Oriental motor PK Series User manual

HM-7428
OPERATING MANUAL
2-Phase Stepping Motor
PK Series PS Geared Type
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety
precautions.
• Please read it thoroughly to ensure safe operation.
• Always keep the manual where it is readily available.
Introduction
 Before using the motor
Only qualified personnel should work with the product.
Use the product correctly after thoroughly reading the section “Safety
precautions”.
The product described in this manual has been designed and manufactured
for use in general industrial machinery, and must not be used for any other
purpose. For the power supply use a DC power supply with reinforced
insulation on its primary and secondary sides. Oriental Motor Co., Ltd. is not
responsible for any damage caused through failure to observe this warning.
 Hazardous substances
RoHS (Directive 2002/95/EC 27Jan.2003) compliant
Safety precautions
The precautions described below are intended to prevent danger or injury to
the user and other personnel through safe, correct use of the product. Use the
product only after carefully reading and fully understanding these
instructions.
Warning
Handling the product without observing the instructions that accompany a
“Warning” symbol may result in serious injury or death.
• Do not use the product in explosive or corrosive environments, in the
presence of flammable gases, locations subjected to splashing water, or
near combustibles. Doing so may result in fire or injury.
• Assign qualified personnel the task of installing, wiring,
operating/controlling, inspecting and troubleshooting the product. Failure
to do so may result in fire or injury.
• Provide a means to hold moving parts in place for applications involving
vertical travel. The motor loses holding torque when the power is shut off,
allowing the moving parts to fall and possibly causing injury or damage to
equipment.
• Install the motor in an enclosure in order to prevent injury.
• Keep the input-power voltage within the specified range to avoid fire.
• Connect the lead wires securely according to the wiring diagram in order
to prevent fire.
• Do not forcibly bend or push the connector. Doing so may fire.
• Do not forcibly bend, pull or pinch the motor lead wire. Doing so may fire.
• For the power supply use a DC power supply with reinforced insulation on
its primary and secondary sides. Failure to do so may result in electric
shock.
• Turn off the power in the event of a power failure, or the motor will
suddenly start when the power is restored and may cause injury or damage
to equipment.
• Do not disassemble or modify the motor. This may cause injury. Refer all
such internal inspections and repairs to the branch or sales office from
which you purchased the product.
Caution
Handling the product without observing the instructions that accompany a
“Caution” symbol may result in injury or property damage.
• Do not use the motor beyond its specifications, or injury or damage to
equipment may result.
• Do not touch the motor during operation or immediately after stopping.
The surface is hot and may cause a skin burn(s).
• Do not hold the motor output shaft or motor lead wires. This may cause
injury.
• To prevent bodily injury, do not touch the rotating parts (output shaft) of
the motor during operation.
• Immediately when trouble has occurred, stop running and turn off the
driver power. Failure to do so may result in fire or injury.
• Provide an emergency-stop device or emergency-stop circuit external to
the equipment so that the entire equipment will operate safely in the event
of a system failure or malfunction. Failure to do so may result in injury.
• To dispose of the motor, disassemble it into parts and components as much
as possible and dispose of individual parts/components as industrial waste.
Precautions for use
• Conduct the insulation resistance measurement or withstand
voltage test separately on the motor and the driver
Conducting the insulation resistance measurement or withstand voltage test
with the motor and driver connected may result in injury or damage to
equipment.
• About grease of geared motor
On rare occasions, a small amount of grease may ooze out from the gearhead.
If there is concern over possible environmental damage resulting from the
leakage of grease, check for grease stains during regular inspections.
Alternatively, install an oil pan or other device to prevent leakage from
causing further damage. Oil leakage may lead to problems in the customer’s
equipment or products.
• Allowable torque
Operate the motor by making sure the sum of the acceleration/deceleration
torque at the starting/stopping of the motor and the load (friction) torque
doesn’t exceed the allowable torque. Operating the motor in excess of the
allowable torque may result in a damaged gear.
• Allowable speed range
Operate the motor at speeds within the allowable range. Operating the motor
at a speed outside the allowable range may result in a shorter gear life.
• Backlash
The gear output shaft is subject to backlash of 35´. To reduce the effect of
backlash, perform positioning operations from one direction only-either from
the CW direction or the CCW direction.
• Rotating direction of the gear output shaft
Rotating direction of the gear output shaft and the motor shaft are same
direction.
Checking the product
Verify that the items listed below are included. Report any missing or
damaged items to the branch or sales office from which you purchased the
product. Check the motor model number against the number shown on the
nameplate.
• Motor............................................................... 1 unit
• Connector lead wire [0.6 m (2 ft.)] ................. 1 pc. (PK2-L∗only)
∗ represents an alpha numeric indicating the motor type.
• OPERATING MANUAL (this document)..... 1 copy
Installation
 Location for installation
The motor is designed and manufactured for installation in equipment.
Install it in a well-ventilated location that provides easy access for inspection.
The location must also satisfy the following conditions:
• Inside an enclosure that is installed indoors (provide vent holes)
• Ambient temperature: −10 to +50 °C (+14 to +122 °F) (non-freezing)
• Ambient humidity: 85% or less (non-condensing)
• Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas)
or liquid
• Area not exposed to direct sun
• Area free of excessive amount of dust, iron particles or the like
• Area not subject to splashing water (rain, water droplets), oil (oil droplets)
or other liquids
• Area free of excessive salt
• Area not subject to continuous vibration or excessive shocks

• Area free of excessive electromagnetic noise (from welders, power
machinery, etc.)
• Area free of radioactive materials, magnetic fields or vacuum
 Installation method
Install the motor onto an appropriate flat metal plate having excellent
vibration resistance and heat conductivity. When installing the motor, secure
it with four bolts (not supplied) through the four mounting holes provided.
Leave no gap between the motor and plate.
Mounting-pilot
holder
(countersunk or
drilled through)
Metal plate
Mounting hole
Motor type∗Bolt size Tightening torque
[N·m (oz-in)] Effective depth [mm (in.)]
PK223P M3 1 (142) 6 (0.236)
∗ Enter the motor length in the box () within the model number.
 Permissible overhung load and permissible thrust load
The overhung load and thrust load on the motor’s output shaft or gear output
shaft must be kept within the permissible values listed below.
Permissible overhung load [N (lb.)]
Distance from the tip of motor’s output
shaft [mm (in.)]
Motor type∗0
(0) 5 (0.20) 10 (0.39) 15 (0.59) 20 (0.79)
Permissible
thrust load
[N (lb.)]
PK223PD-PS5
PK223PD-PS10
45
(10.1) 60 (13.5) 80 (18) 100 (22) −20 (4.5)
∗ Enter A(single shaft) or B(double shaft) in the box () within the model
name.
 Installing a load
When connecting a load to the motor, align the centers of the motor’s output
shaft and load shaft. Be careful not to damage the output shaft or the bearings
when installing a coupling or pulley to the motor’s output shaft.
Connection
B
A
(6)(5)(4)(3)(2)(1)
Red
(3)
Blue
(1)
(4) Black
(6) Green
Pin assignmentsWiring diagram
( ) Pin number
Pin No.2 and 5 are not used.
The colors of lead wires shown apply to the supplied cable or optional
connector lead wire. If you are using the connector set or when you are
providing your own connector or lead wire, connect based on the pin
numbers shown.
 Applicable connector and lead wire
The applicable connector and the lead wire are as follows.
Motor
type∗
Housing
Contact
(Molex) Lead wire Crimping
tool (Molex)
PK223P 51065-0600
50212-8XXX
AWG30 to 24 (0.05 to 0.2 mm2)
Outer sheath diameter
Ø1.4 mm (0.055 in.) or less
Strip length
1.3 to 1.8 mm (0.051 to 0.071 in.)
57176-5000
∗ Optional connector lead wires and connector set (sold separately) are
available from Oriental Motor.
Note • Secure the motor lead wire in place so that the
connection won’t be subjected to stress induced by a
bent lead wire or the lead wire’s own mass. The lead
wire’s radius of curvature should be as large as possible.
• When removing the motor lead wire, pull it out
horizontally toward the output shaft. The motor may be
damaged if force is applied in any other direction.
Inspection
It is recommended that periodic inspections be conducted for the items listed
below after each operation of the motor. If an abnormal condition is noted,
discontinue any use and contact your nearest office.
• Check for any unusual noises in the motor’s bearings (ball bearings) or
other moving parts.
• Are there any loose connector connections, or any scratches or signs of
stress in the motor lead wire?
• Are the motor’s output shaft and load shaft out of alignment?
• Unauthorized reproduction or copying of all or part of this manual is
prohibited.
• Oriental Motor shall not be liable whatsoever for any problems relating
to industrial property rights arising from use of any information, circuit,
equipment or device provided or referenced in this manual.
• Characteristics, specifications and dimensions are subject to change
without notice.
• While we make every effort to offer accurate information in the
manual, we welcome your input. Should you find unclear descriptions,
errors or omissions, please contact the nearest office.
• is a registered trademark or trademark of Oriental
Motor Co., Ltd., in Japan and other countries.
© Copyright ORIENTAL MOTOR CO., LTD. 2010
Printed on Recycled Pape
r
• Please contact your nearest Oriental Motor office for further information.
Headquarters Tokyo, Japan
Tel:[phone] Fax:[phone]
Tel:[phone] Fax:[phone]
Tel:[phone] Fax:[phone]
Technical Support Tel:[phone]
8:30
A.M. to 5:00 P.M. , P.S.T. (M-F)
7:30
A.M. to 5:00 P.M. , C.S.T. (M-F)
E-mail: [e-mail]
www.orientalmotor.com
Headquarters and Düsseldorf Office Tel:[phone] Fax:[phone]
Munich Office Tel:[phone] Fax:[phone]
Hamburg Office Tel:[phone] Fax:[phone]
Tel:[phone] Fax:[phone]
Tel:[phone] Fax:[phone]
Tel:[phone] Fax:[phone]
KOREA
Tel:[phone]~3 Fax:[phone]
Tel:[phone] Fax:[phone]
Tel:[phone] Fax:[phone]