Onespace JNFF 50-JN16DSKES User manual

LOFT WRITING DESK, ESPRESSO
ASSEMBLY INSTRUCTIONS
MODEL 50-JN16DSKES
SUPPLIER CODE: JNFF

2
Desktop maximum
weight capacity
=
150 lbs

HARDWARE KIT
STOCK # 51-JN16DSK5HA
PART DESCRIPTION QTYSTOCK NO
REPLACEMENT PARTS
IF YOU ARE MISSING ANY OF THE PARTS ABOVE, OR IF YOU HAVE A DAMAGED PART, PLEASE VISIT
WWW.COMFORTPRODUCTS.NET/SUPPORT REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL.
SIMPLY COMPLETE THE INFORMATION, INCLUDING THE PART YOU NEED. THE PART WILL NORMALLY
BE SHIPPED WITHIN 48 HOURS.
151-JN16DSK5DFDesktop Frame1
4
51-JN16DSK5LGLeg
2
1
51-JN16DSKESDTDesktop3
1
51-JN16DSK5BBBack Support Bar4
2
51-JN16DSK5SBSide Support Bar5
4
51-JN16CA5Caster6
PART DESCRIPTION QTY
PARTS AND HARDWARE LIST
EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE.
Extra Hardware Pack
M6X15MM
M6X20MM
M6X40MM
Allen Wrench
A
B
C
16
4
4
M6X12MMD 4
E1
1
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED.
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
- DO NOT SHIFT OR DRAG THE PRODUCT AFTER ASSEMBLY.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE A POWER DRILL.
3

4
ASSEMBLY INSTRUCTIONS
STEP 2
(i) Align the side support bars (5) with the legs (2).
(ii) Fasten them with four screws (A) and four screws (B).
(iii) Fasten the back support bar (4) to the side bars using four screws (C).
STEP 1
Attach the legs (2) to the desktop frame (1) using eight screws (A).
A x 8
A x 4
B x 4
C x 4
i ii iii
A
A
2
B
B
C
NOTE: Some of the screws are of similar length. Observe carefully which screw is needed before beginning each step.
4
2
A
1
5
E
E

5
ASSEMBLY INSTRUCTIONS
STEP 3
Attach the assembled frame to the desktop (3) with four screws (D) using the brackets on the desktop frame (1).
STEP 4
Screw a caster (6) into the bottom of each leg.
D x 4
3
6
E

6
MODEL: 50-JN16DSKES
SAFETY AND MAINTENANCE
•
DO NOT stand on the desk. Do not use the desk as a stepladder.
•
•
Every 6 months, check all bolts and screws to ensure they are tight.
LIMITED WARRANTY
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION
Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This
warranty is made by Comfort Products only to the original end-user customer acquiring the product directly from
Comfort Products’ authorized dealers as shown by the original sales receipt. The end-user customer remedy pursuant
to this warranty is limited to repair or replacement of parts at Comfort Products’ option within a reasonable amount of
time. Comfort Products reserves the right to require damaged parts to be returned to Comfort Products upon request.
Consent from Comfort Products must be obtained before any warranty work is performed. This warranty applies under
conditions of normal use and is not subject to defects caused by improper assembly or disassembly; defects occurring
after purchase due to product modification, intentional damage, fire, misuse, negligence, or exposure to the elements;
labor or assembly cost. This warranty does not cover the cost of transportation or labor. In no event shall Comfort
Products be liable in either tort or contract for any loss or direct, special, incidental, consequential or exemplary
damages. This Limited Warranty is NOT applicable to end-user customers who use Comfort Products for rental purpos-
es. This warranty applies only to end-user customers in the United States. All warranties are limited to the original
purchaser for normal use. The weight capacity of the desktop is 150 pounds. For claims or questions concerning this
warranty, please visit www.comfortproducts.net or email us at [email protected]
Comfort Products, Inc.
122 Gayoso Avenue, Suite 101
Memphis, TN 38103
Product made in China.
www.comfortproducts.net