Oregon Scientific SL929 Hockenheim User manual

1
EN
TABLE OF CONTENTS
About this guide ......................................... 2
Product overview ........................................ 3
Getting started ........................................... 5
Batteries .................................................. 5
Safety cord.............................................. 5
Switch between modes .......................... 5
Change settings ..................................... 5
Clock ........................................................... 6
Alarm........................................................... 6
Timer ........................................................... 7
Stopwatch................................................... 9
Pacer ........................................................12
Backlight ...................................................13
Safety and care........................................14
Warnings...................................................14
Troubleshooting........................................15
Specifications ...........................................16
Additional resources ................................19

2
EN
ABOUT THIS GUIDE
Congratulationsonyourselectionof theOregon
Scientific Hockenheim 500-Lap Stopwatch
(SL-929). This powerful device bundles clock,
alarm,stopwatch,timer,andpacerfeaturesinto
a single hand-held tool you can use for all your
sporting activities.
Keep this manual handy as you use your new
product. It contains practical step-by-step
instructions, as well as technical specifications
and warnings you should know.
In this box, you will find:
• Stopwatch
• Safety cord
• User manual

3
EN
PRODUCT OVERVIEW DESCRIPTIONS
1. Start / Stop button
2. Lap / Reset button
3. Mode button ( 5)
4. Backlight button ( 13)
5. Safety cord ( 5)
1
2
3
4
5

4
EN
Segment number ( 11)
Memory recall ( 11)
Lap time ( 9)
Split time ( 9)
Total time ( 9)
Laps available ( 10)
LCD ICON DESCRIPTION
LCD ICON DESCRIPTION
Alarm ( 6 , 7)
Backlight ( 13)
Stopwatch Mode ( 9)
Pacer Mode ( 12 , 13)
Timer Mode ( 7)
Clock / Calendar ( 6)
Elapsed time
Stopwatch units ( 9)
Lap number ( 11)

5
EN
GETTING STARTED
BATTERIES
Batteries are supplied with this product.
Replace them whenever the display becomes
dim. Use a coin to remove the battery
compartment lid (ontheback of theStopwatch).
Be sure to match the correct polarity, as shown
in the battery compartment.
SAFETY CORD
Thread the safety cord through the loop on the
bottom of the unit.
SWITCH BETWEEN MODES
Press MODE.
CHANGE SETTINGS
Press and hold MODE for 2 seconds. Then,
press LAP / RESET or START / STOP to
change each setting. Press and hold for
fast-setting mode. Press MODE to switch
between options.

6
EN
CLOCK
The Clock Mode shows
thedate,month,year, day
ofweek,currenttime,and
alarm status.
SET OR CHANGETHE CLOCK
1. Press MODE to switch to the Clock Mode.
2. Press and hold MODE for 2 seconds to
enter the setting mode.
3. Select the 12/24-hour format, second,
minute,hour, year, month,and date. Press
LAP / RESET or START / STOP tochange
the setting. Press MODE to confirm.
ALARM
When activated, the
alarm beeps continu-
ously for 30 seconds.

7
EN
SET ALARMTIME
1. Press MODE to switch to Alarm Mode.
2. Press and hold MODE for 2 seconds to
enter the setting mode.
3. Select the hour and minute. Press LAP /
RESET or START / STOP to change the
setting. Press MODE to confirm.
ACTIVATE / DEACTIVATE ALARM
In Alarm Mode, press START / STOP or LAP /
RESET. displays when the alarm is
activated.
TOTURNTHE ALARM OFF
Press any button.
TIMER
Use the Timer Mode to
measure a set length of
time, such as an hour, or
to compete against your
best time for an activity.
You can run up to 3
Timers simultaneously.

8
EN
SET TIMER
1. Press MODE to switch to Timer Mode.
2. Press and hold MODE for 2 seconds to
enter the setting mode.
3. Select the hour, minute, second, and count
method. There are three count methods,
as follows:
CS - Count down and stop
CR - Countdown and repeat
CU - Countdown, then count up
Press LAP / RESET or START / STOP to
change the setting. Press MODE to
confirm.
4. To set additional Timers, press LAP/
RESET, then repeat Steps 2 - 3.
START / STOP / PAUSETIMER
Press START / STOP.
CLEARTIMER
Stop the timer. Then, press and hold LAP/
RESET for 2 seconds.

9
EN
TIMER ALARM
An alarm will beep every second during the
last 5 seconds of the timer. A second alarm
will beep for 10 seconds at the end of the
timed period. Press any button to stop the
alarm.
STOPWATCH
With the stopwatch, you
can perform the following
tasks:
• Mark up to 500 laps
• View lap, split, and cumulative time
• Save, recall, and erase up to 99 memory
segments with date / time stamp
• Change the unit of measurement
SET STOPWATCH
1. Press MODE to
switch to Stopwatch
Mode. The following
informationwillshow:

10
EN
• Laps available ( )
• Number of segments saved
• Display format
• Stopwatch units ( )
•Stopwatch mode
2. (Optional) To change Stopwatch units,
press and hold MODE for 2 seconds. The
unit settings will flash. Then, press START
/ STOP to switch between the options.
• HR:MIN:SEC (1/100 second resolution)
• SEC (1/100 second resolution)
• HR (1/100000 hour resolution)
• MIN (1/1000 minute resolution)
Press MODE to confirm.
3. Press LAP / RESET to create a new
memory segment.
4. Press STOP / START to start the
Stopwatch and switch views.