Optika Italy SZ-STL5 User manual

Version: 3
Issued: 01, 12, 2014
Model
SZ-STL5
SZ-STL5LED
Modular Series
INSTRUCTION MANUAL

Page 2
Table of Contents
Warning
Intended use
Package Contents
Product specifications
Assembly
Overview
Installation to desk
Adjusting the Mount Bracket Resistance
Equipment disposal

Page 3
Warning
This microscope is a scientic precision instrument designed to last for many years with a minimum of mainte-
nance. It is built to high optical and mechanical standards and to withstand daily use.
We remind you that this manual contains important information on safety and maintenance, and that it must
therefore be made accessible to the instrument users.
We decline any responsibility deriving from incorrect instrument use uses that does not comply with this manual.
Intended use
For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.
Package Contents
DESCRIPTION QUANTITY
Arm 1
Focus with knobs 1
Desk clamp 1
Wall support 1
Spacer 1
Allen wrenches 4
Illuminator arm (SZ-STL5LED) 2
Control box (SZ-STL5LED) 1
Power supply 6v (SZ-STL5LED) 1

Page 4
Product specications
Weight Capacity: 3kg~8kg.
Maximum Extension: 577mm.
Depth from Pole
(Closed): 75mm.
Tilt adjustment: +/-90 degree.
Swing adjustment: +/-90 degree
Pivot: 360/180/360 degree.
SZ-STL5LED
Stand: with white X-LED3 incident illumination system.
Intensity control using two dedicated knobs.
LED power: 3.5W (x2), each comparable to a 50W halogen bulb.
Color temperature: 6300K
LED average lifetime: approx. 50000h.
Provided power supply: 6V 2,5A
Assembly (SZ-STL5)
Mount the focus on to the arm, using the provided screws and allen wrench.

Page 5
Overview

Page 6
Installation to desk
1. Adjust the height of the Desk Clamp (2) to suit desktop surface (See Figure 1)
Figure 1
2. Attach the Desk Clamp (2) on to the edge of the desk in the desired position and with the clamp opening fac-
ing towards the edge of desktop (See Figure 2). Tighten by hand to ensure that the Desk Clamp fully clamps
to the desktop surface and is secure (See Figure 3).
Figure 2 Figure 3
3. To position the Collar at your desired height, you will need to loosen the Collar as shown. Tighten by hand
until the Collar is rmly in place (See gure 4)
Figure 4
UP
DOWN
DETAILED VIEW
COLLAR

Page 7
Adjusting the Mount Bracket Resistance
1. Product is brilliantly engineered to control the resistance in the Tilter Mount Bracket to suit swing side to side
of 90 degree and tilt forward and backward of 90 degree. It is possible to control the amount of resistance in
the Tilter Mount Bracket.
2. If the Tilter Mount Bracket tends to automatically fall, it may be required to adjust the Tilter Mount Bracket
joint to suit your microscope tilt position of forward and backward of 90 degree. This can be done by using
Hex Allen Wrench 6mm to increase the resistant of the Tilter Mount Bracket in order to secure tilt position,
adjust the M5x15mm Tension Hex Socket Cap Screw located around the Tilter Mount Bracket Joint using
6mm Hex Allen Wrench. (See Figure 5).
Figure 5
3. To increase or decrease the resistance of the Pivot Joint to suit microscope swing side to side, adjust the
Tension Hex Cap Screw located on front side of the Articulating Arm to secure the position. (See Figure 6).
4. To increase the resistance, tighten the M5x15mm Tension Hex Cap Screwn using Allen Wrench 4mm in a
clockwise direction. To decrease the resistance, loosen the M5x15mm Tension Hex Cap Screw using Allen
Wrench 4mm supplied in an anti-clockwise direction.
Figure 6
DETAILED VIEW
DETAILED VIEW
PIVOT JOINT
MICROSCOPE SWING-SIDE TO SIDE

Page 8
5. This production can be lift up and down as shown. (See Figure 7). If this product tends to automatically move
to side, it may be required tension adjustment on the Articulating Arm to suit your microscope arm swing to
side position. This can be done by using Hex Allen Wrench 2.5mm supplied. (See Figure 8).
Figure 7
Figure 8

Page 9
Equipment disposal
Art.13 Dlsg 25 july 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating
to the reduction in the use of hazardous substances in electrical and electronic equipment and waste disposal.”
The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be
collected separately from other waste.
The separate collection of this equipment at the end of its lifetime is organized and managed by the producer.
The user will have to contact the manufacturer and follow the rules that he adopted for end-of-life equipment
collection.
The collection of the equipment for recycling, treatment and environmentally compatible disposal, helps to prevent
possible adverse effects on the environment and health and promotes reuse and/or recycling of materials of the
equipment.
Improper disposal of the product involves the application of administrative penalties as provided by the laws in force.