Optika Italy INSPECTION SYSTEMS Series User manual

INSPECTION SYSTEMS Series
INSTRUCTION MANUAL
Model
IS-02
IS-03
Version: 1
Issued: 1.0.0

SUMMARY
1. Warning
2. Intended use
3. Package Contents
4. Overview
5. Assembly
6. Using the system
6.1 Using the base (IS-02)
6.2 Using the base (IS-03)
6.3 Using the camera (C-HAF)
Equipment disposal

1. Warning
This microscope is a scientific precision instrument designed to last for many years with a minimum of
maintenance. It is built to high optical and mechanical standards and to withstand daily use.
We remind you that this manual contains important information on safety and maintenance, and that it must
therefore be made accessible to the instrument users.
We decline any responsibility deriving from incorrect instrument use uses that does not comply with this manual.
2. Intended use
For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.
3. Package Contents
DESCRIPTION (IS-02)
QUANTITY
Base
1
Vertical pillar
1
Drop prevention ring
1
Horizontal sliding arm
1
Allen wrenches
2
Autofocus camera
1
HDMI 11,6” monitor
1
Mounting bracket
1
HDMI cable
1
SD card 16GB
1
Power supply
2
Wireless mouse
1
DESCRIPTION (IS-03)
QUANTITY
Arm
1
Desk clamp
1
Wall support
1
Spacer
1
Allen wrenches
4
Autofocus camera
1
HDMI 11,6” monitor
1
Mounting bracket
1
HDMI cable
1
SD card 16GB
1
Power supply
2
Wireless mouse
1

4. Overview
(IS-02)
(IS-03)
HORIZONTAL
STOPPER
DROP
PREVENTION
RING
HORIZONTAL
ARM SLIDING
FIXING KNOB
11,6” HDMI
MONITOR
AUTOFOCUS
CAMERA
BASE
FIXING SCREW
DESKTOP
CLAMP
DROP
PREVENTION
RING
11,6” HDMI
MONITOR
AUTOFOCUS
CAMERA

(IS-03)

(C-HAF)
HDMI CABLE
SOCKET
USB MOUSE
SOCKET
ON/OFF BUTTON
EXTERNAL
TRIGGER
SOCKET
POWER SUPPLY
SOCKET
ON/OFF LED
16GB TF CARD
SLOT

5. Assembly (IS-02)
1. Screw the pillar on the base (Fig. 1)
2. Tighten the screw to lock the pillar (Fig. 2)
3. Insert the drop preventing ring. (Fig. 3)
4. Insert the horizontal arm and lock it with the locking knob (Fig. 4 & 5)
5. Connect the camera to camera holder. Using the
provided screws attach the plate of the camera
holder to the back side of the camera (Fig. 6)
F
Fig. 6
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

i
g
.
6
6. Insert the back part of the camera holder (black
round part) ① (Fig. 7) in the hole at the end of
the horizontal arm and tighten the knob ②.
(Fig. 8).
7. Install the HDMI monitor using the provided
bracket and the provided screws.
8. Insert the provided screw into the monitor
bracket, then screw it into the threaded hole of
the horizontal arm. (Fig. 8)
Fig.9
9. Connect HDMI cable from camera to monitor,
insert SD card into the camera slot, connect
USB mouse then plug the power supplies
(camera and monitor). (Fig. 9)
10. Press the “ON/OFF” button on the camera to
turn on the camera. LED will turn from red to
blue (Fig. 10)
Fig. 8
Fig. 9
Fig. 10
①
②
Fig. 7
①
②

5. Assembly (IS-03)
1. Mount the camera on to the arm, using the
provided screws and allen wrench. (Fig. 11)
2. Install the HDMI monitor on to the arm using the
provided screws and allen wrench. (Fig. 12)
3. Connect HDMI cable from camera to monitor,
insert SD card into the camera slot, connect
USB mouse then plug the power supplies
(camera and monitor). (Fig. 13)
4. Press the “ON/OFF” button ①on the camera to
turn on the camera. LED ② will turn from red to
blue. (Fig. 14)
Fig. 11
Fig. 13
Fig. 14
Fig. 12
①
②

Desk installation
1. Adjust the height of the Desk Clamp ② to suit desktop
surface. (Fig. 15)
2. Attach the desk clamp ② on to the edge of the desk in the desired position and with the clamp opening
facing towards the edge of desktop. Tighten by hand to ensure that the desk clamp fully clamps to the
desktop surface and is secure.
3. To position the collar at your desired height, you will need to loosen the collar as shown. Tighten by hand
until the collar is firmly in place.
Fig. 15