Onespace JNFF User manual

MOBILE LAPTOP COMPUTER DESK, DUAL SURFACE, ESPRESSO
ASSEMBLY INSTRUCTIONS
MODEL # 50-JN01ES
SUPPLIER CODE: JNFF

2 OF 7
mumixamelbatpotpaL
weight capacity
=
15lbs
mumixamelbatdapesuoM
weight capacity
=
10lbs
A
B
M
JK
FF
E
D
I
N
N
CH
HG
G
G

HARDWARE KIT
STOCK # 51-JN01HA
PART DESCRIPTION QTY
STOCK NO
REPLACEMENT PARTS
IF YOU ARE MISSING ANY OF THE PARTS ABOVE, OR IF YOU HAVE A DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT
REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL. SIMPLY COMPLETE THE INFORMATION, INCLUDING THE PART YOU NEED.
THE PART WILL NORMALLY BE SHIPPED WITHIN 48 HOURS.
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED.
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE THE TOOLS BELOW BEFORE YOU BEGIN ASSEMBLING.
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
- DO NOT SHIFT OR DRAG THE PRODUCT AFTER ASSEMBLY.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE FURNITURE WAX OR POLISH AS THE UNIT
IS FINISHED WITH A PROTECTIVE CLEAR LACQUER.
1
- THE FOLLOWING TOOLS ARE NOT INCLUDED.
51-JN01ESLB
Laptop Board
A
1
51-JN01ESMB
Mouse Pad Board
B
1
51-JN01BS
Base
C
1
51-JN01BSP
Center Bar
D
1
51-JN01TSP
Top Support
E
2
51-JN01BR
Support Bar
F
PART DESCRIPTION QTY
STOCK NO
51-JN01CV
Base Cover
I
51-JN01PA
Pivot Anchor
J
1
K
M
PART DESCRIPTION QTY
PARTS AND HARDWARE LIST
EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE.
51-JN01TK
Tilt Knob
2
51-JN01SK
Support Knob
N
3
51-JN01CA
Caster
G
2
51-JN01CAL
Locking Caster
H
51-JN01UB 1
U Bracket
Washer
Wrench
Allen Key
Extra Hardware Pack
(1-5)
M6 Nut
1
1
3 OF 7
M6X35MM
M6X23MM
M6X12MM
1
2
3
4
5
6
6
4
4
2
6
7
1
1
1

ASSEMBLY INSTRUCTION
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 2
STEP 1
Screw the Locking Casters (H) into the middle legs of the Base (C). Screw the Non-locking Casters (G) into the outer legs of the Base.
Attach the Center Bar (D) to the Base using four Screws (1). NOTE: The holes at
the top of the Center Bar should be facing the shorter end of the Base.
Slide the Base Cover (I) over the Center Bar.
1X4
5X4
1
5
4 OF 7
4X2
J
X2
5
1
4
5
1
M
F
E
4 PCS
4 PCS
Attach the Pivot Anchor (J) to the Top Support (E) using the Tilt Knob (M) and two Washers (4).
Attach the Support Bars (F) to the Top Support (E) using
two Screws (1) and two M6 Nuts (5).
2 PCS
2 PCS
2 PCS
X2
D
I
C
G
G
G
H
H
The holes should face this
direction.

ASSEMBLY INSTRUCTION
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 3
STEP 4
3X4
AK
J
3
5 OF 7
Attach the Pivot Anchor (J) to the Laptop Board (A) using two Screws (3).
Attach the Top Support (E) to the Laptop Board (A) using the U Bracket (K) and two Screws (3).
2X4
B
F
2
Attach the Support Bars (F) to the Mouse Pad Board (B) using four Screws (2).
4 pcs
4 pcs

ASSEMBLY INSTRUCTION
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 5
6 OF 7
Insert the Top Support (E) into the Center Bar (D). Secure it at the desired height using the Support Knobs (N) .
N

• DO NOT stand on the desk. Do not use the desk as a stepladder.
•
• Every 6 months, check all bolts and screws to ensure they are tight.
• This products is California 93120 Compliant for Formaldehyde.
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR W ARRANTY INFORMATION
MODE L : # 50-JN01 ES
7 OF 7
Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by
Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products' authorized dealers as
shown by the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of parts at
Comfort Products' option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts to be returned
to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is performed. This warranty
applies under conditions of normal use and is not subject to defects caused by improper assembly or disassembly; defects occurring after
This warranty does not cover the cost of transportation or labor. In no event shall Comfort Products be liable in either tort or contract for
any loss or direct, special, incidental, consequential or exemplary damages. This Limited Warranty is NOT applicable to end user customers
who use Comfort Products for rental purposes. This warranty applies only to end-user customers in the United States. All warranties are
limited to the original purchaser for normal use. The weight capacity of the laptop table is 15 pounds and the capacity of the mousepad
table is 10 pounds. For claims or questions concerning this warranty, please visit www. comfortproducts.net /support or e-mail us at
[email protected]
Comfort Products, Inc.
122 Gayoso Avenue, Suite 101
Memphis, TN 38103
email: [email protected]
www.comfortproducts.net