temperature/Analog Input
V
5
V6
+
4
TC
4
I
(no polarity)
11
12
*4 Input Power Supply
11
12
100 to 240 VAC 24 VAC/DC
(64)
85
604
144.8u44.8 5. Options
1. Control outputs
10
7
8
9
*3 Auxiliary Outputs
Auxiliary outputs 1 and 2 Auxiliary outputs 1, 2, and 3
7
8
9
10
Auxiliary output 1
Auxiliary output 2
Auxiliary output 2
Auxiliary output 3
Auxiliary output 1
18
++

+
+

13
16
17
16
17
18
13
16
17
18
13
14
15
13
14
15
18
16
18
13
14
15
16
17
18
16
17
005
Event inputs 1 to 4
004
Communications (RS-485)
and event inputs 3 and 4
13
13
14
15
16
007
Event inputs 1 and 2,
and remote SP
006
Event inputs 1 and 2, and
transfer output
*5 Options
001
Event inputs 1 and 2,
and CT1
1717
18
V
I
V
mA
002
Communications
(RS-485) and CT1
003
Communications
(RS-485), CT1, and CT2
14
15
14
15
14
15
EV1
EV2
EV1
EV2
EV1
EV2
EV1
EV2
EV3
EV4
EV3
EV4
CT1 CT1
B(+)
A()
RS-485
B(+)
A()
RS-485
B(+)
A()
RS-485
CT2
COM
CT1
+

3
1
2
3
1
2
One linear
current output
One relay
output
3+Q
1+
2
3
Two voltage outputs
(for driving SSR)
*1 Control Outputs 1 and 2
Q
1
2
One voltage output
(for driving SSR)
+
RX QX CX
Sold Separately
*Terminal cover (E53-COV23)
*USB-Serial Conversion Cable
(E58-CIFQ2)
In the pack:
*Main unit
*Instruction manual
*Watertight packing (Y92S-P8): c
*Adapter (Y92F-49): d
* Terminal cover (Provided only for
models with E5CC-ƶƶƶƶ5ƶ):
e
* Do not remove the terminal block. Doing so may result in failure or malfunction.
* A Setup Tool port is provided on the upper of the product. Use this port to connect a personal computer to the product when using
the Setup Tool. E58-CIFQ2 USB-Serial Conversion Cable is required to connect the personal computer to the product. (Do not use
the product with the USB-Serial Conversion Cable left permanently connected.)
Refer to the instruction manual provided with the USB-Serial Conversion Cable for details on connection methods.
No.1 display
Process value or set data type
No.2 display
Set point, set data read-out value or changed input
value
Up and Down keys
Each press of Ukey increments or advances the
values displayed on the No.2 display.
Each press of Dkey decrements or returns the
values displayed on the No.2 display.
RSP: Remote SP indicator
Lit when the assigned function is ON.
TUNE:
Flashing during self-tuning.
Lit during auto-tuning.
STOP: Control stopped indicator
Lit when “Run/Stop” is stopped during operation.
During control stop, functions other than control output
are valid.
CMW: Communications writing
enabled/disabled indicator
Lit when communications writing is enabled and not lit
when it is disabled.
E5CC
QQ
Input Type
-200 to 850
-199.9 to 500.0
0.0 to 100.0
-199.9 to 500.0
0.0 to 100.0
-200 to 1300
-20.0 to 500.0
-100 to 850
-20.0 to 400.0
-200 to 400
-199.9 to 400.0
-200 to 600
-100 to 850
-200 to 400
-199.9 to 400.0
-200 to 1300
0 to 1700
0 to 1700
100 to 1800
0 to 2300
0 to 1300
0 to 90
0 to 120
0 to 165
0 to 260
-300 to 1500
-199.9 to 900.0
0.0 to 210.0
-199.9 to 900.0
0.0 to 210.0
-300 to 2300
0.0 to 900.0
-100 to 1500
0.0 to 750.0
-300 to 700
-199.9 to 700.0
-300 to 1100
-100 to 1500
-300 to 700
-199.9 to 700.0
-300 to 2300
0 to 3000
0 to 3000
300 to 3200
0 to 3200
0 to 2300
0 to 190
0 to 240
0 to 320
0 to 500
Platinum
resistance
thermometer
Temperature inputs
*The default is“5”.
*s.err will be displayed when a platinum resistance thermometer is mistakenly connected
while input type is not set for it. To clear the s.err display, correct the wiring and cycle the
power supply.
°C= c
°F= f
*3
*4
Initial setting level enables users to specify their preferred
operating conditions (input type, alarm type, control method, etc.)
*3: Refer to the adjoining tables for details of input types and alarm types.
*4: Applicable only to models with alarm functions.
*5: Operation is stopped when moved to the initial setting level.
(control/alarm are both stopped.)
*6: The grayed-out setting items are not displayed for some models and
some settings of other setting items.
*7: Applicable only to models with heater burnout functions.
*8: The four numeric digits of the product code are displayed in the No. 2
display. The setting cannot be changed and there is nothing that you
need to set.
Hold Odown
for at least
1 second
(No.1 display flashes,
then the control stops.)
Hold Odown
for at least
3 seconds
*3
*4
*3
*4
Operation Level
Set Point During
SP Ramp
*6 sp-m
0
Heater Current 1
Value Monitor
(Unit: A) *7
*6 ct1
0.0
Heater Current 2
Value Monitor
(Unit: A) *7
*6 ct2
0.0
Multi-SP
Set Point Selection
*6 m-sp
0
Remote SP Monitor
*6 rsp
0.0
Auto/Manual Switch
PID control only.
*6 a-m
Leakage Current 1
Value Monitor
(Unit: A) *7
*6 lcr1
0.0
Leakage Current 2
Value Monitor
(Unit: A) *7
*6 lcr2
0.0
Program Start
*6 prst
rset
Soak Time Remain
*6 sktr
0
RUN/STOP
*6 r-s
run
Alarm Value 1 *4
*6 al-1
0
Alarm Value Upper Limit 1
*4
*6 al1h
0
When control start = run
When control stop = stop
Operation level should normally be used during operations.
Hold Oand Mkeys
down for at least
1 second
Hold Oand Mkeys
down for at least
3 seconds
Protect Level
Restricts which settings can be displayed or changed, and
restricts change by key operation.
Press O
(less than
1 second)
Adjustment Level
Only the value set to the ins: Temperature Input Shift parameter is applied to the entire temperature input range.
When the process value is 200°C, the process value is treated as 201.2°C after input shift if the input shift value
is set to 1.2°C. The process value is treated as 198.8°C after input shift if the input shift value is set to -1.2°C.
Adjustment level is for entering set values and shift values for control.
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
* When complying with EMC standards, the line connecting the sensor must be 30 m or less.
If the cable length exceeds 30 m, compliance with EMC standards will not be possible.
Individual mounting (mm) Side-by-side mounting (mm)

mounting brackets (supplied) into the fixing slots located on the top and bottom of the rear
case.

balanced, and finally tighten them to a torque of between 0.29 and 0.39 N·m.

not exceed the specified limit.
Waterproofing is impossible
with side-by-side
installation. When
waterproofing is required, fit
watertight packing on the
backside of front panel.
°C °F
CQR
48u48
cde
Solderless terminal size
M3
OUT1 OUT1 OUT1 OUT1
OUT2
A
B
B
Conformance to EN/IEC Standards
This is a class A product.
In residential areas it may cause radio interference, in which case the user
may be required to take adequate measures to reduce interference.
Ͳ匏匶匶櫋怺殯愯暧皻柦匶沖沲
決匶匶垚櫋怺殯Ͳ匏洊沖砒洇穯匶匶嵢昢砖廪沖嬖垚斲殯沖垚決洖汊
渂汞穞柢匶愚岂彶儆洛歾汞滆櫳櫖昢斲殯穞垚冉汊徯洇求嵢穯城埪
LH
ON
OFF
SP
Communications
Monitor
*6 plcm
1234
M
Control output 1
Voltage output (for driving SSR)
12 VDC, 21 mA
Control output 2
Relay output
250 VAC, 3 A (resistive load)
Voltage output (for driving SSR)
12 VDC, 21 mA
Current output
0 to 20 mA DC

4 to 20 mA DC
Relay outputs
two outputs 250 VAC: 3 A
(resistive load)
three outputs 250 VAC: 2 A
(resistive load)
Auxiliary outputs 1, 2, and 3
3+
1+
2-
Linear current output/
voltage output (for driving SSR)
OUT1
C
OUT2
Q
CQ