Opus CS 2208 CD User manual

User’s guide CS 2208 CD
User’s guide
CS 2208 CD

User’s guide CS 2208 CD
Health & Safety precautions:
•Before using, the equipment please read the Health & Safety precautions, manufacturers’ recommendations and
the operating manual.
•The operating manual should be available at all times for the operator to read.
• The equipment can only be used in accordance with the specifications in the user guide/manual.
•should be installed on a sturdy and level surface near a 220 to 240 V AC socket.
•the socket should be earthed in accordance with electrical regulations.
•must be protected against moisture and dust.
•Do not put the equipment near heating or ventilation units.
•The equipment must not be used in or near a room with inflammable liquids or gases.
•Do not use the equipment near aerosols of, oil or grease made from petroleum or inflammable substances.
•Do not use compressed air from a aerosol for clearing shredder.
•The power supply cable should be protected against any damage and not be used to pull the equipment or to
remove the plug from the power socket.
•Unplug the equipment from the power socket when removing the cover or cleaning the inside.
•The equipment should be kept away and out of reach of children and animal’s.
•Danger! Equipment contains rotary elements. Keep away, long hair, loose jewellery, ties and other loose pieces of
clothing as they can become entangled in the cutting head.
•Be careful when feeding material into the slots.
• When the motor overheats, it will turn off without a single, turn off the main switch of the shredder immediately and wait
for it to cool down!
•Do not put any heavy objects on the device!
•When any malfunction occurs, check that the equipment is being used correctly and then contact the dealer or
service point.
•The equipment must not be put or kept outside and should be operated in a room temperature higher than +8°C.
•The equipment should be operated accordance to the general Health & Safety rules.
•Any repairs must be carryout by only authorised staff.
• After using the shredder, it must be turned off by the main switch or by unplugging it from the power socket.
Recommendations:
•The equipment was designed for shredding paper, credit cards and CD/DVDs.
•During longer none operation, the mains switch should be turned “OFF’ and unplugged.
•Empty the shredded waste from the bin frequently
•The shredder can only be operated with the original paper bin supplied.
•To ensure long and faultless use of the equipment do not shred more than 8 sheets of 80gram/m² paper at one time.
•Do not shred computer continues printout paper, PVC foil, coated paper or cardboard as it can damage of cutting
knifes and mechanism and over load the electric motor.
•The shredder is able to deal with light staples and paper clips
NOTE! Not complying with the recommendations above can result,
with the guarantee/warranty being made void.

User’s guide CS 2208 CD
Budowa urządzenia
1 – Orange diode for REVERSE mode
2 – Red diode for overheat machine
3 – Feeding slot for credit cards/ DC/DVDs
4 – Feeding slot for paper
5 – Waste bin for destroyed credit cards / CD/DVDs
6 – Waste bin
7 – Transparent window
8 – Castors
9 – Housing
10 – Main switch
11 – Slider FWD/Auto/REV
12 – Green diode for rediness to work

User’s guide CS 2208 CD
Operation:
•The equipment should be placed on a level floor
•Before plugging in the equipment, ensure that main switch is in “0” position
•Set the main switch into „I” position – green diode will be on
•Insert paper into the feed slot on the top. NOTE! Paper should be only put in the middle of the slot
•The equipment will start automatically after inserting the paper
•Maximum paper width of 220mm. If the pages are wider, cut or fold to fit the slot. You can only shred 8 sheets of 80
g/m² paper at a time
•Shredding credit cards. The shredder shreds only one credit card or one CD/DVD at a time
•It is impossible to shred paper and credit cards or CD/DVDs at the same time
•After 10 minutes of continues work electric motor will overheat and machine stop immediately. Red diode will be on.
Wait 20 minutes until it cools down
•Turn the power switch off when shredding is finished
•If too many pages of paper are inserted into the slot, it will cause the paper to jam inside the cutting blades
•Pull out the surplus jammed/stuck paper and slide the switch to REV to (reverse) the paper out and then switch to
“FWD” (forward) to shred any paper scraps left in the cutting blades
•If it will not solve the problem, contact the dealer or the service team
Cleaning:
• Before clearing the shredder ensure that the main power switch is switch off then unplug the equipment from the
mains socket
•When the shredded paper bin gets overfilled, it may cause problems and paper will go inside the mechanism feed
and there is a risk of fire. Pull the bin out, remove shreds and re-install the bin under the shredder
•To avoid problems please clean the shred bin regularly before it overfills
•Cleaning the housing. Wipe the cover of the shredder with gentle home detergent or a damp piece of cloth.
•Do not put the equipment into water
•Do not wipe the unit with petroleum, thinners, alcohol or solvents “” they can cause permanent damage to the
housing and the plastic
Maintenance:
•To prevent reduction of efficiency, increased sound levels and to prolong the lifespan of the
equipment, it is necessary to oil cutting blades regularly.
•After filling the waste bin several times, the blades should be oiled with a special oil (provided by OPUS).
•Put a little oil on a few pieces of paper and shred them so that the oil will spread on the whole cutting mechanism.
Possible malfunctions
Malfunction Possible Cause Remedy
Equipment does
not start after
inserting paper into
the slot
1. Not plug in properly
2. Pages to be shred are too soft
3. Overheating
4. Paper jam
5. The basket is not installed
properly
1. Plug the equipment in correctly
2. Fold pages or insert more paper in the feed
opening
3. Turn off the shredder, wait about 30 min
Turn on once again
4. Remove stuck paper
5. Install shred bin correctly
Equipment does not
stop after shredding
Photo cell in the entry slot is
covered by scraps of paper
Clean the photo cell
The shredder
operates too loud
Equipment is not on sturdy and level
floor
Place the machine on study and level surface
and lock front wheels

User’s guide CS 2208 CD
The shredder does
not operate
correctly
1. Too many pages inserted into the
feed opening
2. Too big a paper format
3. Paper is not inserted in the centre
of feed opening
1. Reduce number of pages inserted to the slot at
one time
2. Switch to REV button to remove paper and insert
folded pages once again
3. Insert paper in the middle of the feed opening
Technical Data:
Shredder type: cross-cut
Feed opening: 220mm / 122mm
Performance: 8* / 1 CD / 1 credit card
Shred size: 2x12mm
Waste bin: 22l
Voltage: 230 V / 50 Hz
Power: 260 W
Input current: 1,1 A
Net weight: 10,3 kg
Dimensions (HxWxD): 565 x 350 x 260 mm
*paper 80g/m²
17.04.2013
distributor: OPUS Sp. z o.o. ●ul. Toruńska 8 ●44 – 122 Gliwice ●www.opus.pl