Onespace 50-JN23BK8 User manual

7
,straptnemecalperrofstseuqer,smialcnoecivrestsetsafroF
www.comfortproducts.net/support
e-mail: [e-mail]
Keep your sales receipt as documentation of your ownership.
CUSTOMER SERVICE
:taetisbewruotisivesaelp,snoitseuqro
ASSEMBLY INSTRUCTIONS
MODEL 50-JN23BK8
SUPPLIER CODE: JNFF
RUSTIC INDUSTRIAL LOCKER BOOKSHELF

PARTS LIST Overview
Please look for part indicator on the side of the part. It is either stamped or on a labeled sticker.

A
PART DESCRIPTION STOCK# QTY
B
C
PARTS LIST
Please look for part indicator on the side of the part. It is either stamped or on a labled sticker.
D
E
F
G
H
I
J
K
Left Wall
Roof
Right Shelf
Cabinet Top
Divider
Right Cabinet Door
Back Board
Left Cabinet Door
Cabinet Floor Trim
Right Wall
Cabinet Floor
Left Shelf
Roof Trim
L
M
51-JN23BK8A
51-JN23BK8B
51-JN23BK8C
51-JN23BK8D
51-JN23BK8E
51-JN23BK8F
51-JN23BK8G
51-JN23BK8H
51-JN23BK8I
51-JN23BK8J
51-JN23BK8K
51-JN23BK8L
51-JN23BK8M
1
1
2
1
1
1
2
1
1
1
1
2
1

1
2
3
4
5
6
7
8
9
10
11
12
13
14
Cam Bolt & Lock Set
Door Pin
x36
x4
x4
Bracket
7x50mm Screw
x2
4x18mm Screw
x4
Door Magnet
x4
x1
Wall Anchor
Wood Peg
x32
4x14mm
x6
x25
x2
x2
x2
Nail
Washer
Door Handle
Anchor Strap
4x32mm Screw
x1
HARDWARE KIT
Stock # 51-JN23BK8HA

Start by inserting Pegs into all the following wood pieces:
Insert Pegs into the Roof (B) and Cabinet Floor (K). Then attach the related Trim pieces using
a Cam Bolt & Lock (1).
2
ASSEMBLY
1

Attach the Door Magnets (11) to the Cabinet Top (D) using two 4x14mm Screws (4) each.
Attach the Door Handles (10) to the Doors (H and F) using two 4x18mm Screws (9) each.
4
3

Attach the Cabinet Top (D) to the Divider (E) using two 7x50mm Screws (7). Sit the Roof (B) on
top of the Divider using the pegs. Connect the Left Shelves (L) using Cam & Bolt locks (1).
5

Attach what you assembled in the previous step to the Left Wall (A) using Cam Bolts & Locks (1).
Hang the Doors (F, H) between the Cabinet Top and the Cabinet Floor using door Pins (3), two for each door.
6
38
38
Use a washer (8) between the
bottom Door Pin (3) and the Cabinet Floor.
NOTE: You will use twelve Cam sets in all for this step.
The following pieces each get two: B, L, L, D, K. The Roof Trim (M)
M
B
LLD

Screw twelve Cam Bolts (1) into the Right Wall (J) and four into the Divider (E).
Then insert Cam Locks into the bottom of the Right Shelves (C). Set the Right Shelves onto the
Bolts in the Divider and tighten the locks. Then attach the Right Wall in the same manner.
E
7

8
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
5
5
5
6
6
66
6
6
6
6
Tack the back panels on with nails (6) following the pattern shown below.

Comfort Products, Inc.
122 Gayoso Avenue, Suite 101
Memphis, TN 38103
email: [email protected]
www.comfortproducts.net
• DO NOT stand on the table. Do not use the table as a stepladder.
•
• Every 6 months, check all bolts and screws to ensure they are tight.
• This products is California 93120 Compliant for Formaldehyde.
6 of 6
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR W ARRANTY INFORMATION
Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by
Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products' authorized dealers
as shown by
the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of
parts at Comfort
Products' option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts
to be returned to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is
performed. This warranty applies under conditions of normal use and is not subject to defects caused by improper assembly or
disassembly; defects occurring after purchase due to product modi cation, intentional damage, re, misuse, negligence, or exposure
to the elements;
labor or assembly cost. This warranty does not cover the cost of transportation or labor . In no event shall Comfort
Products be liable in either tort or contract for any loss
or direct, special, incidental, consequential or exemplary damages. This Limited
Warranty
is NOT applicable to end user customers who use Comfort Products for rental purposes. This warranty applies only to end-
user customers in the United States.
All warranties are limited to the original purchaser for normal use. The weight capacity is de ned as 100
pounds (unless otherwise
speci ed). For claims or questions concerning this warranty, please visit www. comfortproducts.net /support. e-
mail :
[e-mail]
MODE L : # 50-JN23BK8
table