Onespace 50-JN173SHLFCO User manual

Wood and Steel 3-Shelf Display, Classic Oak
ASSEMBLY INSTRUCTIONS
MODEL 50-JN173SHLFCO
SUPPLIER CODE: JNFF
For fastest service on claims, requests for replacement parts,
www.comfortproducts.net/support
e-mail: [e-mail]
Keep your sales receipt as documentation of your ownership.
CUSTOMER SERVICE
or questions, please visit our website at:
OneSpace is a Trademark of Comfort Products, Inc.
™

ASSEMBLY OVERVIEW
Shelf
weight capacity
= 110 lbs.
2

PARTSLIST
#
DESCRIPTION
STOCK #
QTY.
1 3
2 3
52
6 2
3
THE PART NUMBER CAN BE FOUND ON THE SIDE OF THE PART, EITHER STAMPED OR ON A STICKER.
ITEMS ARE NOT SHOWN TO SCALE. NOTE THAT THE BOARDS BELOW ARE SHOWN UPSIDE DOWN.
Back Board 51-JN173COBB
Shelf
Left Side Board
Back Frame
51-JN173COSH
51-JN173COSBL
51-JN173BF
Front Frame 51-JN173FF
33
Right Side Board 51-JN173COSBR 34

4
EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE.
HARDWARE KIT
PART DESCRIPTION QT Y.
A
M6 X 30MM
Bolt
Cam
24
C
D
E
24
24
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED .
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE A SCREWDRIVER BEFORE YOU BEGIN ASSEMBLING
(NOT INCLUDED).
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE A POWER DRILL.
Allen Wrench
B
1
IF YOU ARE MISSING ANY OF THESE PARTS, OR IF YOU HAVE A DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT
REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL. SIMPLY COMPLETE THE INFORMATION, INCLUDING THE PART YOU NEED. THE
PART WILL NORMALLY BE SHIPPED WITHIN 48 HOURS.
M6 X 35MM 6
STOCK # 51-JN173HA

ASSEMBLY INSTRUCTIONS
5
STEP 1
STEP 2
C x 6
2
D x 6
D x 18
C x 18
Attach the Back Board (1) to the Shelf (2) using two Bolts (C) and two Cams (D). Make sure the arrow on the cam is facing the
bolt. Using a screwdriver, turn the cam clockwise 180 degrees to lock the bolt into place. Repeat for the other two shelves.
The drawing below shows the bottom of the shelf.
Attach the Left and Right Side Boards (3 & 4) to the Shelf (2) and Back Board (1) using six Bolts (C) and six Cams (D). Repeat for
the other two shelves.
2
1
3
4
1
C
D

5
6
ASSEMBLY INSTRUCTIONS
6
STEP 3
E
A x 6
Attach the Back Frame (5) to the Front Frame (6) using three M6 x 35mm Screws (A). Repeat with the other two frames.

ASSEMBLY INSTRUCTIONS
7
STEP 4
E
B x 24
Attach the assembled shelves to the frames using twenty-four M6 x 30mm Screws (B). Note that in the drawing below the
according to which screws you are fastening.

•
•
•
8
DO NOT stand on the shelf. Do not use the shelf as a stepladder.
ed.
Every 6 months, check all bolts and screws to ensure they are tight.
Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by
Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products’ authorized dealers
as shown by the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of
parts at Comfort Products’ option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts
to be returned to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is
performed. This warranty applies under conditions of normal use and is not subject to defects caused by improper assembly or
disassembly; defects occurring after purchase due to product mo sure
to the elements; labor or assembly cost. This warranty does not cover the cost of transportation or labor. In no event shall Comfort
Products be liable in either tort or contract for any loss or direct, special, incidental, consequential or exemplary damages. This Limited
Warranty is NOT applicable to end-user customers who use Comfort Products for rental purposes. This warranty applies only to end-user
customers in the United States. All warranties are limited to the original purchaser for normal use. The weight capacity of the shelves is
110 pounds. For claims or questions concerning this warranty, please visit: www.comfortproducts.net or email us at:
[email protected]
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION
MODEL: 50-JN173SHLFCO
Comfort Products, Inc.
122 Gayoso Avenue, Suite 101
Memphis, TN 38103
Product made in China.
www.comfortproducts.net
shelf
OneSpace is a Trademark of Comfort Products, Inc.
™