Oregon Scientific RMR383HG User manual

EN
1
Digital Thermometer with Humidity, Ice
Alert and Radio-controlled Clock
Model: RMR383HG
USER MANUAL
CONTENTS
Introduction............................................................... 2
Clock Overview......................................................... 2
Front View................................................................ 2
Back View................................................................ 3
LCD Display............................................................. 4
Remote Sensor (THN132N) .................................... 5
Getting Started.......................................................... 5
Batteries................................................................... 5
Remote Sensor ......................................................... 5
Sensor Data Transmission....................................... 7
Clock ......................................................................... 7
Clock Reception....................................................... 7
Reception Signal ..................................................... 7
Set Clock ................................................................. 7
Alarm ......................................................................... 8
Temperature and Humidity ...................................... 8
Temperature and Humidity Trend ............................ 9
Ice Warning ............................................................. 9
Hi / Lo Temperature / Humidity Alarm...................... 9
Heat Index ................................................................. 9
Comfort Zone.......................................................... 10
Moon Phase ............................................................ 10
Reset........................................................................ 11
Precautions............................................................. 11
Specications ......................................................... 11
About Oregon Scientic ........................................ 12
EU-Declaration Of Conformity............................... 12
RMR383HG_M_EN_op1.indd 1 15-9-24 ��2:13

EN
2
INTRODUCTION
Thank you for selecting this Oregon ScienticTM Digital
Thermometer with Humidity, Ice Alert and Radio-
controlled Clock (RMR383HG). This clock is supplied
with a remote sensor (THN132N) and can support up to
3 sensors in total (additional sensors sold separately).
NOTE Please keep this manual handy as you use
your new product. It contains practical step-by-step
instructions, as well as technical specifications and
warnings you should know about.
CLOCK OVERVIEW
FRONT VIEW
1
2
3
4
1. SNOOZE
2. Temperature and Humidity Area
3. Clock / Alarm Area
4. : View alarm status; set alarm
RMR383HG_M_EN_op1.indd 2 15-9-24 ��2:13

EN
3
BACK VIEW
15
6
7
10
8
9
2
3
4
1. / :Increase / decrease setting; activate /
deactivate clock reception signal
2. MODE: Change settings / display
3. CHANNEL: Switch remote sensor display
4. MEM: View current, maximum and minimum
temperature / humidity
5. °C / °F: Select temperature unit
6. HEAT INDEX
7. TEMP / HUMIDITY HI / LO : Change settings
or enable / disable hi or lo temperature / humidity
alarm
8. RESET: Reset unit to default settings
9. EU / UK switch
10. Battery compartment
RMR383HG_M_EN_op1.indd 3 15-9-24 ��2:13

EN
4
1
9
10
11
12
13
14
2
3
4
5
6
7
8
LCD DISPLAY
Clock / Alarm area:
1. Clock signal reception
2. AM / PM mode selected
3. Alarm mode
4. Alarm set
5. AM / PM mode selected
6. Alarm time
7. Clock
8. Moon phase
Temperature and Humidity area:
1. Heat index icon
2. Hi / lo temperature alarm
3. Max / min temperature icon
4. Sensor reception icon
5. Comfort Zone
6. Battery low icon
7. Hi / lo humidity alarm
8. Max / min humidity icon
9. Ice warning is active
10. Temperature trend
11. Temperature
12. Heat Index warning
13. Humidity trend
14. Humidity
RMR383HG_M_EN_op1.indd 4 15-9-24 ��2:13

EN
5
REMOTE SENSOR (THN132N)
1. LED indicator 1. Wall mount
2. Battery compartment
3. Battery door
4. Table stand
5. RESET
6. CHANNEL switch
1
2
3
4
6
5
1
GETTING STARTED
BATTERIES
Insert batteries before first use, matching the polarity
(+ and -). Press RESET after each battery change.
indicates main unit batteries are low.
NOTE Do not use rechargeable batteries. We
recommend that you use alkaline batteries with this
product for longer usage and lithium batteries in
temperatures below freezing.
REMOTE SENSOR
The sensor collects temperature readings approx. every
40 seconds and sends them to the main unit. The main
unit can collect data from up to 3 sensors.
RMR383HG_M_EN_op1.indd 5 15-9-24 ��2:13

EN
6
To set up the sensor:
1. Slide open the battery door.
2. Insert the batteries, matching the polarity (+ / -).
Press RESET after each battery change.
3. Select a channel. Make sure you use a different
channel for each sensor.
4. Close the battery compartment.
5. Secure the sensor in the desired location using the
wall mount or table stand.
For best results:
• Place the sensor out of direct sunlight and
moisture.
• Do not place the sensor more than 30 m (100 ft) from
the main (indoor) unit.
• Position the sensor so that it faces the main (indoor)
unit, minimizing obstructions such as doors, walls,
and furniture.
• Place the sensor in a location with a clear view to
the sky, away from metallic or electronic objects.
• Position the sensor close to the main unit during
cold winter months as below-freezing temperatures
may affect battery performance and signal
transmission.
The transmission range may vary depending on many
factors. You may need to experiment with various
locations to get the best results.
Standard Alkaline batteries contain signicant amounts of
water. Because of this they will freeze in low temperatures
of approximately -12°C (10°F). Disposable Lithium batteries
have a much lower threshold for temperature with an
estimated freezing range of below -30°C (-22°F).
Wireless ranges can be impacted by a variety of factors
such as extremely cold temperatures. Extreme cold
may temporarily reduce the effective range between the
sensor and the base station. If the unit’s performance
fails due to low temperature, the unit will resume proper
functioning as the temperature rises to within the normal
temperature range (i.e. no permanent damage will occur
to the unit due to low temperatures).
RMR383HG_M_EN_op1.indd 6 15-9-24 ��2:13

EN
7
SENSOR DATA TRANSMISSION
The sensor reception icon in the temperature and
humidity area shows the status.
ICON DESCRIPTION
Main unit is searching for the
sensor(s)
A channel has been found
and sensor signal is being
received
and “- - . -“ The sensor cannot be found.
(Temperature Search for the sensor or
and Humidity Area) check batteries
To search for a sensor:
Simultaneously, press and hold MEM and CHANNEL
for 2 seconds.
NOTE If the sensor is still not found, check the batteries,
obstructions, and remote unit location.
RECEPTION SIGNAL
Clock signal reception indicator:
STRONG SIGNAL WEAK SIGNAL NO SIGNAL
To enable and force a signal search:
Press and hold for 2 seconds.
To disable the signal reception:
Press and hold for 2 seconds.
SET CLOCK
If the clock signal reception is enabled and a signal is
being received the clock does not need to be manually
set.
To manually set the clock:
1. Press and hold MODE for 2 seconds.
CLOCK
CLOCK RECEPTION
This product is designed to synchronize its date and time
automatically once it is within range of :
• DCF77 generated from Frankfurt, Germany for
Central Europe.
• MSF60 generated from Rugby, England.
The clock collects the radio signals whenever it is within
1500 km (932 miles) of a signal.
NOTE Slide the EU / UK switch to appropriate position
for your location. Repeat each time you reset the unit.
NOTE Initial reception takes 2-10 minutes for rst set
up or when RESET is pressed. Once complete, the
reception icon will stop blinking. If the signal is weak, it
can take up to 24 hours to get a valid signal.
RMR383HG_M_EN_op1.indd 7 15-9-24 ��2:13

EN
8
2. Press and to change the settings.
3. Press MODE to conrm.
4. The setting sequence is: time zone offset, 12/24 hour
format, hour, minute, year, month, date, and display
language.
NOTE The time zone offset can be used to set the
clock up to + / - 9 hours from the received clock signal
time. If you have disabled the clock signal reception (i.e.
manually setting the clock), do not set a value for time
zone offset.
NOTE The language options are English (E), German
(D), French (F), Italian (I), and Spanish (S).
To switch the clock display:
Press MODE to toggle between:
• Clock with day
• Clock with seconds
ALARM
To set the alarm:
1. Press and hold ALARM for 2 seconds.
2. Press / to set alarm time.
3. Press MODE to conrm. indicates alarm is ON.
To toggle alarms ON / OFF:
1. Press ALARM to display alarm time.
2. Press ALARM again to turn alarm ON / OFF.
To silence the alarm:
• Press SNOOZE to silence it for 8 minutes.
OR
• Press any key except SNOOZE to turn the alarm off
and activate it again after 24 hours.
TEMPERATURE AND HUMIDITY
To toggle temperature unit:
Press °C / °F.
To view outdoor sensors temperature readings:
Press CHANNEL.
To auto-scan between sensors:
Press and hold CHANNEL for 2 seconds. Each sensor’s
data is displayed for 3 seconds.
To end auto-scan:
Press CHANNEL or MEM.
To toggle between current, minimum and maximum
records for the selected sensor:
Press MEM repeatedly.
To clear the records:
Press and hold MEM for 2 seconds.
RMR383HG_M_EN_op1.indd 8 15-9-24 ��2:13

EN
9
TEMPERATURE AND HUMIDITY TREND
The temperature and humidity trend icons are based
on recent readings.
RISING STEADY FALLING
ICE WARNING
If the channel 1 sensor falls between 3°C to –2°C (37°F
to 28°F), ashes to warn you that the temperature is
approaching freezing.
NOTE The warning will automatically stop if the
temperature goes outside the ice-warning range.
HI / LO TEMPERATURE / HUMIDITY ALARM
An alarm can be set to sound if sensor set to channel
1 records above or below a temperature / humidity of
your choice.
To set alarm ON/OFF:
1. Press and hold TEMP / HUMIDITY HI / LO .
2. Use and to select high / low temperature /
humidity alarm. Press TEMP / HUMIDITY HI / LO
to conrm.
3. Press / to set alarm ON / OFF and press TEMP
/ HUMIDITY HI / LO to conrm.
4. If alarm has been activated, use and to select
the temperature / humidity.
5. Press TEMP / HUMIDITY HI / LO to conrm.
To silence the alarm:
Press any key. The alarm resets automatically and will
resound if the hi / lo temperature selected is exceeded
again.
NOTE The THN132N sensor supplied does not support
humidity readings. To enable Hi / Lo Humidity alarm
a thermo-hygro sensor must be purchased and set
to channel 1. For further information on compatible
sensors such as the THGR268 thermo-hygro sensor
please check with your local retailer or go to www.
oregonscientic.com.
HEAT INDEX
The heat index combines temperature and humidity data
to describe the actual temperature felt. The THN132N
sensor supplied does not support heat index display. A
thermo-hygro sensor must be purchased to enable heat
index display for channels 1-3.
RMR383HG_M_EN_op1.indd 9 15-9-24 ��2:13

EN
10
WARNING HEAT INDEX MEANING
Extreme danger 54.5°C (130°F) Strong risk of
or above dehydration / sun
stroke
Danger 40.5 - 54°C Heat exhaustion
(105 - 129°F) likely
Extremecaution 32.2 - 40°C Possibility of heat
(90 - 104°F) dehydration
Caution 26.6-31.7°C Possibility of heat
(80- 89°F) exhaustion
• To display the heat index, press HEAT INDEX.
• To toggle between current / maximum / minimum
readings, press HEAT INDEX, then press CHANNEL
to select channel 1-3 or indoor, followed by MEM.
• To toggle between temperature / humidity and heat
index display, press and hold HEAT INDEX for 2
seconds. Press HEAT INDEX again to stop this
feature.
NOTE
If the heat index is below 80°F / 26°C, if the
selected sensor does not support humidity measurement
or if the channel is not working, the heat index will display
NA .
COMFORT ZONE
The comfort zone assesses the climate based on current
temperature and humidity measurements.
ICON TEMPERATURE HUMIDITY
Any > 70%
20 - 25°C (68 - 77°F) 40 - 70%
Any < 40%
MOON PHASE
• When calendar is set press or to view the moon
phase for the next / previous day.
• Press and hold or to scan through the years
(2001 to 2099).
New Moon
Waxing Crescent
First quarter
Waxing Gibbous
Full Moon
Waning Gibbous
Last quarter
Waning Crescent
RMR383HG_M_EN_op1.indd 10 15-9-24 ��2:13

EN
11
RESET
Press RESET to return the unit to the default settings.
PRECAUTIONS
This product is engineered to give you years of
satisfactory service if you handle it carefully. Here are
a few precautions:
• Do not subject the unit to excessive force, shock,
dust, temperature or humidity, which may result in
malfunction, shorter electronic life span, damaged
battery and distorted parts.
• Do not immerse the unit in water. If you spill liquid
over it, dry it immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive
materials.
• Do not tamper with the unit’s internal components.
Doing so will invalidate the warranty on the unit and
may cause unnecessary damage. The unit contains
no user-serviceable parts.
• Only use fresh batteries as specied in the user’s
instructions. Do not mix new and old batteries.
• Due to printing limitations, the displays shown in this
manual may differ from the actual display.
• The contents of this manual may not be reproduced
without the permission of the manufacturer.
• Do not dispose this product as unsorted municipal
waste. Collection of such waste separately for
special treatment is necessary.
NOTE The technical specications for this product and
the contents of the user manual are subject to change
without notice.
SPECIFICATIONS
TYPE DESCRIPTION
MAIN UNIT
L x W x H 110 x 69 x 140 mm
(4.3 x 2.7 x 5.5 in)
Weight 153 g (5.34 oz) without battery
Temperature unit °C / °F
Temperature range -5°C to 50°C (23°F to 122°F)
Resolution 0.1°C (0.2°F)
Clock frequency DCF-77 (EU) / MSF-60 (UK)
Synchronization Auto or disabled
Signal frequency 433 MHz
Clock Auto or manual (disabled)
Humidity range 25% - 95%
Humidity resolution 1%
MEM Min / Max relative humidity and
temperature
Alarm duration 2 minutes
Snooze 8 minutes
Clock display HH:MM:SS
HH:MM:Day of Week
Hour format 12 / 24 hour format
RMR383HG_M_EN_op1.indd 11 15-9-24 ��2:13

EN
12
COUNTRIES RTTE APPROVAL COMPLIED
Calendar DD / MM language
selectable: E, D, F, I and S
Power 2 x UM-3 (AA) 1.5 V batteries
REMOTE UNIT
L x W x H 96 x 50 x 22 mm
(3.8 x 2.0 x 0.9 in)
Weight 62 g (2.22 oz) without battery
Transmission range 30 m (100 ft) unobstructed
Temperature range -30°C to 60°C (-22°F to 140°F)
Power 1 x UM-3 (AA) 1.5 V battery
www2.oregonscientic.com/service/default.asp
OR
Call 1-800-853-8883.
For international inquiries, please visit:
www2.oregonscientic.com/about/international.asp
EU-DECLARATION OF CONFORMITY
Hereby, Oregon Scientic, declares that the Digital
Thermometer with Humidity, Ice Alert and Radio-
controlled Clock (Model RMR383HG) is in compliance
with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
A copy of the signed and dated Declaration of Conformity
is available on request via our Oregon Scientific
Customer Service.
NOTE It is recommended that you use alkaline batteries
with this product for longer performance.
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientic.com) to learn
more about Oregon Scientic products such as digital
cameras; MP3 players; children’s electronic learning
products and games; projection clocks; health and
tness gear; weather stations; and digital and conference
phones. The website also includes contact information
for our Customer Care department in case you need
to reach us, as well as frequently asked questions and
customer downloads.
We hope you will nd all the information you need on our
website, however if you’re in the US and would like to
contact the Oregon Scientic Customer Care department
directly, please visit:
All EU Countries, Switzerland CH
and Norway N
RMR383HG_M_EN_op1.indd 12 15-9-24 ��2:13

EN
13
Digital Thermometer with Humidity,
Ice Alert and Radio-controlled Clock
MODEL: RMR383HG
User Manual
RMR383HG_M_EN_op1.indd 13 15-9-24 ��2:13

EN
14
© 2006 Oregon Scientic. All rights reserved
086L004440-015
RMR383HG_M_EN_op1.indd 14 15-9-24 ��2:13

DE
1
Digitales Thermometer mit
Luftfeuchtigkeit, Frostalarm und
funkgesteuerter Uhr
Modell: RMR383HG
BEDIENUNGSANLEITUNG
INHALT
Einleitung ................................................................. 2
Übersicht .................................................................. 2
Vorderansicht .......................................................... 2
Rückansicht ............................................................ 3
LCD-Anzeige .......................................................... 4
Funksendeeinheit (THN132N) ................................ 5
Erste Schritte ........................................................... 5
Batterien ................................................................. 5
Externe Funksendeeinheit ...................................... 5
Datenübertragung der Funksendeeinheit ............... 7
Funkuhr ..................................................................... 7
Zeitsignalempfang .................................................. 7
Empfangssignal ....................................................... 7
Die Uhr einstellen ................................................... 8
Alarm ........................................................................ 8
Temperatur und Luftfeuchtigkeit ............................ 8
Frostwarnung .......................................................... 9
Min / Max Temperatur- und Luftfeuchtigkeitsalarm ......9
Hitzeindex (optional) ............................................. 10
Komfortzone .......................................................... 10
Mondphase ............................................................. 10
Reset ....................................................................... 11
Vorsichtsmaßnahmen ............................................ 11
Technische Daten ................................................... 12
Über Oregon Scientic........................................... 12
EG-Konformitätserklärung .................................... 13
RMR383HG_M_DE_op1.indd 1 15-9-24 2:12

DE
2
EINLEITUNG
Wir danken Ihnen, dass Sie sich für das digitale
Thermometer mit Luftfeuchtigkeit, Frostalarm
und funkgesteuerter Uhr von Oregon Scientific™
(RMR683HG) entschieden haben. Dieses Thermometer
wird mit einer externen Funksendeeinheit (THN132N)
geliefert und kann insgesamt bis zu 3 Funksendeeinheiten
unterstützen (zusätzliche Funksendeeinheiten sind
gesondert erhältlich).
HINWEIS Halten Sie bitte diese Anleitung bereit, wenn
Sie Ihr neues Produkt verwenden. Sie enthält praktische
Schritt-für-Schritt-Anweisungen sowie technische Daten
und für Sie wichtige Warnhinweise.
ÜBERSICHT
VORDERANSICHT
1. SNOOZE
2. Temperatur- und Luftfeuchtigkeits-Bereich
3. Uhr- / Alarmbereich
4. : Alarmstatus anzeigen; Alarm einstellen
1
2
3
4
RMR383HG_M_DE_op1.indd 2 15-9-24 2:12

DE
3
RÜCKANSICHT
1. / :Einstellung erhöhen / verringern; Zeitsignalempfang
aktivieren / deaktivieren
2. MODE: Einstellungen / Anzeige ändern
3. CHANNEL: Funksendeeinheit anzeigen
4. MEM: Aktuelle, maximale und minimale Temperatur /
Luftfeuchtigkeit anzeigen
5. °C / °F: Temperatureinheit auswählen
6. HEAT INDEX Hitzeindex
7. TEMP / HUMIDITY HI / LO : Einstellungen ändern
oder Alarm für hohe / niedrige Temperatur /
Luftfeuchtigkeit aktivieren / deaktivieren
8. RESET: Gerät auf Standardeinstellungen
zurücksetzen
9. EU- / UK-Schalter
10. Batteriefach
15
6
7
10
8
9
2
3
4
RMR383HG_M_DE_op1.indd 3 15-9-24 2:12

DE
4
1
9
10
11
12
13
14
2
3
4
5
6
7
8
1
7
8
2
3
4
5
6
LCD-ANZEIGE
1. Symbol für Hitzeindex
2. Alarm für min. / max. Temperatur
3. Symbol für min. / max. Temperatur
4. Funksendeeinheit-Empfangssymbol
5. Komfortzone
6. Symbol für schwache Batterie
7. Alarm für min. / max. Luftfeuchtigkeit
8. Symbol für min. / max. Luftfeuchtigkeit
9. Frostwarnung ist aktiv
10. Temperaturtrend
11. Temperatur
12. Warnanzeige für Hitzeindex
13. Luftfeuchtigkeitstrend
14. Luftfeuchtigkeit
Uhr- / Alarmbereich:
1. Zeitsignalempfang
2. AM- / PM-Modus ausgewählt
3. Alarmmodus
4. Alarm ist eingestellt
5. AM- / PM-Modus ausgewählt
6. Alarmzeit
7. Uhrzeit
8. Mondphase
Temperatur- und Luftfeuchtigkeitsbereich:
RMR383HG_M_DE_op1.indd 4 15-9-24 2:12

DE
5
1
FUNKSENDEEINHEIT (THN132N)
1. LED-Indikator 1. Wandhalterung
2. Batteriefach
3. Batteriefachklappe
4. Tischaufsteller
5. RESET
6. CHANNEL-
Kanalwahlschalter
ERSTE SCHRITTE
BATTERIEN
Legen Sie die Batterien vor der ersten Verwendung ein und
achten Sie auf die Übereinstimmung der Polarität (+ und -).
Nach jedem Batteriewechsel auf RESET drücken.
gibt an, dass die Ladung der Batterien schwach ist.
HINWEIS Verwenden Sie keine wiederaufladbaren
Batterien. Wir empfehlen Ihnen, für dieses Produkt
Alkaline-Batterien für eine längere Betriebsdauer
und Lithium-Batterien für Temperaturen unter dem
Gefrierpunkt zu verwenden.
EXTERNE FUNKSENDEEINHEIT
Die Funksendeeinheit empfängt etwa alle 40 Sekunden
Temperaturmesswerte und sendet diese an die
Basiseinheit. Die Basiseinheit kann Daten von bis zu 3
Funksendeeinheiten empfangen.
1
2
3
4
6
5
RMR383HG_M_DE_op1.indd 5 15-9-24 2:12

DE
6
So stellen Sie die Funksendeeinheit ein:
1. Öffnen Sie die Batteriefachklappe.
2. Legen Sie die Batterien ein und achten Sie auf die
Übereinstimmung der Polarität (+ / - ). Nach jedem
Batteriewechsel auf RESET drücken.
3. Wählen Sie einen Kanal aus. Stellen Sie sicher, dass Sie für
jede Funksendeeinheit einen eigenen Kanal verwenden.
4. Schließen Sie das Batteriefach.
5. Befestigen Sie die Funksendeeinheit mit der
Wandhalterung oder dem Tischaufsteller an der
gewünschten Stelle.
Für optimale Ergebnisse:
• Platzieren Sie die Funksendeeinheit so, dass sie
vor direkter Sonnenbestrahlung und Feuchtigkeit
geschützt ist.
• Platzieren Sie die Funksendeeinheit nicht weiter als
30 Meter von der Basiseinheit (im Haus) entfernt.
• Positionieren Sie die Funksendeeinheit so, dass sie auf die
Basiseinheit (im Haus) ausgerichtet ist, und vermeiden Sie
Hindernisse wie Türen, Wände und Möbel.
• Platzieren Sie die Funksendeeinheit an einem
Standort mit freier Sicht auf den Himmel und
stellen Sie ihn nicht in die Nähe von metallischen
Gegenständen oder elektronischen Geräten.
• Positionieren Sie die Funksendeinheit während der
kalten Wintermonate in der Nähe der Basiseinheit,
da Temperaturen unter der Frostgrenze die
Batterieleistung und die Signalübertragung
beeinträchtigen können.
Die Übertragungsreichweite kann von mehreren
Faktoren abhängen. Sie müssen eventuell mehrere
Standorte testen, um optimale Ergebnisse zu erzielen.
HandelsüblicheAlkaline-Batterien enthalten beträchtliche
Mengen Wasser. Daher können diese bei niedrigen
Temperaturen ab etwa –12°C (10°F) einfrieren. Die
Temperaturgrenze von Lithium-Einwegbatterien
ist weitaus niedriger und weist einen geschätzten
Frostbereich von unter -30°C (-22°F) auf.
Die Übertragungsreichweite von Funksignalen kann
von verschiedenen Faktoren, wie extrem niedrige
Temperaturen, beeinflusst werden. Extreme Kälte
kann die effektive Übertragungsreichweite zwischen
Funksendeeinheit und Basisstation vorübergehend
verringern. Sollten Funktionsstörungen am Gerät
aufgrund niedriger Temperaturen auftreten, so wird
das Gerät wieder ordnungsgemäß funktionieren, sobald
RMR383HG_M_DE_op1.indd 6 15-9-24 2:12